GLORIA 405T High-Performance Sprayers Instruction Manual

GLORIA 405T High-Performance Sprayers

Accessories

General information about this user manual

This user manual is an integral part of the GLORIA device and must be continually available on or near the device. This user manual contains important instructions and information required for ensuring the safe use of the device! This user manual must be kept safe and passed on to any new owner! All warning notices are there to protect your personal safety!

Symbols on the device and in the user manual

• The user manual must be read in full by every person who is authorized to operate/use/maintain the device.
• Do not eat, drink or smoke until you have removed your protective clothing, careful-ly cleaned your hands and face, and rinsed out your mouth.
• Wear suitable protective clothing according to the spraying agents in use.
• Never use solvent-based or oily substances.
• Do NOT spray any explosive, highly flammable or combustible liquids with a flash point below +60°C, or any oxidizing or toxic substances.
• Do not use the device for spraying pesticides!
• Protect the device against long exposure to the sun and frost.
• Never point the spray jet at people or animals.
• Do NOT dispose of old devices as normal domestic waste.
• Environmentally appropriate dis- postal
• Recyclable packaging materials.
• The device can be used for car care.
• The device can be used in private or professional workshops.
• The device can be used industrially.
• The device can be used in auto repair shops/gas stations.
• Sealing material fluoropolymer rubber.
• Sealing material acrylonitrile butadiene Rubber.

Warning notices

WARNING
This level of warning notice indicates a potentially hazardous situation. Follow the instructions accompanying this warning notice in order to avoid serious injury or death.

CAUTION
This level of warning notice indicates a potentially hazardous situation which, if not avoided, may result in serious injury. Follow the instructions accompanying this warning notice in order to avoid serious injury.

ATTENTION
This level of warning notice indicates a potentially hazardous situation which, if not avoided, may result in material damage. Follow the instructions accompanying this warning notice in order to avoid material damage.

Note:
A note indicates additional information or illustrations that help you operate and facilitate the understanding of the device.

Intended use
This device is suitable for the application of spraying agents in the field of crafts and industry. Low-viscosity media, mineral oils, formwork oils and media in the PH range ≥ 5 and ≤ 9 may be sprayed. Compliance with the accompanying instructions is a prerequisite for the proper use of the device. The user manual also contains the operating, maintenance and servicing conditions. Always comply with the safety instructions/safety measures of the spraying agent manufacturers when applying spraying agents.

CAUTION
The danger is caused by improper use. This device can be dangerous if not used for its intended purpose. You should therefore observe the following safety instructions:

• Use the device for its intended purpose only.
• Note all instructions and information in the user manual.

Reasonably foreseeable misuse

• The device is not suitable for group 1 fluids according to Directive 2014/68/EU.
• The device is also not suitable for:
  • Explosive, highly flammable or combustible liquids with a flash point below +60°C
  • Oxidising or toxic media
  • Acids (pH ≤ 5), alkalis (pH ≥ 9)
  • Solvents or media containing solvents
  • Fuels
  • Wetting agents (surfactants) which may cause or promote cracks and fissures in the plastics used
  • Disinfectants and waterproofing agents as well as substances above 50°C
  • Liquids that are highly viscous, sticky or form residues and cannot be fully emptied or rinsed out of the device
  • Use in the food sector
  • Spraying pesticides
• On request, the device manufacturer will provide a detailed material parts list of the device for closer inspection.
• The manufacturer does not accept liability for any damage or injury resulting from unauthorised modifications to the device or its improper use.

Residual hazards
This device complies with the accepted rules of technology and the relevant safety requirements ! However, use of the device may present:

• Danger to life and limb of the operator or other persons.
• Damage to the device.
• Damage to the other items of property.

Limitation of liability
We expressly point out that according to product liability law we do not accept li ability for damage caused by our device, insofar as this has been caused by non-compliance with the operating instructions, improper use, improper repair or replacement of parts with non-genuine parts, or if repairs have not been carried out by the customer service team or an authorised expert. This also applies to accessories.

For your safety

This chapter contains important warning and safety instructions which must be observed when hand ling and using the device.

Basic safety instructions
Observe the following basic safety instructions to ensure the safe hand ling and use of the device:

NOTE

• Repairs to these devices must be performed exclusively by the service centres. Spare parts should be ordered from your dealer. If the parts are not in stock, the dealer will procure them as soon as possible.
• This device complies with the accepted rules of technology and the relevant safety requirements!
• This device may be used by child ren from 16 years and above and by persons with diminished phys ical, sensorial or mental capacities or lack of experience and know ledge if supervised or if they have been instructed with respect to safe use of the device and understand the risks that result from using it. Children must not play with the device. Cleaning and user maintenance must not be performed by children without supervision.
• This device must not be used if the operator is tired, ill or under the influence of alcohol or other drugs or medicines.
• Use the device as intended!
• Keep spraying equipment and media away from children and young persons under 16.
• In order to prevent damage and hazards resulting from improper use , you must observe the user manual and store it in a safe place!
• If the device is passed on to other persons, they must also be given the user manual!
• Always place the device on an even, flat surface.
• Secure the device during transport to prevent the spray liquid escaping.
• Each time before the sprayer is put into operation, regularly check to ensure the fault-free condi-tion and function of the pressurised/liquid-conducting operating elements and the safety valves. Pay particular attention to the tightness of the screw connection and screw joints. Check the mate-rial for the formation of cracks, brittleness and corrosion. If damage is suspected, take the unit out of operation immediately.
• Do not leave the device unattended while it is in operation.
• Protect the device against long exposure to the sun and frost.
• As a precautionary measure, we recommend that a particularly extensive inspection be per-formed – ideally by the manufacturer – after the sprayers have been in use for 2 years. It is forbidden to perform repairs on the container.
• Only use GLORIA original spares and accessories for the device.
• Never use worn, modified or defective replacement parts/accessories
• The device has a maximum service life of 10 years.

Health hazards

WARNING
Danger of death due to fire and/or explosion! Danger of death due to improper use of the device! Avoid having sources of ignition in the surrounding area. When spraying flammable liquids, do not spray on hot surfaces.

CAUTION
You may be exposed to hazards that could injure you when handling the device and the spraying agents. Always comply with the safety information/safety measures of the spray product manufacturer and the following safety instructions:

• Do not blow out blocked nozzles using the mouth.
• Do not point the end of the spraying lance at yourself when unscrewing it.
• Changes or improvements to the device are not permitted without the agreement of the manufacturer! Never bypass, modify or remove the safety equipment.

CAUTION
Danger to health through contact with the spraying agents! Spraying agents can cause damage to health if inhaled, swallowed or absorbed by the skin. Consult a doctor if you develop symptoms or are unsure. You should therefore observe the following safety instructions:

• Note safety instructions on the labels of the spraying agents used. Pay attention to the stated max. concentration. Certain liquids require the use of protective glasses, gloves or other safety measures.
• Always request a safety data sheet from the spraying agent manufacturer.

Danger due to damage to equipment ATTENTION Improper use can cause
damage to the device! For this reason, observe the following safety instructions:

• The device must not be pressurised for extended periods.
• Do not store the device in livestock buildings due to the ammonia vapours (dan-ger of brass cracking), do not fill with solutions containing nitrogen or phosphates.
• Do not store spraying agents in the device.

Before using the device

Delivery status
The device is shipped as standard as follows (see figure on page 2):

• A Base
• B Brass spray pipe with flat spray nozzle
• C Pressure gauge
• D Safety/vent valve
• E Brass quick closure valve
• F Pump handle with spray pipe mount
• G Filling strainer
• H Storage compartment for replacement seals/nozzles etc.
• I Adjustable carrying straps
• J 1 x user manual and product information (not shown).

Any accessory parts are packaged separately as part of the delivery.

Technical data

General
High-performance sprayers: 405 T, 405 TK, 405 TKS, 505 T, 505 TK, 410 T, 410 TI, 410 TK, 410 TKS, 510 T, 510 TK. Permissible positive operating pressure: 6 bar / Permissible operating temperature: 0°C to +50°C / Full pressure change (0-6 bar) for max. 5000 load changes / Spray pipe holder / Pressure relief valve / Pressure gauge / Flat spray nozzle: 80° / Max. output: 1 l/min / Reaction force on the noz-zle: < 5 N / Pump material: brass / Mesh size of filter in quick closure valve: 0.9 mm / Residual quantity following horizontal emptying: none

Individual

High-performance sprayers| 405 T| 405 TK| 405 TKS| 505 T| 505 TK| 410 T| 410 TI| 410 TK| 410 TKS| 510 T| 510 TK
---|---|---|---|---|---|---|---|---|---|---|---
Max. filling capacity in litres| 5| 5| 5| 5| 5| 10| 10| 10| 10| 10| 10
Total container content in litres| 8| 8| 8| 8| 8| 13,7| 13,7| 13,7| 13,7| 13,7| 13,7
Empty weight in kg| 4,4| 4,4| 4,5| 4,35| 4,35| 5,6| 5,6| 7,0| 5,7| 5,5| 7,0
Compressor connection| –| x| x| –| x| –| –| x| x| –| x
Backrest| –| –| –| –| –| x| x| x| x| x| x
Oil-resistant device| x| x| x| x| x| x| –| x| x| x| x
Container material:

– Steel, internally coated

– Stainless steel

| ****

x

–

| ****

x

–

| ****

x

–

| ****

–

x

| ****

–

x

| ****

x

–

| ****

x

–

| ****

x

–

| ****

x

–

| ****

–

x

| ****

–

x

Special accessories: see figure on page 2; further accessories at www.gloriagarten.de

Assembly

5 litre device >> figures

10 litre device >> figures

Commissioning

WARNING
Before putting it into operation, observe Chapter 2 “For your safety”.

CAUTION
Danger to health due to escaping spraying agents! A leaking device or leaking components may result in draining or spouting of spraying agent. You should therefore observe the following safety instructions:

• Prior to each use, check the device to ensure fault-free condition and leak-tightness. To perform the leak test, fill the container with water!
• Inspect all screw joints for tight-fitting.
• The device 410TKS (ref. 416.8000) is supplied without a hose line. When retrofitting the device, a suitable hose line corresponding to the classification of the device in the Pressure
• Equipment Directive 2014/68 EU must be used.

5/10 litre devices >> Inspecting the safety valve

**Venting the container, draining the water and filling with spraying agent

**

ATTENTION

Certain versions of the device are equipped with a compressor connection. The following must be observed during use:

• Activate the safety/vent valve – red button – until the device is depressurised.
• Prior to filling the sprayer, observe the instructions relating to particular hazards (R-phrases/German Hazardous Substances Ordinance [GefStoffV]) and safety advice (S-phrases/German Hazardous Substance Ordinance [GefStoffV]) that are provided on the chemical containers according to regulations.
• Observe max. fill level (see technical data). The regulations of the spraying agent manufacturer specify the correct dosage and concentration.

Spraying

CAUTION
You may be exposed to hazards that could injure you when handling the device and the spraying agents. You must therefore always comply with the safety instruc-tions/safety measures in this user manual, as well as the following instructions:

• The device must only be operated when suspended in a vertical or steep upright position.
• Pressing the actuation lever down on the quick closure valve initiates the spraying process. This can be interrupted immediately by releasing the actuation lever.
• The optimum spray pressure for the best possible distribution of the spray liquid is 2-6 bar.
• The pumping procedure makes it possible to influence the spray pressure at the nozzle.
• Perform re-pumping if the spray pressure falls.

NOTE
You may be exposed to hazards that could injure you when handling the device and the spraying agents. You must therefore always comply with the safety instruc-tions/safety measures in this user manual, as well as the following instructions:

• The device must only be operated when suspended in a vertical or steep upright position.
• Pressing the actuation lever down on the quick closure valve initiates the spraying process. This can be interrupted immediately by releasing the actuation lever.
• The optimum spray pressure for best possible distribution of the spray liquid is 2-6 bar.
• The pumping procedure makes it possible to influence the spray pressure at the nozzle.
• Perform re-pumping if the spray pressure falls.

Shutting down

Emptying and cleaning

CAUTION
Danger to health due to escaping spraying agents! Pay attention to the safety instructions in this manual. Observe applicable laws and the specifications of the agent manufacturers when disposing of residual quantities.

**Maintenance

**

NOTE

• Observe the national regulations concerning occupational safety which apply to the place of operation as well as the applicable national regulations for operations. An expert inspection must be performed – ideally by the maintenance service of the manufacturer – to establish whether hazard-free operation remains possible. This should be performed in the event of defects that may impair safety in particular, and must be performed at least every 5 years in any case.
• Only use original GLORIA spare parts for repairs. (see GLORIA spare parts shop https://shop.gloriagarten.de).
• Repairs must only be carried out by a GLORIA service point.
• It is forbidden to perform repair work on the container (such as welding and soldering).
• Further accessories can be found at www.gloriagarten.de

Storage
You may be exposed to hazards that could injure you when handling the device and the spraying agents. You must therefore store the device and the spraying agents out of the reach of children.

Problems with the device

Hose lose

| Tighten coupling nut and carry out pressure test with water
The spray pattern of the nozzle is not OK| Nozzle partially blocked

Filter in quick closure valve contaminated

| ****

Clean filter or nozzle

The pump does not build

up any pressure

| O-ring on piston is

worn

| Replace O-ring

Disposal & Legislation

Environmental protection & disposal of the device
The device must be separated according to the different materials and disposed of at a recycling collection point. The materials can be recycled according to their designations.

Disposal of packaging
The packaging materials have been selected according to environmentally- suitable and disposal-related aspects and are therefore recyclable. Returning the packaging to the material circulation saves raw materials and reduces the level of waste. Please dispose of unwanted packaging materials according to applicable local regulations.

EU Declaration of Conformity
EU Declaration of Conformity for a module as defined by Article 4, section 2 of the Directive on pressure equipment 2014/68/EU GLORIA Haus- und Gartengeräte GmbH Därmannsbusch 7D-58456 Witten confirms that the high- performance sprayers (consisting of a pressure container (module A2) with a safety valve and pressure gauge, pump and tubing; part no.: see type label).

Part. no.

• 405.…, 406…, 407… }
• 505…, 506… }
• 410…, 411…, 412…, 413…, 414… }
• 415…, 416…, 416.8000
• 510…, 512…, 513… }

Certificate no. (module A2)

• 07 202 1403 Z 0169 16 D 1148

comply with the Directive on pressure equipment 2014/68/EU and the accepted rules of engineering. The conformity evaluation procedure for the module is based on module A2 (Appendix III, number 2) of Directive 2014/68/EU.

Notified body: TÜV NORD Systems GmbH & Co.KG. Große Bahnstraße 31; 22525 Hamburg, Germany (0045)

The device 410TKS (ref. 416.8000) is supplied without a hose line. When retrofitting the device, a suitable hose line corresponding to the classification of the device in the Pressure Equipment Directive 2014/68 EU must be used.

Witten, 30/06/2021 Ludger Strunk (Head of Development and Design)

References

• Dein Garten Online Shop | Garten.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>