BUYTHA 1500W Solar Street Lights Outdoor User Manual
- June 14, 2024
- BUYTHA
Table of Contents
SOLAR STREET LIGHT
User Manual
Reading this user manual thoroughly before using is a must for your safety and the safety of others.
PACKING LIST
Light Body Light-Arm
Remote Control Mounting Screws
SPECIFICATIONS
| Charging Time | 6-8 Hours |
|---|---|
| Solar Panel | 6V30W |
| Battery Capacity | 24000MAH |
| Fully Charged Lighting | 16-24 Hours |
| Lighting Range | 2200 sq ft-2700 sq ft |
| Lamp Bead QTY | 1679 PCS |
| Color Temperature | 6500K |
| Working Temperature | -10°F ~ 100°F |
| Waterproof Rating | IP66 |
| Warranty Period | 24 Months |
| Installation Height | 16-26 ft |
INITIAL TEST
After installing the remote control battery, press the “ ” button of the remote control to turn on the lamp, and press the “OFF” button to turn off the lamp. You can also press other buttons to enter other working modes of lamps and lanterns. The functions of various working modes corresponding to lamps and lanterns and remote control system and buttons on the remote control will be described in detail later.
After debugging or inspecting the lamp, first place the solar panel and lamp in a place with sufficient light. Cover the solar panel with opaque material, and the lamp will be on. The solar panel can work normally and the battery can charge with normal electricity.
ATTENTION
- The installation of solar panels should be in direct sunlight as much as possible, without being blocked by buildings or trees, and ensure the longest acceptable irradiation time (the solar panels cannot be installed under glass or indoors). Only by correctly and scientifically installing solar panels they will have the best charging effect.
- The luminescent surface of the lamp is made of PC plastic, and the surface of the solar photovoltaic panel is made of glass. As the most important structures of the lamp, these two pieces are fragile. Please handle them with care during transportation, handling, storage and installation, and do not press them heavily to avoid damaging the structure of the lamp.
- Clean the PC cover and solar panel from the lamps regularly to keep good light transmittance of lamps. Be careful to not to clean the lamps with water or a corrosive solution, but rather with a dry rag.
- This lamp should be stored in a place with good air circulation and less dust. The ambient temperature should be between -10°F ~ 100°F , and it should not be stored in an icy environment. Keep away from corrosive substances, stay idle for a long time, and need to charge and discharge once a month.
- This product cannot be disassembled without permission. Do not use any charger to charge this product.
INSTRATIONS
(1) Loosen the bolt on the lamp.
(2) Lock the light tightly to the light pole.
-
Arm
-
Pole
-
M10*70 Screw, Nut
-
H (16.4-19.7ft)
-
Wall
-
Arm
Expansion Screw Fixation
TWO LIGHTING MODES
CHARGING DURING
THE DAY 6-8 hours
Larger solar panels
WORKING TIME
AT NIGHT 18-24 hours
Longer Lighting Time
MOTION SENSOR MODE
No pedestrian at night. 30% brightness.
When a pedestrian walks into the induction area -100% brightness.
REMOTE CONTROL BUTTONS
OFF: Turn off the lights:
The light will not come on automatically the next day. If you need the light
to come on, you need to turn it on again with the remote control.
2H: Two-Hour Timed Lighting:
Fixed on 100% brightness two hours.
4H: Four-Hour Timed Lighting:
Fixed on 100% brightness four hours.
6H: Six-hour timed lighting:
Fixed on 100% brightness six hours.
: Fixed on 100% brightness:
Automatically turns on at dusk and off at dawn.
:Motion sensor mode:
When people are far away, 30% brightness. When people are close, 100%
brightness.
SOLUTIONS TO COMMON PROBLEMS
Damaged or Missing Parts
Check all the hardware first according to the user manual’s packing list. If you find the parts are damaged or missing, please contact us to resend one within one day.
The Street Light Does Not Work
New products: Charge it for 1-2 days with direct sunlight. After charging, please use the “ON” button on the remote to test whether it can charge and light up normally.
Stopped working: Please check whether any of the parts are loosely connected. After ensuring the connection, charge it for several hours to test whether the street light works again.
If the solutions above do not work, the cause might be internal. Please contact our technical support team for assistance in resolving your problem.
Low-light Level
Low power: The street light might be without enough power for high light, please charge it on a sunny day with maximum direct sunlight.
SAFETY PRECAUTIONS
Warning
Do not look directly at the light as it can have adverse effects on eyesight.
| Do not disassemble and reassemble the product, as doing so will take it out
of warranty.
---|---
- If the cloudy day continues, the battery level will be low and the light will become dark. It will not light, and it may flash again, which is normal. In that case, please perform the initial charge with sunlight.
- Use the required accessories correctly. If you fail to do this, it may cause a malfunction.
- Check the mounting screws and binding bands of the solar light twice a year to check whether they are loose or rattled.
- Clean off dust and dirt on the panel surface periodically, as it can affect charging performance. If there is snow on the panel surface, remove that as well.
- LED chips and batteries cannot be replaced.
WARRANTY & SERVICE
The solar street light comes with a two-year warranty and lifetime technical support. If you have any questions or concerns, please feel free to contact us.
Email: support@buytha.com 1-833-872-6581
Facebook: @buythatech
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>