beurer BC 28 Wrist Blood Pressure Monitor Instruction Manual

beurer BC 28 Wrist Blood Pressure Monitor

Read these instructions for use carefully and keep them for later use, be sure to make them accessible to other users and observe the information they contain.

Dear customer,

Thank you for choosing a product from our range. Our name stands for high- quality, thoroughly tested products for applications in the areas of heat, weight, blood pressure, body temperature, pulse, gentle therapy, massage, beauty, baby and air.

With kind regards,

Your Beurer team

Included in delivery

Check that the exterior of the cardboard delivery packaging is intact and make sure that all contents are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

1. 1x Blood pressure monitor with cuff
2. 2x 1.5 V LR03 AAA batteries
3. 1x Storage box
4. 1x Instructions for use

Signs and symbols

The following symbols are used in these instructions for use, on the packaging and on the type plate for the device and the accessories:

Intended use

The wrist blood pressure monitor serves as a non-invasive way of measuring and monitoring arterial blood pressure and pulse values in adults with wrist circumferent of 14 – 19.5 cm. This allows you to quickly and easily measure your blood pressure and pulse, save the measurements and display the development of the measurements. The recorded values are classified and evaluated graphically. You are also warned of possible existing cardiac arrhythmia.

Warning and safety notes

Notes on use

• In order to ensure comparable values, always measure your blood pressure at the same time of
• Do not take a measurement within 30 minutes of eating, drinking, smoking or
• Before the initial blood pressure measurement, make sure always to rest for about 5
• Furthermore, if you want to take several measurements in succession, make sure always to wait for at least 1 minute between the individual
• Repeat the measurement if you are unsure of the measured
• The measured values taken by you are for your information only – they are no substitute for a medical Discuss the measured values with your doctor and never base any medical decisions on them (e.g. medicines and their dosages).
• Using the blood pressure monitor outside your home environment or whilst on the move (e.g. whilst travelling in a car, ambulance or helicopter, or whilst under- taking physical activity such as playing sport) can influence the measurement accuracy and cause incorrect
• Do not use the blood pressure monitor on newborns or patients with pre-eclampsia. We recommend consulting a doctor before using the blood pressure monitor during
• In the case of restricted circulation on the arm as a result of chronic or acute vascular diseases (including vascular constriction), the accuracy of the wrist measurement is In this case you should use an upper arm blood pressure monitor instead.
• This device is not intended for use by people (including children) with restricted physical, sensory or mental skills or a lack of experience and/or a lack of knowledge, unless they are supervised by a person who has responsibility for their safety or they receive instructions from this person on how to use the device. Supervise children around the device to ensure they do not play.
• Cardiovascular diseases may lead to incorrect measurements or have a detrimental effect on measurement The same also applies to very low blood pressure, diabetes, circulatory disorders and arrhythmias as well as chills or shaking.
• The blood pressure monitor must not be used in connection with a high-frequency surgical.
• Only use the device on people who have the specified wrist measurement.
• Please note that when inflating, the functions of the limb in question may be.
• During the blood pressure measurement, the blood circulation must not be stopped for an unnecessarily long If the device malfunctions, remove the cuff from the arm.
• Do not allow sustained pressure in the cuff or frequent measurements. The resulting restriction of the blood flow may cause.
• Make sure that the cuff is not placed on an arm in which the arteries or veins are undergoing medical treatment, e.g. intravascular access or intravascular therapy, or an arteriovenous (AV).
• Do not use the cuff on people who have undergone it.
• Do not place the cuff over wounds as this may cause further.
• Place the cuff on your wrist Do not place the cuff on other parts of the body.
• The blood pressure monitor can only be operated with
• To conserve the batteries, the blood pressure monitor switches off automatically if you do not press any but- tons for one
• The device is only intended for the purpose described in these instructions for The manufacturer is not liable for damage resulting from improper or incor- rect use.

Instructions for storage and maintenance

• The blood pressure monitor is made from precision and electronic components. The accuracy of the measured values and service life of the device depend on careful handling:

• Protect the device from impacts, humidity, dirt, marked temperature fluctuations and direct sunlight.

• Do not drop the device.

• Do not use the device in the vicinity of strong electromagnetic fields and keep it away from radio systems or mobile

• We recommend that the batteries be removed if the device will not be used for a prolonged period of time.

 Notes on handling batteries

• If your skin or eyes come into contact with battery fluid, rinse the affected areas with water and seek medical
• Choking hazard! Small children may swallow and choke on batteries. Therefore, store batteries out of the reach of small children.
• Observe the plus (+) and minus (-) polarity
• If a battery has leaked, put on protective gloves and clean the battery compartment with a dry
• Protect batteries from excessive
• Risk of explosion! Do not throw batteries into a
• Do not charge or short-circuit
• If the device is not to be used for a relatively long period, take the batteries out of the battery
• Use identical or equivalent battery types
• Always replace all batteries at the same
• Do not use rechargeable batteries.
• Do not disassemble, split or crush the

Notes on electromagnetic compatibility

• The device is suitable for use in all environments listed in these instructions for use, including domestic

• The use of the device may be limited in the presence of electromagnetic This could result in issues such as error messages or the failure of the display/device.

• Avoid using this device directly next to other devices or stacked on top of other devices, as this could lead to faulty If, however, it is necessary to use the device in the manner stated, this device as well as the other devices must be monitored to ensure they are working properly.

• The use of accessories other than those specified or provided by the manufacturer of this device can lead to an increase in electromagnetic emissions or a decrease in the device’s electromagnetic immunity; this can result in faulty operation.

• Failure to comply with the above can impair the performance of the device.

Device description

1. Display 3
2. Wrist cuff
3. Risk indicator
4. Start/stop button I
5. Memory button M 6
6. Battery 4
7. compartment lid

Information on the display

1. Systolic pressure
2. Risk indicator
3. Diastolic pressure
4. Calculated pulse rate
5. Cardiac arrhythmia symbol
6. Pulse symbol
7. User memory
8. Memory space number/ memory display for average value (A), morning (AM), evening (PM)
9. Battery replacement symbol
10. Time and date
11.  Release air (arrow)

Initial use

Inserting the battery ****

• Remove the battery compartment lid on the left side of the
• Insert two 5V micro (alkaline type LR03) batteries.
• Make sure that the batteries are inserted the correct way round in accordance with the Do not use rechargeable batteries.
• Carefully close the battery compartment lid again. If the battery replacement symbol is displayed, you can no longer perform any measurements and must replace all batteries.

Setting the hour format, date and time

It is essential that you set the date and time. Otherwise, you will not be able to save your measured values correctly with a date and time and access them again later.

There are two different ways to access the menu from which you can adjust the settings:

• Before initial use and after each time you replace the battery:

When inserting the batteries into the device you will be taken to the relevant menu automatically.

• If the batteries have already been inserted

With the device switched off press and hold the

START/STOP button for approx. 5 seconds.

In this menu you can adjust the following settings in succession:

Hour format

• Press and hold the START/STOP button for 5 seconds or insert The full display appears.
• Select the desired hour format using the memory button M and confirm with the START/STOP button.

Date

The year flashes on the display.

• Select the desired year using the memory button M and confirm with the START/STOP button.

The month flashes on the display.

• Select the desired month with the memory button M and confirm with the START/ STOP button.

The day flashes on the display.

• Select the desired day using the memory button M and confirm with the START/STOP button.

If the hour format is set as 12h, the day/month dis- play sequence is reversed.

Time

The hours flash on the display.

• Select the desired hour using the memory button M and confirm with the START/ STOP button.

The minutes flash on the display.

• Select the desired minute using the memory button M and confirm with the START/ STOP button.

Once all the data has been set, the device switches off automatically.

Usage

• Ensure the device is at room temperature before measuring. The measurement can be performed on the left or right wrist.

Attaching the cuff

• Expose your Ensure that the circulation of the arm is not hindered by tight clothing or similar.
• Place the cuff on the inside of your wrist.
• Fasten the cuff with the hook-and-loop fastener so that the upper end of the display is 1 cm below the heel of your hand.
• The cuff must be fitted tightly around the wrist, but must not constrict.

Blood pressure may vary between the right and left arm, which may mean that the measured blood pressure values are different. Always perform the measurement on the same arm. If the values between the two arms are significantly different, please consult your doctor to determine which arm should be used for the measurement.

Adopting the correct posture

• Before the initial blood pressure measurement, make sure always to rest for about 5 Otherwise deviations can occur.
• You can take the measurement while sitting or lying To take your blood pressure, make sure you are sitting comfortably with your arms and back leaning on something. Do not cross your legs. Place your feet flat on the ground. Make sure to support your arm and bend it. Always make sure that the cuff is at heart level. Otherwise, significant deviations can occur. Relax your arm and the palm of your hand.
• To avoid falsifying the measurement, it is important to remain still during the measurement and not to speak.
• Wait for at least 1 minute before taking another measurement.

Performing the blood pressure measurement

As described above, attach the cuff and adopt the posture in which you want to perform the measurement.

• Press the START/STOP button to start the blood pressure monitor. All displays will illuminate briefly.

• The last measured value is displayed and the blood pressure monitor automatically begins the measurement after 3 seconds.

You can cancel the measurement at any time by pressing the START/STOP button.

As soon as a pulse is found, the pulse symbol is displayed.

• Systolic pressure, diastolic pressure and pulse measurements are displayed.
• appears if the measurement has not been performed properly. Observe the chapter on error messages/troubleshooting in these instructions for use and repeat the measurement.
• Now select the desired user memory by pressing the memory button. If you do not select a user memory, the measurement is stored in the most recently used user memory. The relevant or symbol appears on the display.
• Press the START/STOP button to switch off the blood pressure monitor. The measurement is then stored in the selected user memory. If you forget to turn off the device, it will switch off automatically after approx. 1 minute.] In this case, too, the value is stored in the selected or] most recently used user memory. Wait for at least 1 minute before taking another measurement.

Evaluating results Cardiac arrhythmia

This device can identify potential disruptions of the heart rhythm when measuring and, if necessary, indicate this after the measurement with the symbol.

This can be an indicator of arrhythmia. Arrhythmia is an illness in which the heart rhythm is abnormal because of flaws in the bioelectrical system that regulates the heartbeat. The symptoms (skipped or premature heartbeats, pulse being slow or too fast) can be caused by factors such as heart disease, age, physical make-up, excess stimulants, stress or lack of sleep. Arrhythmia can only
be determined through an examination by your doctor. If the symbol is shown on the display after the measurement has been taken, repeat the measurement. Please ensure that you rest for 5 minutes beforehand and do not speak or move during the measurement. If the symbol appears frequently, please consult your doctor. Self-diagnosis and treatment based on the measurements can be dangerous. Always follow your doctor’s instructions.

Risk indicator

The measurements can be classified and evaluated in accordance with the following table. However, these standard values serve only as a general guideline, as the individual blood pressure varies in different people and different age groups etc. It is important to consult your doctor regularly for advice. Your doctor will tell you your individual values for normal blood pressure as well as the value above which your blood pressure is classified as dangerous. The classification on the display and the scale on the device shows which category the recorded blood pressure values fall into. If the values of systole and diastole fall into two different categories (e.g. systole in the “High normal” category and diastole in the “Normal” category), the graphical classification on the device always shows the higher category; for the example given this would be “High normal”.

Blood pressure value category| Systole

(in mmHg)

| Diastole

(in mmHg)

| Action
---|---|---|---
Level 3: severe

hypertension

|

≥ 180

|

≥ 110

| Seek medical attention
Level 2: moderate

hypertension

|

160 – 179

|

100 – 109

| Seek medical attention
Level 1: mild

hypertension

|

140 – 159

|

90 – 99

| Regular monitoring by

doctor

High normal

|

130 – 139

|

85 – 89

| Regular monitoring by

doctor

Normal| 120 – 129| 80 – 84| Self-monitoring
Optimal| < 120| < 80| Self-monitoring

Source: WHO, 1999 (World Health Organization)

Saving, accessing and deleting measured values

The results of every successful measurement are stored together with the date and time. The oldest measurement is overwritten in the event of more than 60 measurements.

• To retrieve the measurement, press the memory button M.
• Flashes on the display. The average value of all saved measured values in this user memory is displayed.
• To change the user memory, press and hold the memory button M for approx. 2 seconds.
• Press the memory button M.

AM flashes on the display.

• The average value of the morning measurements for the last 7 days is displayed (morning: 5 a.m. – 9 a.m.).
• Press the memory button M.

PM flashes on the display.

• The average value of the evening measurements for the last 7 days is displayed (evening: 6 p.m. – 8 p.m.).
• When you press the memory button M again, the last individual measurement is displayed (in this example, measurement 03).
• When you press the memory button M again, you can view your individual measured
• To switch the device off again, press the START/ STOP button.
• You can exit the menu at any time by pressing the START/STOP button.
• To clear the relevant user memory, you must first select a user
• Start the retrieval of the average measured A flashes on the display and the average value of all saved measured values in this user memory is displayed.
• Press and hold the memory button M and the START/STOP button for 5 seconds, depend- ing on the user memory you are in.

All values of the current user memory are deleted and the device switches off.

Cleaning and maintenance

• Clean the device and cuff carefully using a slightly damp cloth
• Do not use any cleaning agents or
• Under no circumstances hold the device and cuff underwater, as this can cause liquid to enter and damage the device and
• If you store the device and cuff, do not place heavy objects on the device and Remove the batteries.

What if there are problems?

| The systolic or diastolic pressure could not be measured.| Please wait one minute and repeat the measurement.

Ensure that you do not speak or move during the measurement.

| The systolic or diastolic pressure is outside of the measurement range.| Please wait one minute and repeat the measurement.

Ensure that you do not speak or move during the measurement.

If the message is displayed again, you should seek medical assistance and check the accuracy of your procedure.

| The cuff was not attached correctly.| Please observe the information in the chapter on “Attaching the cuff”.

1.5 seconds.

| Please wait one minute and repeat the measurement.

Ensure that you do not speak or move during the measurement.

If the message is displayed again, you should seek medical assistance and check the accuracy of your procedure.

Er 6| Pumping up takes longer than 180 seconds.| Please take another measurement to check whether the cuff can be correctly inflated.

Please observe the information in the chapter on “Attaching the cuff”.

| There is a system or device error.| Please contact customer service.
| The batteries are almost empty.| Insert new batteries into the device.

Disposal

Repairing and disposing of the device

• Batteries do not belong in the household Please dispose of empty batteries at the collection points intended for this purpose.
• Do not open the Failure to comply will invalidate the warranty.
• Do not repair or adjust the device Proper operation can no longer be guaranteed in this case.
• Repairs must only be carried out by Customer Services or authorised
• Before making a claim, please check the batteries first  and replace them if
• For environmental reasons, do not dispose of the device in the household waste at the end of its useful life. Dispose of the device at corresponding collection points in your country.
• Dispose of the device in accordance with EC Directive

WEEE

(Waste Electrical and Electronic Equipment). If you have any questions, please contact the local authorities responsible for waste disposal.

 Battery disposal

• Empty, completely flat batteries must be disposed of through specially designated collection boxes, red recycling points or electronics retailers. You are legally required to dispose of the batteries.

The codes below are printed on batteries containing harmful substances:

• Pb = Battery contains lead,
• Cd = Battery contains cadmium,
• Hg = Battery contains mercury.

Technical specifications

The serial number is located on the device or in the battery compartment. Technical information is subject to change without notification to allow for updates.

• This device complies with the European standard EN 60601-1-2 (compliance with CISPR 11, IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-8) and is subject to special precautionary measures with regard to electromagnetic compatibility. Please note that portable and mobile HF communication systems may interfere with this device.
• The device complies with the EU Medical Devices Directive 93/42/EEC, the German Medical Devices Act (Medizinproduktgesetz) and the standards EN 1060-1 (Non-invasive sphygmomanometers – Part 1: General requirements), EN 1060-3 (Non-invasive sphygmoma- nanometers – Part 3: Supplementary requirements for electro-mechanical blood pressure measuring systems) and IEC 80601-2-30 (Medical electrical equipment – Part 2 – 30: Particular requirements for the basic safety and essential performance of automated non-invasive sphygmomanometers).
• The accuracy of this blood pressure monitor has been carefully checked and developed with regard to a long useful If the device is used for commercial medical purposes, it must be regularly tested for accuracy by appropriate means. Precise instructions for checking accuracy may be requested from the service address.

Warranty/service

Beurer GmbH, Söflinger Straße 218, 89077 Ulm, Germany (hereinafter referred to as “Beurer”) provides a warranty for this product, subject to the requirements below and to the extent described as follows.

The warranty conditions below shall not affect the seller’s statutory warranty obligations which ensue from the sales agreement with the buyer. The warranty shall apply without prejudice to any mandatory statutory provisions on liability. Beurer guarantees the perfect functionality and completeness of this product. The worldwide warranty period is 5 years, commencing from the purchase of the new, unused product from the seller. The warranty only applies to products purchased by the buyer as a consumer and used exclusively for personal ,purposes in the context of domestic use. German law shall apply. During the warranty period, should this product prove to be incomplete or defective in functionality in accordance with the following provisions, Beurer shall carry out a repair or a replacement delivery free of charge, in accordance with these warranty conditions.

If the buyer wishes to make a warranty claim, they should approach their local retailer in the first instance: see the attached “International Service” list of service addresses. The buyer will then receive further information about the processing of the warranty claim, e.g. where they can send the product and what documentation is required. A warranty claim shall only be considered if the buyer can provide Beurer, or an authorized Beurer partner, with a copy of the invoice/purchase receipt, and the original product.

The following are explicitly excluded from this warranty

• deterioration due to normal use or consumption of the product;
• accessories supplied with this product which are worn] out or used up through proper use (e.g. batteries, rechargeable batteries, cuffs, seals, electrodes, light sources, attachments and nebulizer accessories);
• products that are used, cleaned, stored or maintained improperly and/or contrary to the provisions of the instructions for use, as well as products that have been opened, repaired or modified by the buyer or by the service centre not authorised by Beurer;
• damage that arises during transport between manufacturer and customer, or between the service centre and customer;
• products purchased as seconds or as used goods;
• consequential damage arising from a fault in this product (however, in this case, claims may exist arising from product liability or other compulsory statutory liability provisions).

Repairs or exchanges in full does not extend the warranty period under any circumstances.

References

• Was ist Blutdruck?
• Blutdruck - Wissenswertes über den Blutkreislauf
• Beurer Gesundheitsratgeber
• Beurer Gesundheitsratgeber
• Beurer Health Guide
• Beurer Health Guide
• Beurer — Beurer North America

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>