orient electric Apex-FX 1200mm Ceiling Fan Instruction Manual
- June 5, 2024
- orient electric
Table of Contents
orient electric Apex-FX 1200mm Ceiling Fan
SAFETY INSTRUCTIONS
- Ensure that the supply is AC and the Voltog is as per the specification printed on the name plate.
- There are no consumer serviceable parts inside this fan, Do not attempt to open/repair the fan on your own, doing so could cause damage to the fan and/or lead to personal injury.
- Use wire connector for wire joints, not just tape.
- Ensure that the height of the fan from the ground should be more then 2.3m when it is installed.
- Ensure that the distance of blade from wall of the room should be more than 1.5m when it is installed.
- This appliance is not intended for use by person (including children) with reduced physical sensory or mentol capabilities , or lock of experiance and knowledge , unless the have been given supervision or Instruction concerning use of the appliance by a person reponsible for their safety.
- Children should be supervised to nsure that they do not play with, appliance.
INSTALLATION INSTRUCTION
-
REMOVE THE SAFETY SCREW ① FROM THE DOWN ROD AND DOWN RON BOLT ② FOR SHAKLE KIT PACK/DOWN ROD.
-
INSERT DOWN ROD OVER SHAFT, ALIGN SAFETY SCREW HOLE ③ ON DOWN ROD WITH TAPPED HOLE ④ ON SHAFT.
-
INSERT OOWN ROD BOLT ② & SAFETY SCREW ① IN DOWN ROD ANF RLILGN THEM PROPERTY.
-
TIGHTEN SRFETY SCREW ① & THE DOWN ROD BOTT ② WITH NUT AND LOCK THE SPLIT PIN.
-
REMOVE THE DOWN ROD CAP ⑥ & INSERT THE CANOPIES ⑦ AND PUT THE OOWN ROD CAP ⑥ BACK INRO THE DOWN ROD.
-
PASS SUPP.LY WIRES ⑤ THROUGH THE DOWN ROD, PULL OUT FROM HOLE AND CONNECT THE SUPPLY WIRES WITH MOTOR TERMINAL.
-
UNSCREW THE SHACKLE KIT BOLT ⑧ AND INSERT THE SHACKLE KIT ⑨ INTO CEILING HOOK. INSERT THE DOWN ROD INTO SHACKLE KIT.
-
INSERT THE SHACKLE KIT BOLT ⑧ AND TIGHTEN WITH NUT, LOCK . THE SP.LIT PIN AND CONNECT THE SUPPLY WIRES TO MAIN SUPPLY.
-
ADJUST THE ,TOP CANOPY ID WITH CEILING AND TIGHTEN IT WITH SCREW PROVIDED IN CANOPY.
-
ADJUST THE BOTTOM CANOPY ⑦ AND FIX IT WITH SCREWSA PROVIDED, MAINTAIN APPROPRIATE GAP FROM TOP COVER. ⑩
-
ASSEMBLE BLADES ⑪ USING SPRLING WASHER ⑫ & SCREWS ⑬ AND EASTLRE ORMPIRG WASHER ⑭ SHOULD NOT BE REMOVED WHILE RSSEMBLLNG.
INSTRUCTION FOR INSTALLATION OF REGULATOR
Connect the regulator in series with the fan as shown in circuit diagram.
Applicable for Resistance Regulator
- Mount the regulator base plate on switch board with screws & nuts.
- Connect the regulator in series with the fan as shown in the circuit diagram.
- Place the cover in possible & tighten the two screws.
CAUTION
- Never open or try to loosen screws on the base plate.
Aplicable for Elecronic Regulator
- Mount the regulator on a suitable modular switch panel or a separate panel.
- Connect the regulator in series with the fan as shown in circuit diagram.
CLEANING/ MAINTENANCE INSTRUCTIONS
- To clean the fan, wipe it with a soft and clean cloth,
- Do not apply pressure on the blades in order to prevent them from bending.
- If serviving is required, refer only to a qualified electricain.
- For oiling use ALFA ZN 320 oil and for greasing use SHELL RL 3 grease.
DISPOSAL
Do not dispose of electrical fans/accessories (including packing materials) as unsorted municipal waste, use separate collection facilities. Contact. If these are disposed of in landfills or dumps, it may affect enviroment adversely.
WARNING:
Users are not supposed to replace other than Orient spare parts in Orient
product in case of any defect and must be serviced through Orient authorised
service centre only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>