behringer BB 560M High-Quality Professional Headphones with Built-in Microphone User Guide
- June 5, 2024
- Behringer
Table of Contents
Quick Start Guide
BB 560M
High-Quality Professional Headphones with Built-in Microphone
Controls and Connectors
- VOLUME + / NEXT SONG – Press quickly to increase the volume, press and hold to skip to the next song.
- PLAY/PAUSE – Used for several functions including Bluetooth pairing, play, pause, hang up, refuse the call, and redial. Hold this button for 1 second to turn the headphones on.
- VOLUME – / PREVIOUS SONG – Press quickly to decrease volume, press and hold for the previous song. (4) 3.5 mm INPUT – Connect a 3.5 mm stereo cable for wired audio use.
- LED – Red and blue status indicator light.
- MICROPHONE
- USB PORT – Micro USB port for charging.
Charging
After unpacking the headphones, the USB charging cable should be plugged in
and allowed to charge for at least 4 hours. Once the battery has been fully
charged the first time, subsequent charges should only take 2-3 hours. While
charging, the LED will light red. After the battery has reached full capacity,
the LED will turn off.
The headset will beep twice to indicate that the battery power is low, and the
LED will flash red. When the voltage drops below 3 V, the headset will
automatically power off and must be recharged.
The pairing of the headset and Bluetooth device
- Turn on the headphones by holding the Play/Pause button for 1 second. The LED will alternate flashing red and blue and a sound will beep twice to indicate that the device is ready for pairing.
- Open the Bluetooth menu on your Bluetooth device and search for available connections. Note that if the headset does not successfully pair with a device, it will automatically power down after 3 minutes.
- Select “BB 560M” from the list. When pairing is successful, the headset will beep once and the LED will light blue. If a password is required, use “0000”.
Once the headset has been successful pair with another device, it will automatically try to connect to this same device when the headset is powered off and powered on again.
Bluetooth wireless call
When the Bluetooth headset is paired and connected with your mobile phone, you
can use the headset to accept phone calls in addition to listening to music.
Outgoing calls
- To make a new call while using the headset, dial a number as usual. A ringing tone will be heard in the headset and the voice audio and microphone will automatically be switched to the headset. (note that some phones require the switch to be confirmed manually on the screen)
- To redial the last number, double click the Play/Pause button to dial out the last dialing phone number. (Some mobile phones may only require a single press of the button.)
Answering and hanging up calls
- When the phone rings, press the Play/Pause button once or press the phone answer key to answer the phone.
- To reject the call, press and hold the Play/Pause button for 1 second.
- To end a call, press the Play/Pause button or press the hang-up button on the phone screen. After the call ends, any music that was playing prior to the call will resume.
IMPORTANT SAFETY INFORMATION
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not throw this product in the fire, to avoid explosion.
- Do not expose this product to bright sunshine for a long time.
- Do not disassemble or modify this product.
- Please store this product in a clean and dry environment.
Specification
Version | Bluetooth V5.0 |
---|---|
Frequency range | 2.402 – 2.480 GHz ISM Band |
Wireless transmission standard | Class 2 |
Channel | 79 channels of 1 MHz bandwidth |
Connection type | Point-to-point |
Transmitting range | 10 m (free space) |
Frequency response | 20 Hz – 20 kHz |
Signal to noise ratio | 80 dB |
Audio power output | 2 x 10 mW |
Status indication | Red and blue bi-color indicator light |
Applicable pairing product | USB Bluetooth adapter, Bluetooth mobile phone, |
iPad, MID, etc in accordance with HFP, HSP, A2DP, AVRCP Bluetooth protocols
Support decoder| SBC/MP3/ACC
Battery| Polymer lithium-ion battery 3.7 V, 185 mAH
Charging time| 2-3 hours
Charging power supply| Computer USB 5 V; charger with output DC 5 V 300 mA
Operating time| Up to the 7 hours after fully charged
To prevent possible hearing damage, do not listen at high volume levels for
long periods. As a guide to setting the volume level, check that you can still
hear your own voice when speaking normally while listening with the
headphones.
** Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
WARNING**
- Don’t replace a battery that can defeat a safeguard;
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and
- A battery is subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- Attention should be drawn to the environmental aspects of battery disposal.
FEDERAL COMMUNICATIONS COMMISSION
COMPLIANCE INFORMATION
Behringer
BB 560M
Responsible Party Name: | Music Tribe Commercial NV Inc. |
---|---|
Address: | 5270 Procyon Street, Las Vegas NV 89118, United States |
Phone Number: | +1 702 800 8290 |
FCC ID: QWH-MTP
BB 560M
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music
Tribe can void the user’s authority to use the equipment.
FCC RF Radiation Exposure Statement:
Caution! The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment.
Such modifications could void the user authority to operate the equipment.
1. This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator and
your body.
Hereby, Music Tribe declares that this product is in compliance with
Directive 2014/53/EU, Directive 2014/30/EU, Directive 2014/35/EU, Directive
2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation
519/2012 REACH SVHC and Directive 1907/2006/EC. Full text of EU DoC is
available at https://community.musictribe.com/ EU Representative: MUSIC
Tribe Brands DK A/S Address: Ib Spang Olsens Gade 17 Lisbjerg, DK – 8200
Aarhus N, Denmark UK Representative: Music Tribe Brands UK Ltd Address: St
George’s House 215-219 Chester Road, Manchester, Greater Manchester, England,
M15 4JE We Hear You
Documents / Resources
|
behringer BB 560M High-Quality Professional Headphones with Built-in
Microphone
[pdf] User Guide
BB 560M, High-Quality Professional Headphones with Built-in Microphone,
Professional Headphones, Headphones
---|---
|
behringer BB 560M High Quality Professional Headphones with Built In
Microphone
[pdf] User Guide
BB 560M High Quality Professional Headphones with Built In Microphone, BB
560M, High Quality Professional Headphones with Built In Microphone,
Professional Headphones with Built In Microphone, Headphones with Built In
Microphone, Professional Headphones Microphone, Microphone
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>