behringer UV300 Classic Ultra Vibrato Effects Pedal User Guide
- June 5, 2024
- Behringer
Table of Contents
behringer UV300 Classic Ultra Vibrato Effects Pedal User Guide
Thank you for showing your confidence in us by purchasing the BEHRINGER ULTRA VIBRATO UV300. This high-quality effects pedal delivers the classic pitch modulation and dimensional vibrato effects of the ‘60s and ‘70s. Its comprehensive controls allow you to tailor the UV300 performance right for your needs.
Controls
-
The MODE switch changes the functionality of the effects pedal footswitch. When set to LATCH , the effect will be activated/ deactivated by pressing the pedal once. When set to UNLATCH , the effect will only be active if you depress the pedal. The BYPASS
mode can be selected when no vibrato effect is required. The input signal remains uneffected even if the pedal is depressed. -
The RISE control adjusts the time needed for the effect to reach its maximum detuning. Modulation sets in more slowly when it is turned clockwise.
-
The RATE control determines the speed of the vibrato effect.
-
The DEPTH control adjusts the intensity of the pitch modulation effect.
-
The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator.
-
Use the footswitch to activate/deactivate the effect.
-
Use this 1/4″ TS IN connector to plug in the instrument cable.
-
The 1/4″ TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover.
To install or replace the 9 V battery (not included), press the hinges with a
ballpoint pen and remove the pedal cover. Be careful not to scratch the unit.
The UV300 has no on/off switch. As soon as you insert the plug into the in connector, the UV300 is on. When not in use, remove the plug from the in connector. This extends the life of the battery.
The SERIAL NUMBER is located on the bottom.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
Limited Warranty
Please register your new Behringer equipment right after your purchase by visiting http://behringer.com and read the terms and conditions of our warranty carefully.
Specifications
Behringer is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown.
Music Tribe accepts no liability for any loss which may be suffered by any
person who relies either wholly or in part upon any
description, photograph, or statement contained herein. Technical
specifications, appearances and other information are subject to change
without notice. All trademarks are the property of their respective owners.
Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound,
TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston
Microphones, Aston Microphones and Coolaudio are trademarks or registered
trademarks of Music Tribe Global Brands Ltd.
© Music Tribe Global Brands Ltd. 2021 All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Behringer
ULTRA VIBRATO UV300
Responsible Party Name: Music Tribe Commercial NV Inc.
Address: 5270 Procyon Street, Las Vegas NV 89118, United States
Phone Number: +1 702 800 8290
ULTRA VIBRATO UV300
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
We Hear You
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>