behringer HD300 Heavy Metal Distortion Effects Pedal User Guide
- June 5, 2024
- Behringer
Table of Contents
behringer HD300 Heavy Metal Distortion Effects Pedal
Thank you for showing your confidence in us by purchasing the Behringer HEAVY DISTORTION HD300. This high-quality effects pedal enables you to produce super thick, tube-like distortion plus endless sustain. Thanks to its high- performance features you can achieve the typical hard rock or heavy metal distortion sounds, when playing over a clean amp channel.
Controls
(1) The LEVEL control adjusts the output level.
(2) The TONE control allows you to shape your overall sound.
(3) The BOTTOM control allows you to boost/cut the low-frequency range.
(4) The DIST(ortion) control adjusts the amount of distortion.
(5) The GAIN BOOST control adjusts the gain for more extreme distortion
sounds.
(6) The ON/BATT LED illuminates when the effect is activated. It also
serves as a battery level indicator.
(7) Use the footswitch to activate/deactivate the effect.
(8) Use this ¼” TS IN connector to plug in the instrument cable.
(9) The ¼” TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included). The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit.
The HD300 has no on/off switch. As soon as you insert the
plug into the in connector, the HD300 is on. When not in use, remove the
plug from the in connector. This extends the life of the battery.
The SERIAL NUMBER is located at the underside.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
Warranty
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Specifications
In
Connector| 1/4″ TS
Impedance| 500 kΩ
Out
Connector| 1/4″ TS
Impedance| 1 kΩ
Power Supply
| 9 V , 100 mA regulated
Behringer PSU-SB
USA/Canada| 120 V~, 60 Hz
China/Korea| 220 V~, 50 Hz
U.K./Australia| 240 V~, 50 Hz
Europe| 230 V~, 50 Hz
Japan| 100 V~, 50 – 60 Hz
Power connector| 2 mm DC jack, negative center
Battery| 9 V type 6LR61
Power consumption| 30 mA
Physical/Weight
Dimensions (H x W x D)| approx. 2 1/8 x 2 3/4 x 4 4/5″
approx. 54 x 70 x 123 mm
Weight| approx. 0.73 lbs / 0.33 kg
Behringer is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those listed or shown.
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Behringer
HEAVY DISTORTION HD300
Responsible Party Name:
Music Tribe
Commercial NV Inc.
Address:
5270 Procyon Street, Las Vegas NV 89118, United States
Phone Number:
+1 702 800 8290
HEAVY DISTORTION HD300
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with
Directive 2014/30/EU,
Directive 2011/65/EU and Amendment 2015/863/EU,
Directive 2012/19/EU, Regulation 519/2012
REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark