SAMSUNG MCR-SMD Motion Detection Sensor User Manual
- June 5, 2024
- Samsung
Table of Contents
SAMSUNG MCR-SMD Motion Detection Sensor
Safety Information
This manual explains how to install a Motion Detection Sensor (MDS) kit onto an indoor unit and how to use it. Please read this manual thoroughly before installing and using the MDS Kit.
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
WARNING
Contact a qualified installer or a service center for the installation.
When detaching or disposing of an MDS Kit, contact a qualified installer or
a service center.
Failing to do so may result in electric shock, fire, explosion, problems with
the product, or injury and may also void warranty on the installed product.
Install an MDS Kit securely in a designated place, using the installation
accessories.
If the MDS Kit is not installed securely, the component might fall off and get
damaged.
Do not attempt to repair, disassemble, or modify the appliance yourself.
Failing to do so may result in product malfunction, electric shock, or fire.
So when repairing the product, contact a qualified installer or a service
center.
Operation
Turning the MDS Kit on or off
Using wired remote control
Press the MDS button on the wired remote control to turn the MDS Kit on or off.
NOTE
The wired remote control must be installed together with the indoor unit.
| MDS Button Click | Once | Twice | Three times |
|---|---|---|---|
| Display | Indirect | Direct | – |
| Standard Mode | MDS On (only Turn off the set) | MDS Off | |
| Premium Mode | Indirect Flow Control | Direct Flow Control | MDS Off |
Using wireless remote control
| Option Selection | Indirect | Direct | No Selection |
|---|---|---|---|
| Standard Mode | MDS On (only Turn off the set) | MDS Off | |
| Premium Mode | Indirect Flow Control | Direct Flow Control | MDS Off |
NOTE
- In the Standard mode, Indirect/Direct is displayed on the wireless remote control, but does not operate.
- The Indirect/Direct function is supported only in the Premium mode.
Setting the MDS Kit installation option
Set SEG23, the MDS Kit installation option of the indoor unit where the MDS Kit is installed, to the desired value with referring to the table below.
| Function | SEG23 | Soft Off + Hard off | SEG23 | Soft Off only |
|---|---|---|---|---|
| 0 | Disuse |
Standard
| 1| Off after 20 min. (from the last motion detection)| 7| Off after 20 min.
2| Off after 40 min.| 8| Off after 40 min.
3| Off after 80 min.| 9| Off after 80 min.
Premium
| 4| Off after 20 min.| A| Off after 20 min.
5| Off after 40 min.| B| Off after 40 min.
6| Off after 80 min.| C| Off after 80 min.
SOFT OFF: The indoor unit turns off its operation at the indicated time
in the table for Installation Option after its final
motion detection. But, it turns on again if the MDS detect motion.
HARD OFF: Designated time after SOFT OFF, it cannot turn on automatically
when it detect motion. Users should control to
turn on the indoor unit with remote controller, etc.
NOTE
- Detectable MDS area: 6 m radius at 2.7 m height.
- When the air conditioner supports the Wind-Free Cooling function, it operates the Wind-Free Cooling function automatically before the air conditioner turns off.
- If it happens repeatedly that the MOS Kit turns the air conditioner off and on, the kit reduces the time taken until the air conditioner is turned off for energy efficency
- In the Standard mode, you can only turn on/off the air conditioner.
- In the Premium mode, you can also operate the functions such as turning on/off the air conditioner, comfort temperature and comfort saving controls.
- The MDS sensor may detect other heat sources, not humans, and perform the MDS functions.
| MDS Button Click | Once | Twice | Three times |
|---|---|---|---|
| Standard | Turn on | Turn off | – |
| Premium | Indirect Flow | Direct Flow | Turn Off |
Samsung comfort control features
The following Samsung comfort control features are activated when SEG23, the MDS Kit installation option of the indoor unit, is set to the Premium mode. For more information about the MDS Kit installation option, see Setting the MDS Kit installation option on page 7.
- Indirect Flow: When the MDS Kit detects motion, it moves the air flow blades to prevent the breeze from blowing directly toward the specified areas (locations where humans are).
- Direct Flow: When the MDS Kit detects motion, it moves the air flow blades to send the breeze directly toward the specified areas (locations where humans are).
- Comfort Temperature: When the temperature difference between the upper part and lower part of a room is significant, the MDS Kit moves down the air flow blades to mix airs and consequently to reduce the temperature difference.
- Comfort Saving: The MDS Kit detects motion in the room and controls the set temperature (up to the amount of +2°C for cooling, -2°C for heating) to reduce electricity consumption.
Operation troubleshooting
- If the MDS Kit has a connection problem or malfunction, the MDS Kit error E143 is indicated on both the panel display and the wired remote control.
- Although the MDS Kit error occurs, the indoor and outdoor units normally operate without the MDS Kit functions.
- If the MDS Kit error persists, check the wire connection and contact a service center.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>