behringer ZMX8210 Ultrazone Rackmount Zone Mixer User Guide

behringer ZMX8210 Ultrazone Rackmount Zone Mixer

Important Safety Instructions

Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installations or modifications should be performed only by qualified personnel. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user-serviceable parts inside. Refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus. These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories specified by
    the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.

18. Do not install in a confined space, such as a book case or similar unit.

19. Do not place naked flame sources, such as lighted candles, on the apparatus.

20. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.

21. Use this apparatus in tropical and/or moderate climates.

LEGAL DISCLAIMER

MUSIC Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and COOLAUDIO are trademarks or registered trademarks of MUSIC Tribe Global Brands Ltd. © MUSIC Tribe Global Brands Ltd. 2018 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC Tribe’s Limited Warranty, please see complete details online at musictri.be/warranty.

Controls

The controls of channels 1 – 6 and 7 – 8 are largely identical as well as the controls of the LEFT, RIGHT and AUX buses. Channels 1 and 7 plus the LEFT bus are described exemplarily. Pressing the switch controls, unless otherwise noted, activates the described functions, but are deactivated when not pressed.
Channels 1 – 6

1. PAD: The switch attenuates the input level of loud signal sources by 20 dB.
2. +48 V: The switch activates the phantom power for capacitor microphones.
3. L, R, AUX: The three switches route the channel signals to one or more output buses.
4. THRESH (only Channel 1): The knob selects the level at which the signal is muted. When the level of the input signal exceeds the specifi ed value, the signal of channels 2 – 8 on the LEFT/RIGHT bus is muted. Apply the Mute function to fade out music signals as soon as a microphone on channel 1 is talked into.
5. LEVEL: This knob adjusts the preamplifier cation and the level with which the input signal is sent to the selected buses.
6. LEDs: The LEDs show the input levels. When the CLIP LED lights up, the input level needs to be attenuated by using the LEVEL knob (5) to prevent clipping. In case the attenuation is insu ffi cient, use PAD switch (1) to attenuate the signal further.
7. MONO: This switch selects the configuration of the stereo channels:
   • In mono mode (switch pressed), the channel’s L/R inputs are mixed together and sent to the LEFT, RIGHT and AUX buses. In this way, a mono signal is sent to all output buses at the same time.
   • In stereo mode (switch not pressed), the signal of the L input is sent to the LEFT bus, the R input is sent to the RIGHT bus and a mixed L/R signal is sent to the AUX bus.
8. LEDs: These have the same function as the control (6). In stereo mode, the LEDs show the summed level of the input signals L and R.
9. LEVEL: This has the same function as the control (5). In stereo mode, the control adjusts the volume level of the L/R signal.
10. CH SELECT: This switch is used either to activate channel 7 or 8. The active channel is indicated by the glowing of the corresponding LED.
11. MIC LOW CUT: This switch cuts low-frequency rumble below 100 Hz
12. MIC MIX: This switch removes the signal of channels 1 – 6 from the remote control function, allowing only the output volume of channels 7/8 on the LEFT/RIGHT bus to be remote controlled. When the switch is not pressed, the total volume of all channels fed to the LEFT/RIGHT bus is remote controlled.
13. RIGHT MUTE: This switch excludes the RIGH when using the RIGHT and LEFT buses for different zones (rooms).
    • When the switch is pressed, the signal of channels 1 – 8, which is dependent on the signal level of channel 1, is muted on both the LEFT and RIGHT bus. This occurs when the input level of channel 1 drops below the specified threshold value (THRESH (4) ).
    • When the switch is not pressed, only the LEFT bus is muted while the RIGHT bus continues to transmit a signal, provided the individual channels have been routed accordingly.
14. EQ ON: The switch activates the equalizer (15) for the LEFT and RIGHT bus.
15. LOW/LOW MID/HIGH MID/HIGH: This knob adjusts the boost/cut of factory-preset frequencies as follows:
    • LOW: This boosts/cuts frequencies below 70 Hz by a maximum of ±15 dB.
    • LOW MID: This boosts/cuts frequencies around 300 Hz by a maximum of ±15 dB.
    • HIGH MID: This boosts/cuts frequencies around 3 kHz by a maximum of ±15 dB.
    • HIGH: This boosts/cuts frequencies above 10 kHz by a maximum of ±15 dB.
16. LEDs: When the CLIP LED lights up, attenuate the output level by using the LEVEL knob (17) to avoid clipping.
17. LEVEL: This knob adjusts the output level of the bus outputs OUT L, OUT R and AUX.
18. POWER: The POWER switch powers up the  mixer. The POWER switch should be in the Off position when connecting the unit to the mains.
19. IEC power receptacle: The connection to the mains is established through an IEC connector. It meets all of the international safety certifi cation requirements. A fi tting power cord is included.
20. REMOTE: This connector is used for connecting components to remote control the ZMX8210.
    • It is possible to connect a simple potentiometer to remote control the volume of the LEFT and RIGHT buses (see Chapter 3.1.3).
    • Connect a push-button switch and two control diodes to remote control the CH SELECT switch (10) of channels 7 and 8 (see Chapter 3.1.3).
21. BUS LINKS: Use this connector to link two ZMX8210s together to provide additional inputs (signals). The three output buses LEFT/RIGHT/AUX are linked together using the connector. The mute signal of the ZMX8210 which is set to be the master is also transmitted so that the mute function of the master is also able to mute the buses of the slave.
22. SLAVE/MASTER: The switch places the ZMX8210 in the master or slave mode of operation.
    • is pressed, the ZMX8210 is placed in the slave mode of operation.
    • is not pressed, the ZMX8210 is placed in the master mode of operation.
23. AUX/OUT R/OUT L: Balanced signal outputs for buses AUX, RIGHT and LEFT.
24. INPUTS 7 – 8: Unbalanced signal inputs for channels 7 – 8. The connections are RCA connectors.
25. INPUTS 1 – 6: Balanced signal inputs for channels 1 – 6.

Specifications

Other important information

1. Register online. Please register your new MUSIC Tribe equipment right after you purchase it by visiting behringer.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and effi ciently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your MUSIC Tribe Authorized Reseller not be located in your vicinity,
   you may contact the MUSIC Tribe Authorized Fulfi ller for your country listed under “Support” at behringer.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at behringer.com. Alternatively, please submit an online warranty claim at behringer.com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

ULTRAZONE ZMX8210
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Tribe can void the user’s authority to use the equipment.

References

• Behringer | Home
• Music tribe – Music is life

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>