ELIJAH Invert-A-Bolt Metric Fastener Instruction Manual
- June 3, 2024
- ELIJAH
Table of Contents
ELIJAH Invert-A-Bolt Metric Fastener
Your
Elijah Tooling, Inc. Invert-A-Bolt™ (IVB) fastener has been manufactured to
provide low cost, high value performance combined with ease of use. The IVB
fastener is a patented product, ideal for connecting two materials or objects
together especially when an unobtrusive connection is desired. The IVB
fastener features finishes that improve appearance and reduce rust as well as
providing closely held tolerances on threads and internal dimensions to insure
that it meets your exacting expectations.
OPERATING INSTRUCTIONS
Usage of your IVB fastener requires simple preparation of the “holding” side for the housing threads and preparation of the “receiving” side for the stud threads. For Flush Mount:
-
Prepare the “holding” side in the following manner:
Drill a 8 mm diameter (thru) hole (optional) C’Bore 12 mm x .237 mm R (max) to a depth of 34.5 mm Tap (or Thread Mill) M14X2 6H LH to a depth of 29 mm -
Prepare the “receiving” side for the stud threads:
Drill 5mm diameter thru. C’sink 9mm dia. x 45 degrees. Tap Drill 6.8mm
approximately 12mm deep. Tap M8x1.25 6H 10mm deep.
For better resistance against vibration,
use a Spiralock® tap. Once the “holding” side and the “receiving” side have
been prepped, simply screw your IVB fastener into the M14x2 threaded hole with
a 10mm hex wrench. Place the “receiving” side M8x1.25 tapped hole directly
above the IVB fastener. Reach through the 5mm hole with your hex head wrench
until contacting the 4mm hex head broach in the IVB stud. Start turning
counter-clockwise lifting your hex head wrench at the same time. The stud will
proceed into the M8x1.25 tapped hole. Tighten until the stud is fully engaged
(approximately 8mm into the “receiving” side). Use a feeler gauge to insure
that the “receiving” side material is pulled down properly.
REPLACEMENT PARTS & MAINTENANCE
Periodically remove IVB fastener, disassemble by removing the retaining ring
in the base of the product, blow out the IVB fastener to clean out accumulated
metal chips and debris. Reassemble. Reinstall. If necessary, IVB-
M8x1.25-031RFB Refurbishment Kit is used to replace the internal components of
the IVB fastener. Cross section of IVB fastener with hex wrench
LIMITED WARRANTY
We warrant that within 90 days from the date of shipment, if the product
manufactured by us and sold by us (or an authorized distributor) is in the
possession of the original buyer, we will replace or repair, at our option,
free of charge, any part or parts which upon examination are found to be
defective in workmanship or material, and not due to normal wear, provided
that, upon our request, the product or parts thereof are returned to our
location, with accompanying documentation that the product has been installed,
used and maintained in accordance with instructions and has not been subject
to abuse. We shall not be liable or responsible for any expense or liability
for repairs, additions, or modifications made upon the product without our
written consent. This warranty is in lieu of all other express or implied
warranties (including without limitation any warranty of merchantability or
fitness for a particular purpose.) In no event shall we be liable for any
indirect, special, or consequential damages (including, but not limited to,
lost profits or other damages from loss of production) caused by defective
material, or by unsatisfactory performance of the product, or by any other
breach of contract by us.
The Elijah Tooling, Inc. Warranty shall apply in all cases to all products
manufactured by us and sold by us. Elijah Tooling, Inc. reserves the right to
modify or change the design of products shown in this
specification/instruction sheet, without notice. Such modifications or changes
may include, but are not limited to, changes in finish, materials,
specifications, etc., from descriptions and illustrations of products listed
herein.