Shan Tou Subo Techtoy 2A4PA-BGSUBO Toys Car Instructions

Shan Tou Subo Techtoy 2A4PA-BGSUBO Toys Car

SAFETY PRECAUTIONS

• It is a radio control model, not a toy!
• In order to enjoy running the car, you need to finish assembly before operation. Do routine maintenance work after operation. Replacement parts and option parts are available separately.
• Improper usage with Alkaline cells or rechargeable batteries may damage the electronics for the car or the radio.

WARNINGS

Please follow the points as below in order to prevent accidents from happening to the car and people.

• Be sure to read thoroughly the manual before you begin. Fresh users should seek advice from people having rich experience in order to assemble the model correctly.
• As the product contains small and sharp parts, assemble and store this product only in places out of the reach of children.
• Never reverse connection/disassemble the battery. This may lead to damage and leakage.
• Do not operate the model on public roads, in crowded places and near infants as it may cause accidents.
• Cutters, nippers and screwdrivers need careful handling.
• Painting must be done only in a well-ventilated area.
• When the model is not in use, always turn off the receiver and transmitter. Furthermore, disconnect the batteries and remove them from the model and the transmitter. This may be dangerous such as overheat and leakage.
• Do not expose this model to high temperature, humidity or direct sunlight.

OPERATING YOUR MODEL SAFELY

• Operate your model in spacious areas ONLY with few people around! Do not operate it:
  1. On road!
  2. In places where children and many people gather!
  3. In residential districts and parks!
  4. Indoors and in limited space! Non-observance may result in personal injury and property damage!
• Always check the radio batteries With weak dry batteries, transmission and reception of the radio would fall off. You may lose control of your model in such conditions. This may also cause serious accidents!!
• Keep in mind that people around you may also operate the radio control model! NEVER share the same frequency with somebody else at the same time! Otherwise, Radio signals will be mixed up and you will lose control to your model. This may lead to accidents.
• The car must stop immediately and check for the reasons why it is operating abnormally. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents!
• The safety of battery:
  1. Exhaust batteries should be safely disposed of!
  2. Non-rechargeable batteries are not to be recharged, there is danger of explosion!
  3. Do not throw the of battery into a fire! There is a danger of an explosion!
  4. Do not swallow the battery!
  5. Store only in cool, dry, and dark places and should be kept out of the children!
  6. When the battery leaks the liquid and lets it into your eyes, please right away rinse them and consult an ophthalmologist.
• Do NOT put fingers or any objects inside rotating and moving parts!
• Right after use, do NOT touch the motor! The danger of burning yourself!

CONTENTS

• Transmitter
• Body(To the actual product)
• Chassis(To the actual product)
• 7.4V 1500 mAh Large power Li-Po battery
• Cross Wrench(small)
• Screwdriver
• Instruction manual

ABOUT THE RADIO

1. Frequency Description: First, turn on the remote control model car power switch press the button for frequency bind and then switch on the transmitter. If the frequency bind is successful, the server will make a sound.
2. Accept the machine plug schematic.

Transmitter function introduce

Our company has been configured a new-style transmitter for model car. Please read the instruction manual carefully. The following is the transmitter’s description of all functions.

Assembly of the transmitter battery

1. Remove the battery lid.
2. Load 3 AA-size alkaline batteries as shown in the illustration. Caution: install batteries with the correct polarity.
3. Replace the lid as shown.

Model battery’s charging and assembly

1. Charge
2. The first transformer charging port is connected to the rechargeable battery plug. Then the adapter plugs into an electrical outlet. The charge time is 3-4 hours.
3. Disconnect the charger plug after the charge.
4. Open the battery cover lid
5. Installing battery

4WD batholith parts assembly diagram

Spare parts list of high-speed vehicles

• Front shock absorption bridge
• Rear shock absorption bridge
• Bottom front bumper bracket
• Side bar of the chassis
• Bottom rear bumper bracket
• Cover lid of the bottom battery
• Battery knob lock catch
• Upper covering of the circuit board
• Swing arm
• Vehicle bottom
• Front connecting rod
• Rear connecting rod
• Steering connecting rod
• Rudder connecting rod
• Upper shell of the front differential case
• The protective covering of the motor
• Left shell of the rear gearbox
• Right shell of the rear gearbox
• Bottom shell of the front differential case
• Steering stop
• Rear wheel seat
• C-shape seat
• Shock regulation ring (small)
• Shock regulation ring (medium)
• Shock regulation ring (large)
• Anti-vibration medial axis
• Principal anti-vibration part
• Upper sleeve of the spring
• Lower sleeve of the spring
• Shock absorption plug
• Top cover
• Small bevel gear
• Cross
• Hexagon wheel seat
• Cross universal joint
• Drive connecting cup
• Driven bevel gear
• Motor gear
• Driving gear of the front differential case
• Driving gear of the rear differential case
• Connectors of the front swing arm
• Connectors of the rear swingarm
• Driven gear of the rear differential case
• Driven gear of the front differential case
• Rudder fasteners
• Steering pressed parts
• Clutch race
• Shell of the differential case
• Rudder arm
• T-shape bearing
• Steering connect bridge
• Speed reduction gear
• Clutch sleeve
• Clutch retaining ring
• Front anti-collision frame of the short-course truck
• Rear anti-collision frame
• Rear anti-collision strut
• Front lamp cover
• Left protective cage
• Right protective cage
• Front roof rack
• Rear tire rack
• Roof rack
• Light bar cover
• Top strap
• Spare tire seat
• Light bar adapter
• Booth seat
• Large lamp holder
• Front bumper
• Mini light bar
• Rear bracket
• Large lamp cover
• Rear cover of the left lamp
• Rear cover of the right lamp
• Hub
• Left wheel skin
• Right wheel skin
• Top board
• Seat plate
• Front Panel
• Left side panel
• Right side panel
• 2.0X4 Flat head screw
• 2.0X7 Countersunk head screw
• 2.0X9 Countersunk head screw
• 2.5X6 shell 6 Non-self-tapping
• 2.6X5 Countersunk head screw
• 2.6X5 Flat head screw
• 2.6X7 Flat head screw
• 2.6X8 Flat head screw
• 2.6X10 Countersunk head screw
• 2.6X10 Flat head screw
• 2.6X12 Flat head screw
• 2.6X14 Countersunk head screw
• 2.6X14 Flat head screw
• 2.6X16 Half thread screw
• 3.0X24 Half thread screw
• 3.0X6 Non-self-tapping screw
• Hexagon socket shot screw
• Ball head screw
• T head step screw
• 2.0X6 Flat head screw
• 2.0X10 Flat head screw
• 4.0X16 Non-self-tapping screw
• 1.2X7.5 Optical shaft
• 1.5X7.5 Optical shaft
• 1.5X10 Optical shaft
• 4.0X33 Knurling shaft
• 4.0X35 Steel pipe
• 3.0X54.50 Optical shaft
• R-shape lock catch
• 3X41.5 Shaft screw
• Shock absorption pressure spring
• Clutch pressure spring
• 4.8X6.8 Ball head sleeve
• Flange nut
• 4X7X2mm Ball bearing
• 5X9X3mm Ball bearing
• 7X11X3mm Ball bearing
• 1OX15X4mm Ball bearing
• Motor cooling fin
• Front and rear driveshafts
• 390 Motor
• Switch
• Rudder
• Rudder swing arm
• 18650 battery
• Blast-off electric plate
• Incept electric plate
• Shock absorption assembly
• Transmitter
• Components of the front differential case
• Components of the rear differential case
• 1513 case components
• Multi-link independent suspension components
• Left tire components
• Right tire components

WARNING
Choking hazard! This product contains small parts. NOT suitable for children under 3 years. Contains electrical components and should be kept dry at all times. Regularly check the battery charger wires, plugs and shell and other components for damage. DO NOT use if any part is damaged.

1. Detachable small parts should be stored safely and out of reach of children.
2. If interference is experienced, turn the model off and try it again in a different area.
3. Remote control will not function correctly if the batteries are low. Please replace the batteries.
4. Please discard old/used batteries in a safe manner. Consider your environment!
5. Please store the remote control in cool, dry place.
6. DO NOT expose to fire or high temperatures, moist storage.
7. Should the battery get wet, wipe immediately with a soft dry cloth. If transformed, please stop usage.

Battery use caution proceeding

1. The bodywork uses a set of Li-Po 7.4V rechargeable batteries.
2. Remote control uses 3 x 1.5V ‘AA’ batteries.
3. Please pay attention to correct polarity when replacing batteries.
4. Rechargeable batteries should be charged under adult supervision.
5. DO NOT use a mix of old and new or different types of battery.
6. After the battery is exhausted, the model should be removed.
7. DO NOT short circuit any terminals.
8. DO NOT attempt to recharge non-rechargeable batteries.
9. Remove batteries from the model when recharging.
10. DO NOT put batteries into a fire or into water.
11. The rated input voltage battery charger MUST be suitable for your mains power voltage.
12. During charging it is quite normal for the charger and batteries to heat up.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:
Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>