MORRIS GRB-410 Liters ABSORPTION REFRIGERATOR User Manual
- June 5, 2024
- MORRIS
Table of Contents
GRB-410 Liters ABSORPTION REFRIGERATOR
GRB-410
ABSORPTION REFRIGERATOR
INTRODUCTION
Thank you for purchasing our absorption refrigerator. This unit is designed to
improve your living and entertaining comfort. The absorption system
refrigerator is a compact, totally silent refrigerator that uses no
compressors or fans. Originally developed for commercial use or similar use.
With its silent operation and attractive design, you will enjoy the
convenience and comfort for years to come. Please read these instructions
carefully before operating this appliance. When using this appliance, always
exercise basic safety precautions. This easy-to-use manual will guide you to
getting the best use of your absorption refrigerator.
REFERENCE INFORMATION
Please complete the following information for future reference. You will need
it to obtain warranty service.
Model Name: __
Serial Number : __
Date of Purchase: __
Place of Purchase: _____
*The above information is written on the back of the unit. Retain this Owner’s Manual with your sales receipt as a
permanent record of your purchase.
TABLE OF CONTENTS
PAGE
Introduction ………………………………………………………………………….. 2
Reference Information ……………………………………………………………… 2
Important Safety Precautions……………………………………………. ……… 3
Installation ………………………………………………………………………………. 4
Product Parts and Features ………………………………………………………… 5
How to Operate………………………………………………………………………. 5
Absorption refrigerator Care and Cleaning ……………………………………….. 6
Limited Warranty …………………………………………………………………… ..6
Environmental Protection……………………… ……………………………………6
Reversing The Door (Option)……………………………………………. … …… …7
Circuit Diagram ……………………………………………. …………….. …… …..7
Slider installation instruction……………………………………………… …………8
2
IMPORTANT SAFETY PRECAUTIONS
Before you use your absorption refrigerator, please read this instruction
manual carefully. Use this appliance only for its commercial purpose as
described in this ownerÿs manual. This absorption refrigerator must be
properly installed in accordance with the installation instructions before it
is used. Never unplug you absorption refrigerator by pulling on the power
cord. Always grasp the plug firmly and pull straight out from the wall outlet.
- Repair or replace immediately, all electric service cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length, the plug or the connector end. 2) Unplug your absorption refrigerator before cleaning or before making any repairs. NOTE: If for any reason this product requires service, we strongly recommend that a certified technician perform the service. 3) Do not operate your absorption refrigerator in the presence of explosive fumes. 4) The power supply must be properly grounded. 5) Do not use an adapter plug or extension cord. 6) Do not use the unit in the immediate surroundings of a bath, shower or swimming pool.
- Before discarding or storing, we recommend that you remove the door and
leave the shelves in place. This will reduce the possibility of danger to
children. 8) Do not store food in absorption refrigerator as the interior
temperature may not be cool enough to prevent spoilage. 9 The instructions
concerning persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge and children playing
with the appliance are not required. 10) If the power supply is damaged, it
must be replaced by the manufacturer, its service agent or similar qualified
persons in order to avoid a hazard. 11) Do not try to fix the lamp and open
the back guard, refer to agent or manufacture for help. 12) Maximum loading of
each shelf in storage compartment is 8 kg. 13) Maximum loading of door balcony
is 5 kg. 14) Sound pressure level at workstation is far below 70dB. 15) AVOID
CONTACT WITH STRONG OXIDIZING AGENTS.
WARNINGS!
– keep clear of obstruction all ventilation openings in the appliance enclosure or in the structure for buildingin
– Do not use mechanical devices or other means to accelerate the defrosting process,other than those recommended by the manufacturer.
– Do not use any heat sources,such as candles or heaters,to speed up defrosting. – Do not damage the refrigerant circuit. – Do not use electrical appliances inside the food storage compartments of the appliance,unless they
are of the type recommended by the manufacturer
3
INSTALLATION
It is advisable to clean the inside of the absorption refrigerator with
lukewarm water using a mild detergent, and then to dry it thoroughly prior to
use. The temperature in the appliance will depend on: The temperature in the
room The frequency and duration of periods when the door is open. How many
items are in the fridge It may therefore be necessary to adjust the thermostat
from time to time. The refrigeration system of the cabinet is designed to
operate with the cabinet located on a flat surface. Avoid tilting the cabinet
side. If the cabinet must be tilted on an angle for handling or moving
purposes, allow it to sit in an upright position 20 to 30 minutes prior to
plugging it in and starting the cooling of the storage compartment. Grounding
plug and socket should be provided in accordance with local regulations. The
cable-size should meet the refrigerator’s requirements. The unit must be
connected to proper electrical network, which is shown on the nameplate,
through an omnipoplar circuit-breaker. To assure the proper function of the
refrigerator, please observe the following recommended. To ensure the
circulation, the unit should be kept at 12 cm, away from the wall. Locate the
unit away from direct sunlight. This will enable you to obtain the best
performance and save energy. Under no circumstances should the top grid be
covered by any objest. It will preclude the warm air from circulating. 1. Unit
must be installed on an even surface. 2. You must insure that there is a gap
at least 20mm between unit back side and the wall. Under normal installation
there is no need to leave free space from the top and bottom of the unit or
from the sides. 3. Free air flow through cooling system should be insured 4.
Air must have ambient temperature, and it should not be preheated by any
heating source. 5. in case you place any kind of grill on air input or output,
you must insure that a gap of at least 200mm should be available. 6. At the
back of the unit stack effect is created. Cold air is entering from the bottom
of the unit, it is passing through the cooling system and at the nd hot air is
coming out from the upper side of the unit.
Installation Figure
4
PRODUCT PARTS AND FEATURES
Lamp Balcony
Feet
Shelf Installation and use of the accessories as shown in above figure is the
most efficient in terms of energy saving.
HOW TO OPERATE ABSORPTION REFRIGERATOR
1. Insert power plug into wall outlet 2. To adjust the temperature turn
thermostat knob inside the cabinet.
Automatic Defrosting
For models suffix “E” are with automatic defrosting system. For other models
which are with manual defrosting system, you just turn the thermostat knob to
zero position until the accumulated frost meltsthen return to normal position.
Temperature Control
TYPE A: The inner temperature ranges from 2 t o 8 .You can turn the thermostat
knob to select your desired temperature. Setting 1 is the highest temperature
and the setting 6 is the lowest temperature. When you place thermostat to 0
the unit will stop working
TYPE B: The inner temperature ranges from 2 t o 8 .You can turn the thermostat
knob to select your desired temperature. When you place thermostat to OFF the
unit will stop working
5
ABSORPTION REFRIGERATOR CARE AND CLEANING
Warning:To avoid electric shock always unplug you absorption refrigerator
before cleaning. Ignoring this warning may result in injury. General:Do not
use harsh chemicals, abrasives, ammonia, chlorine bleach, concentrated
detergents, solvents or metal scouring pads. Some of these chemicals may
dissolve, damage and/or discolor your absorption refrigerator. 1) Remove the
contents of the appliance 2) Wipe the inside and outside surfaces with a damp
cloth. The addition of vinegar to the water is good for the
prevention of mold and fungus. 3) Wipe all parts thoroughly after the
cleaning. IMPORTANT: When the absorption refrigerator is not in use it must be
completely dry inside to avoid mold growth (if possible have the door open).
6
REVERSING THE DOOR (OPTION)
How to reverse the door ¾ Remove the lower hinge by loosening and removing the
screws with screwdriver. ¾ Carefully lower the door and remove it. ¾ Remove
the two screws from the left top hinge position, take the metal part off the
hinge position. ¾ Remove the two screws from the right top hinge and take off
the hinge, insert the metal part, rivet the two screws
thereafter. ¾ Take off the lower hinge and fix it to the opposite side. ¾ Take
the door. Insert the lower hinge axle into the right bottom hole of the door.
¾ Fix the spare hinge to the left top position of the cabinet. Adjust the
door, make it straight and in alignment with
the cabinet. Note: As the door gasket gets pressed-in during shipment, after
reversing the door the gasket might have to be reset. This will be good for
seal to avoid any air escaping. If there is a gap between the cabinet and the
door gasket, set the gasket by gently pulling it out to seal the gap. If
necessary, you are recommended also to use the hair drier to warm the gasket
to get rid of the gap.
CIRCUIT DIAGRAM
For unit with manual defrosting
XP
LAMP SWITCH
SAT
HT
LAMP
XP Power Supply SAT Temperature Control
HT Heating Tube LAMP
LAMP SWITCH
7
Slider installation instruction (optional part not included in the package)
Part A, mounted to minibar door
Part B, mounted to furniture door
Step 1: Fix Part B onto furniture door with screws. Make sure the thicker end
is be in the outside.
Part B, mounted to furniture door
Step2: Fix Part A onto the minibar door with two screws. Make sure Part A
slides well along Part B.
Part B, mounted to furniture door
Part A, mounted to minibar door
GRB-410
Yes No
Value 560 402 455 282
0
231
10 No
Yes /()9 36
G A
Temperate
32
36
5
A
Notice about recycling
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical
and electronic equipment, at their end-of-life, should be disposed of
separately from your household waste. Please dispose of this equipment at your
local community waste collection/recycling centre. In the European Union there
are separate collection systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
Declaration of Conformity
Herewith, we state that this product, complies with the requirements of below
directives: EMC-Directive: 14/30/EU Low Voltage Directive: 14/35/EC CE Marking
Directive: 96/68/EEC ErP Directive: 09/125/EC ROHS Directive: 11/65/95/EC &
delegated Directive (EU) 15/863 The detailed declaration of conformity can be
found at www.morris.gr
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>