Shark HP200 Series Air Purifier Owner’s Manual

Shark HP200 Series Air Purifier

IMPORTANT SAFETY INSTRUCTIONS

HOUSEHOLD USE ONLY

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

GENERAL WARNINGS

1. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. Unplug or disconnect the appliance from the power supply before servicing.
2. DO NOT operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
3. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. DO NOT route cord under furniture or appliances. Keep cord away from high traffic areas and place cord where it will not be tripped over.
4. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
5. This appliance is not intended for use by anyone (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

USE WARNINGS

6. Children should be supervised to ensure that they DO NOT play with the appliance.
7. Cleaning and user maintenance shall not be made by children without supervision.
8. Prior to cleaning or other maintenance, the appliance must be unplugged from the electrical outlet.
9. DO NOT handle plug or appliance with wet hands.
10. DO NOT use without filter in place.
11. Only use Shark® branded filters and accessories.
12. DO NOT damage the power cord:
    • DO NOT pull or carry appliance by the cord or use the cord as a handle.
    • DO NOT unplug by pulling on cord. Grasp the plug, not the cord.
    • DO NOT stand the appliance on the power cord, close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.
13. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
14. DO NOT use if airflow is restricted. If the air paths become blocked, turn the appliance off and unplug from electrical outlet. Remove all obstructions before you plug in and turn on the unit again.
15. T DO NOT use if appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
16. DO NOT place appliance on unstable surfaces such as chairs or other furniture.
17. DO NOT use in the following areas:
    • Wet or damp surfaces
    • Outdoor areas
    • Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)
18. Turn off all controls before unplugging the appliance.
19. Unplug from electrical outlet when not in use and before any maintenance or cleaning.
20. Hand wash with soapy water only. Washing with cleaning chemicals could damage the unit.
21. Make sure filter is in place after routine maintenance.
22. Not suitable for use with solid-state speed controls.

REMOTE BATTERY

23. Dispose of coin cell batteries according to local regulations. Keep batteries away from children at all times. Even used batteries can cause injury.

WARNING: Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. After changing batteries, always completely close and secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the battery, and keep it away from children. If you think battery might have been swallowed or placed inside any part of the body, seek immediate medical attention.

SETTING UP YOUR UNIT

Parts:

1. Air Output Vents
2. Control Panel
3. Front Display
4. Air Purifier Base
5. Air Intake Vents
6. Filter
7. Filter Door

TIPS FOR SETTING UP YOUR UNIT

• Make sure the front panel of the unit faces away from the closest wall.
• Do not move the unit while it is running. Turn off the power and unplug the unit before moving it.
•  Make sure the vents are not blocked.
• Do not place anything on the air purifier.
•  Do not place the air purifier near heaters or radiators.
• Keep the unit out of direct sunlight and away from water or other liquid.
• Keep all nearby doors and windows closed when operating the air purifier.
• Avoid using in very humid environments.

1. First, carefully flip the air purifier upside down and place it on a level surface. Twist the filter door to unlock the filter.

2. Take the filter out of its packaging, then insert it back into the unit. DO NOT run the air purifier unless the filter is removed from its packaging and properly reinstalled.

3. With the filter reinstalled, twist the filter door until it clicks into place.

4. Set up the unit on a level surface, at least 3 inches (8 cm) away from walls and objects.

5. Plug the unit into an electrical outlet and press the power button on the top control panel.

6. When the unit is powered on, it will begin to analyze the air quality indicated by the rotating lights. After a few seconds the unit will display the current air quality.

CONTROL PANEL

A control panel on the top of the unit and a display screen on the front of the unit.

TOP CONTROL PANEL

TOP CONTROL PANEL BUTTONS

• On/Off: Press to turn the power on or off.
• Auto Mode: Press to turn on Auto Mode. In this setting the fan speed automatically adjusts based on real time air quality readings. As the air quality improves, the fan speed will decrease. If air quality worsens, the fan speed will increase. Leave your unit in Auto Mode for optimal filter life and performance.
• Fan Speed: Adjusts the speed of the fan. Select one of 4 settings: 1 Low, 2 Medium, 3 High, 4 Maximum. Note: If fan speed is manually changed, auto mode will be deactivated. For tips on optimal fan setting, see Optimizing Fan Speed section.
• Air Info: Press to switch between air quality display options. See the Air Info Settings section for more information.
• Brightness: Adjusts the brightness of both the front display screen and the top control panel. Switch between 3 options: full brightness, partially dim, fully dim.
• Shut-Off Timer: Set the number of hours for the air purifier to run before it automatically shuts off. Timer can be set between 1-12 hours.
• Filter Life: Press to show the remaining filter life. Once the filter has 0% remaining, the FILTER LIFE button will flash to indicate the filter needs to be changed. See Installing and Removing the Filter section for more information
• Child Lock: Hold for two seconds to lock the top control panel buttons. To unlock, hold for two seconds again.

Tips and Tricks:

• Optimize Performance in Eco Mode: After 100% clean air status is achieved for 70 minutes in Auto Mode, your air purifier will enter Eco Mode. Your unit’s filter life will be optimized!
• Control Your Air Purifiers Beeping: Hold the Air info and Child Lock buttons at the same time for tow seconds
  

AIR INFO SETTINGS

The built-in sensor detects your air quality to give you real-time information. Use the AIR INFO button CD to switch between air quality display options.

UNDERSTANDING YOUR AIR QUALITY

The rings on the front and top displays will change color as your air quality changes, allowing you to easily monitor your air quality even when you are far from the unit.

Note: The air quality sensor uses a cumulative particle count across all particle sizes to determine percentage of clean air.

OPTIMIZING FAN SPEED

Your air purifier is equipped with 4 fan speed settings. Adjust fan speed to optimize your cleaning performance.

TROUBLESHOOTING AND FREQUENTLY ASKED QUESTIONS

INSTALLING AND REMOVING THE FILTER

NOTE: Always remove all protective packaging from the filter before installing.

When the filter timer has 0% remaining, the FILTER LIFE button on the top control panel will blink, indicating that it’s time to install a new filter.

1. Turn off and unplug the unit before removing or installing filters.
2. Carefully flip the air purifier upside down. Remove the bottom filter by twisting to the unlocked position.
3. To remove the old filter, pull it out by the removal tabs. Discard old filter in trash.
4. Remove all packaging and wrapping from the new filter.
5. Insert the new filter, then replace the filter door. Twist the filter door until it clicks into place.
6. Carefully, return the air purifier to the upright position. Plug the unit back in and turn on power. Calibration will begin.
7. After installing a new filter, press and hold the Filter Life button on the top control panel for 3 seconds to reset the filter life percentage. The unit will beep when the filter life is reset to 100% .

Disposing of used filters
Filters can’t be cleaned or recycled. After removing a used filter, wrap it in an airtight plastic bag for disposal. As an extra precaution, wear gloves when handling a dirty filter.

MAINTAINING YOUR AIR PURIFIER

NOTE: Always unplug the unit before doing any cleaning or maintenance.
Exterior Cleaning:
For best results, clean the exterior of the unit every two months or as needed. Use a microfiber cloth to remove dust. To sanitize, wipe down the exterior with a microfiber cloth dampened with warm, soapy water. Avoid excess water and abrasive chemical cleaners to prevent damage.

Interior Cleaning:
For best results, clean the interior of the unit every two months or as needed. Remove the filter door, take out the filter, and use a vacuum cleaner or a microfiber cloth to remove dust and debris from the interior of the unit. DO NOT use abrasive chemical cleaners on the inside of the unit.

AVAILABLE ACCESSORIES

ORDER ADDITIONAL ACCESSORIES AND REPLACEMENT FILTERS

Additional accessories and replacement filters are available on

SHARK® NANOSEAL™ BASE FILTER WITH TRUE HEPA
Captures 99.98% of large, small, & micro-sized particles from the air and is equipped with carbon for heightened protection against household odors and VOCs.

SHARK® NANOSEAL™ BASE FILTER WITH TRUE HEPA+ MICROBAN
Captures 99.98% of large, small, & micro-sized particles from the air and is equipped with carbon for heightened protection against household odors and VOCs.

TREATED WITH MICROBAN:
Additional antimicrobial protection with Microban treatment. Microban reduces the bacterial growth on the HEPA surface.

REMOTE CONTROL BUTTONS

1. On/Off: Turns the unit on/off.
2. Air Info: Switch between air quality display options.
3. Auto: Enables Auto Mode.
4. Brightness: Adjusts brightness.
5. Fan Speed: Adjusts fan speed.
6.  Shut-Off Timer: Sets timer.

Remote Control
Use the remote control to operate your air purifier from a distance.

TWO (2) YEAR LIMITED WARRANTY

The Two (2) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable. SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:

What is covered by this warranty?

1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to two (2) years from the original purchase date.
2.  In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as filters and batteries, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.

2. Any unit that has been tampered with or used for commercial purposes.

3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance (e.g., not replacing the filters), or damage due to mishandling in transit.

4. Consequential and incidental damages.

5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.

6. Products purchased, used, or operated outside North America.

   • How to get service
     If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/ support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-855-523-4061 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call. SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

   • How to initiate a warranty claim
     You must call 1-855-523-4061 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product on line at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.

   • How state law applies
     This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

IMPORTANT INFORMATION

REGISTER YOUR PURCHASE

• registeryourshark.com
• Scan QR code using mobile device

TECHNICAL SPECIFICATIONS

• Voltage: 120V~ 60Hz
• Watts: 36W

Benefits of registering your product and creating an account:

• Get easier, faster product support and access to warranty information
• Access troubleshooting and product care instructions
• Be among the first to know about exclusive product promotions
  TIP: You can find the model and serial numbers on the QR code label on the bottom of the unit.

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark® Air Purifier.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398 sharkclean.com

Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. Patent information, visit sharkninja.com/patents
© 2022 SharkNinja Operating LLC. SHARK is a registered trademark of SharkNinja Operating LLC. CLEAN SENSE IQ and NANOSEAL are trademarks of SharkNinja Operating LLC.

BATTERY REMOVAL AND DISPOSAL

This product’s remote control uses a lithium button battery. When the battery no longer has a charge, it should be removed from the remote and recycled. DO NOT incinerate or compost the battery.

When your lithium battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop off the spent battery.

FCC WARNINGS

Note: This unit has been tested and found to comply with FCC limits for Class B digital devices. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this unit may not cause harmful interference, and this unit must accept any interference received, including interference that may cause undesired operation. To see if this unit interferes with radio or television reception, try turning it off and on. To correct any interference:

• Reorient or relocate the receiving antenna .
• Increase the distance between the unit and the receiver.
• Connect the unit to a different outlet than the receiver.
• Consult the dealer or an experienced technician for help .

Caution: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate it.

References

• Find Sharkclean Parts & Accessories | Sharkclean

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>