DELUX M618XSDW Vertical Mouse User Manual
- June 5, 2024
- DELUX
Table of Contents
DELUX M618XSDW Vertical Mouse
FUNCTIONS
-
OLED Screen
-
Forward
-
Backward
-
Left button
-
Right button
-
Charging indicator
-
Scroll wheel
-
DPI
-
9Palm rest
-
Thumb scroll wheel
-
ON/OFF.
-
Mode indicator
-
Mode switching button
-
Receiver storage slot
-
Receiver
Wired/2.4G wireless switching
Tap the mode switching button can switch to the connected mode, the corresponding mode indicator flashes (the light goes off when wired connected) when you are in one status, and the OLED screen will show you the connected mode.
Connected Mode
Wired mode:
Connecting the mouse to the computer via type C, tap the switching button until the light goes off PS. Wired mode is available to use when you turn ON or OFF the mouse.
2.4G Wireless mode: Turn on the mouse after inserting the receiver into the device, then tap the switching button to 2.4G wireless mode. The mouse can be used when the corresponding indicator light goes off. (If you need to reset the mode: press the switching button for about 3s when you are in the 2.4G mode, the indicator light flashes quickly and then goes off means you reset the mode successfully.)
Light mode switching
5 types of light can be switched when you press the right button and backward button at the same time. (the driver can adjust the backlight too)
Automatic sensing Light
The default is to turn on the light sensor. The backlight goes off when your palm is close to the mouse. Press the right and left buttons at the same time for about 3s, the light sensation turns off when flashed 2 times white light. Long press the right and left buttons to reopen the light sensation.
Hotkey to close the side button’s function
Press forward button + backward button for 3s can close these two buttons’ functions.
Long press this two-button can reopen the function.
DPI switching
Tap the DPI button to switch the DPI.
800 (red light) – 1200 (green light)- 1600 (blue light)
2400 (purple light) – 4000 (yellow light), Switching DPI Successfully
when the corresponding light flashed twice. Default DP: 1200 (600-4000).
Report rate
Wired/2.4G mode: 125Hz-250Hz- 500Hz-1o00Hz,
Default 500Hz, can be changed by the driver.
Thumb scroll
wheel Rolling up Moving to the left
Rolling down > Moving to the right
(can be used in office software, browser, etc)
Driver installation
- Installation
Download from DELUX website: www.deluxworld.com.
- Setting
Opening the driver (when using the mouse) to set the functions.
- Multi-group file configuration
Click”+” on the top-left of the interface to create a new configuration file.
Click The current configuration file can be deleted. Click The current
configuration file can be copied. Click The current configuration file can be
renamed.
- Light setting
Click “Light setting” to set the light.
- Button setting
Click “Button settings” to set the buttons. Click after all settings are
done.
- Macro management
Click “Macro management” to set the Macro. Click “+” to create a new Macro,
then click “REC” to record. Enter the key that you need on the keyboard when
recording. Click “STOP” to stop the Macro recording. Import Macro instruction:
select the button you need to set, then click “Macro function” to choose the
Macro name, then click “save” to complete the setting.
- DPI setting
Click “Other settings” to set the DPI.
- Default settings
Click to reset, then click “OK” to complete the setting.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>