makita DTD155 Cordless Impact Driver Instruction Manual
- June 5, 2024
- Makita
Table of Contents
Cordless Impact Driver
INSTRUCTION MANUAL
DTD155
|
---|---
Original instructions
SPECIFICATIONS
Model: | DTD155 |
---|---|
Fastening capacities | Machine screw |
Standard bolt | 5 mm – 14 mm |
High tensile bolt | 5 mm – 12 mm |
No-load speed | Hard impact mode |
Soft impact mode | 0 – 1,300 min-¹ |
Impacts per minute | Hard impact mode |
Soft impact mode | 0 – 1,600 min-¹ |
Rated voltage | D.C. 18 V |
Overall length | 135 mm |
Net weight | 1.2 – 1.5 kg |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge| BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
---|---
Charger| DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
- Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire.
Intended use
The tool is intended for screw driving in wood, metal, and plastic.
Noise
The typical A-weighted noise level determined according to
EN62841:
Sound pressure level (LpA): 94 dB(A)
Sound power level (LWA): 105 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared noise emission value(s) may also be used in a
preliminary assessment of exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual use of the power tool can
differ from the declared value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that
is based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) is determined according to
EN62841:
Work mode: impact tightening of fasteners of the maximum capacity of the tool
Vibration emission (ah) : 14.0 m/s²
Uncertainty (K) : 2.0 m/s²
NOTE: The declared vibration total value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared vibration total value(s) may also be used in a
preliminary assessment of exposure.
WARNING: The vibration emission during actual use of the power tool can
differ from the declared value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that
is based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included in Annex A in this instruction
manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Cordless impact driver safety warnings
- Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
- Hold the tool firmly.
- Wear ear protectors.
- Do not touch the bit or the workpiece immediately after operation. They may be extremely hot and could burn your skin.
- Keep hands away from rotating parts.
- Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
- Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with the product (gained from
repeated use) replace strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated in this instruction manual
may cause serious personal injury.
Important safety instructions for battery cartridge
-
Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.
-
Do not disassemble the battery cartridge.
-
If the operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
-
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
-
Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.
(3) Do not expose the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns, and even a breakdown. -
Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
-
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
-
Be careful not to drop or strike the battery.
-
Do not use a damaged battery.
-
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirements on packaging and labeling must be observed. For the preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
-
Follow your local regulations relating to the disposal of batteries.
-
Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that have been altered, may
result in the battery bursting causing fires, personal injury, and damage. It
will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge at room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking the function of the tool.
Installing or removing the battery cartridge
CAUTION: Always switch off the tool before installing or removing of the
battery cartridge.
CAUTION: Hold the tool and the battery cartridge firmly when installing
or removing the battery cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands and result in damage to
the tool and battery cartridge and a personal injury.
► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge To remove the
battery cartridge, slide it from the tool while sliding the button on the
front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge
with the groove in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
► Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indicate the remaining
battery capacity. The indicator lamps light up for a few seconds.
Indicator lamps|
Remaining capacity
---|---
Lighted| Off| Blinking
|
75% to 100%
|
50% to 75%
|
25% to 50%
|
0% to 25%
|
Charge the battery.
|
The battery may have malfunctioned.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
Tool/battery protection system
The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions:
Overload protection
When the battery is operated in a manner that causes it to draw an
abnormally high current, the tool automatically stops without any indication.
In this situation, turn the tool off and stop the application that caused the
tool to become overloaded. Then turn the tool on to restart.
Overheat protection
When the tool/battery is overheated, the tool stops automatically. In this
situation, let the tool/battery cool before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops automatically. In this
case, remove the battery from the tool and charge the battery.
NOTE: Overheat protection (for battery) will work only with batteries with
star marking.
► Fig.3: 1. Star marking
Switch action
► Fig.4: 1. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
NOTE: The tool automatically stops if you keep pulling the switch trigger for about 6 minutes.
Lighting up the front lamp
CAUTION: Do not look in the light or see the source of light directly.
► Fig.5: 1. Lamp
► Fig.6: 1. Button
Pull the switch trigger to turn on the lamp. To turn it off, release it. The
lamp goes out approximately 10 seconds after releasing the switch trigger.
To keep the lamp off, turn off the lamp status. First, pull and release the
switch trigger. And then press the button for one second within 10 seconds.
To turn on the lamp status again, press the button again similarly.
NOTE: To confirm the lamp status, pull the trigger.
When the lamp lights up by pulling the switch trigger, the lamp status is ON.
When the lamp does not come on, the lamp status is OFF.
NOTE: When the tool is overheated, the light flashes for one minute, and
then the LED display goes off. In this case, cool down the tool before
operating again.
NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be
careful not to scratch the lens of the lamp, or it may lower the illumination.
Reversing switch action
► Fig.7: 1. Reversing switch lever
CAUTION: Always check the direction of rotation before operation.
CAUTION: Use the reversing switch only after the tool comes to a complete
stop. Changing the direction of rotation before the tool stops may damage the
tool.
CAUTION: When not operating the tool, always set the reversing switch
lever to the neutral position.
This tool has a reversing switch to change the direction of rotation. Depress
the reversing switch lever from the A-side for clockwise rotation or from the
B-side for counterclockwise rotation.
When the reversing switch lever is in the neutral position, the switch trigger
cannot be pulled.
Changing the impact force
► Fig.8: 1. Hard 2. Soft 3. A mode 4. Changed in three steps 5. Button
You can change the impact force in three steps: hard, soft, and A mode.
This allows a tightening suitable to the work.
Every time the button is pressed, the number of blows changes in three steps.
“A mode (assist mode)” is an easy-to-use mode for driving screws with good
control.
In this mode, the tool drives a screw with low-speed rotation at first. After
the tool starts to impact, the rotation speed increases and reaches the
maximum speed.
You can change the impact force within approximately one minute after
releasing the switch trigger.
Impact force grade displayed
on panel| Maximum blows| Purpose| Example of application
---|---|---|---
Hard| 3,900 min-1 (/min)| Tightening when force and speed are desired.|
Tightening wood screws, tightening bolts.
Soft| 1,600 min-1 /min)| lightening with less force to avoid screw thread
breakage.| Tightening sash screws, lightening small screws such as M6.
A mode| 3,900 min-1 (/min)| Tightening screws with better control.|
Tightening long screws.
NOTE: A mode is available only when the tool rotates clockwise. When
rotating counterclockwise in A mode, the impact force and speed are the same
as hard mode.
NOTE : When all lamps on the switch panel go out, the tool is turned off
to save the battery power. The impact force grade can be checked by pulling
the switch trigger to the extent that the tool does not operate.
NOTE: While pulling the switch trigger, the impact force grade cannot be
changed.
ASSEMBLY
CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
Installing or removing driver bit/ socket bit
Optional accessory
► Fig.9
Use only the driver bit/socket bit that has the inserting portion shown in the
figure. Do not use any other driver bit/socket bit.
For tool with shallow driver bit hole
A=12mm
B=9mm| Use only these types of driver bits. Follow procedure 1. (Note) Bit-
piece is not necessary.
---|---
For a tool with a deep driver bit hole
A=17mm
B=14mm| To install these types of driver bits, follow procedure 1.
---|---
A=12mm
B=9mm| To install these types of driver bits, follow procedure 2.
(Note) Bit-piece is necessary for installing the bit.
-
To install the driver bit, pull the sleeve in the direction of the arrow and insert the driver bit into the sleeve as far as it will go. Then release the sleeve to secure the driver bit.
► Fig.10: 1. Driver bit 2. Sleeve -
To install the driver bit, pull the sleeve in the direction of the arrow and insert the bit-piece and driver bit into the sleeve as far as it will go. The bit piece should be inserted into the sleeve with its pointed end facing in. Then release the sleeve to secure the driver bit.
► Fig.11: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction of the arrow and
pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough into the sleeve, the
sleeve will not return to its original position and the driver bit will not be
secured. In this case, try re-inserting the bit according to the instructions
above.
NOTE: After inserting the driver bit, make sure that it is firmly
secured. If it comes out, do not use it.
Installing hook
CAUTION: When installing the hook, always secure it with the screw
firmly. If not, the hook may come off from the tool and result in personal
injury.
► Fig.12: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install the hook, insert
it into a groove in the tool housing on either side and then secure it with a
screw. To remove, loosen the screw and then take it out.
OPERATION
► Fig.13
The proper fastening torque may differ depending upon the kind or size of the
screw/bolt, the material of the workpiece to be fastened, etc. The relation
between fastening torque and fastening time is shown in the figures.
Standard bolt
- Fastening time (second)
- Fastening torque
- Proper fastening torque corresponding to each bolt diameter
High tensile bolt
- Fastening time (second)
- Fastening torque
- Proper fastening torque corresponding to each bolt diameter
Hold the tool firmly and place the point of the driver bit in the screw head.
Apply forward pressure to the tool to the extent that the bit will not slip
off the screw and turn
the tool on to start operation.
NOTICE: If you use a spare battery to continue the operation, rest the
tool for at least 15 min.
NOTE : Use the proper bit for the head of the screw/ bolt that you wish
to use.
NOTE: When fastening an M8 or smaller screw, choose a proper impact force
and carefully adjust the pressure on the switch trigger so that the screw is
not damaged.
NOTE: Hold the tool pointed straight at the screw.
NOTE: If the impact force is too strong or you tighten the screw for a
time longer than shown in the figures, the screw or the point of the driver
bit may be overstressed, stripped, damaged, etc. Before starting your job,
always perform a test operation to determine the proper fastening time for
your screw.
The fastening torque is affected by a wide variety of factors including the following. After fastening, always check the torque with a torque wrench.
-
When the battery cartridge is discharged almost completely, the voltage will drop and the fastening torque will be reduced.
-
Driver bit or socket bit
Failure to use the correct size driver bit or socket bit will cause a reduction in the fastening torque. -
Bolt
• Even though the torque coefficient and the class of bolt are the same, the proper fastening torque will differ according to the diameter of the bolt.
• Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque coefficient, the class of bolt, and the bolt length. -
The manner of holding the tool or the material of the driving position to be fastened will affect the torque.
-
Operating the tool at a low speed will cause a reduction in the fastening torque.
MAINTENANCE
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before attempting to perform inspection or maintenance.
NOTICE: Never use gasoline, benzene, thinner, alcohol, or the like.
Discoloration, deformation, or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, and any other maintenance
or adjustment should be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with
your Makita tool specified in this manual. The use of any other accessories or
attachments might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask
your local Makita Service Center.
- Driver bits
- Socket bits
- Bit piece
- Hook
- Tool hanger
- Plastic carrying case
- Makita genuine battery and charger
- Battery protector
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Europe N.V.
Makita Corporation
Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan
885520C990
EN, FR, DE, IT, NL, ES, PT, DA, EL, TR
20190227
www.makita.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>