Blue Pluser BROPOR-180 Reverse Osmosis 180G Water Purifier Owner’s Manual

Blue Pluser BROPOR-180 Reverse Osmosis 180G Water Purifier

Thank you for choosing our Ro water purifier system please read this manual carefully and follow the instruction during installation

ATTENTION

Read these instructions carefully before installing or using this appliance.

Matters needing attention:

1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. That the appliance is only to be used with the power supply unit provided with the appliance .
4. The product must be disconnected power supply during installation or maintenance.
5. Fifth supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

SPECIAL NOTE: In the beginning, because of new filter cartridges activation, TDS value of outlet water will be a little high and there might be a light weird taste. In first time use, please flush system 10-15 times and pour away these water. Every machine was tested before package, thus there might be a little droplets with machine.

PARAMETER

NO.

| ****

ITEM

| PARAMETER
---|---|---
75G| 180G
1| NetWelpt| 8.4 kg| 8.9 kg
2| Gross Weight| 10.6 kg| 11.3 kg
3| Pure Water Flow| 0.21/min| 0.471/min
4| Total Pure Water

Volume

| 285 L| 2000L
5| Rated Power| 36W| 48W
6| SIZE| 276362392 mm
7| Input Voltage| DC24V
8| Inlet water

temperature

| 5-38’C
9| Inlet waterpressure| 0-0.2MPa
10| ConDpratlon| Four Stages With Pump
1 1| l!lectr C”Slioek

Resistance

| m
12| rTliletwater

quality

| Tap water
13| Pure Water

Kettle Volume

| 1.7L
14| Heat Pot Kettle Volume| l.SL

15

|

SWltchlng

Adapter

| Lnput:

100V-240Y; 5011HOlb

or S0Hz/601b; 1.SA;

Claull.

| Lnput:

100V-240V; 501h-601b

or 50Ha/60Hz; 1.SA;

au.,.

DC-output:

24.0V; 1.SA; 36W.

|

DC-output:

24.0V; 2.0A; 48W.

• Pure water flow is testing under laboatory condition
• The Power Supply was intended for charge and/or supply of household appliances. For charging purpose, unit should be used together with charging base or the similar in which necessary protection of abnormal charging was provided.

STEP

1ST USAGE

1. For the lsttime usage.please flush the inlet water tank and pure water kettle;
2. Please fill water to the Max line of the inlet water tank;
3. The water purifier system needs to be placed horizontally, and makesure that the inlet water tank and pure water kettle are all placed well;
4. 2-3 inlet tanks water will be filled into the new filters for the 1st usage,and it may no water out;
5. ln order to the safety of drinking water,please pour out the 4- 5th tanks of outlet water.
   Notice: For the 1st time usage or flush,it may appear the black water, it is normal phenomenon by the activated carbon for the new filter.

It is recommended to clean the filter when using it every day, the first tank outlet of water is returned to inlet tank and filtered again or pour out. as some water stay in the filter since last usage.

Intelligent water purification

1. Take out raw water tank, and fill it with tap water, and press the blue round rect button to start making pure water;

2. To press the flow button can control the level of water you want, four color blocks indicate on the LCD screen, one blocks represents 1/4 kettle water,at first is full kettle, pressone time will turn on one block and producing 1/4 kettle water, press the button again will turn on two blocks then produce 2/4 kettle water, the rest can be done in the same manner, and it can be switched in order;

3. According the different water quality in different area, it takes about 3-5 minutes to finish one kettle water, (it takes
   7 minutes for 75GPD to fill in on kettle water);

4. During the pure water process, just press again the blue round rect button to stop produce water;

5. When the purifiers are stand by 5 minutes, the LCD screen will turn off, and enter to power safe modes, the LCD screen will be auto bright and enter stand by mode after press again the blue round rect button or put up the inlet water tank.

If the purifiers does not work, please check the conditions as below:

1. The plug does not be inserted, and two switches do not turn on;
2. purifiers; The raw warer tank does not be placed well with the
3. The purifiers; pure water water level in kettle the raw does not water be tank placed is lower well with than the inlet water line.

SCREEN

PURE

1. The water volume and water-making button lights flash every second. After 18 seconds, the water volume button lights stop flashing , the water-making button lights flashes every second, and the water volume and water-making button lights are always on when the water-making is finished
2. By pressing the banana shape button lightly, you can cyclically choose water producing volume of 0.5L . 1 Land l.SL(full). (The default value at power-on is 1.7L).

Flush
The water volume and water-making button lights flash every second

TDSValue
Since the wastewater will continue to return to the raw water tank, the water inlet value will gradually increase. The outlet TDS value will initially change slightly and finally stabilize at a constant value,and that is the true and final TDS value of the water after filtration.

Filter monitoring display:

• Digital: filter stages
• Block light: lifetime of the filters

Press the water volume button to cyclically select water producing volume of O.SL, ll and l.SL and there is also a default volume of l.7L.

FILTER

RO POT with Reverse Osmosis as the core technology of the 4 stages filters system.

RO reverse osmosis:
Reverse osmosis is known as reverse osmosis, a membrane separation operation that it separates the solvent from the solution with the pressure difference as the driving force. When pressure exceeds its osmotic pressure, the solvent will reverse osmosis in the direction of natural penetration. Thus, the permeable solvent is obtained through the low pressure side of the membrane. A concentrated solution, or concentrated solution, is obtained at the high- pressure side.
Reverse osmosis membrane can intercept greater than 0.00001-micron material, is one of the most delicate membrane separation products, it can effectively intercept all dissolved salts and organic molecular weight greater than 100, while allowing water molecules to pass at the same time.

RO reverse osmosis graphical representation:

Filtering step:

1. PP sediment filter, which can remove floater such as sand, iron rust, copper rust and phosphor;
2. CTO carbon block filter, which can remove chlorine, organic, color, odor and floating particles;
3. RO membrane, which can remove bacteria, virus, chemical material, and heavy material;
4. CCF which can improve the taste. (180GPD with RO membrane at 4th stage)

Life time of filters:

Note:
When any frame of the four stages is flashing or the four color blocks are all off,Users need to change the filters, one block means 1/4 lifetime.

Replacing filters
RO POT uses screw-in type easy changeable design, users can change the filter by themselves.

1. Turn off the power, and remove the water in raw watertank, then open the filter cover;
2. Hold the filter at 45° position;
3. Screw it left-handed way to remove the old filter;
4. There is a trapezium on the filter, adjust it to the triangle on the filter cap and screw it to the cap right-handed tightly;
5. Turn on the power, fill water in the raw water tank, and press the operation button to reflash the new filters.

QUESTION

• Q: Why the purifiers does not work?
  A: Please check the purifiers if it is out of power or save-power condition, we suggest to reset the power or press two swith.

• Q: why the purifierss does not produce water?
  A. Please check if the raw water tank has changed the water, the water level needs to be higher than the inlet water line.

• Q:l already place the water tank, and water inside, why the water tank menu still blink?
  A: Please check if the tank has been placed well, we suggest to adjust the water tank position.

• Q: Why the leakage of water?
  A: Please check if the filters have been settled tightly, or we  suggest to re-installed the filters.

• Q: Why the new filters Jasper very soon after change the filters?
  A: The lifetime of filters are related to the inlet water quality and purifiers use times, the poor water quality and operating frequency leads the short lifetime.

• Q: Why the pure water looks dirty?
  A: If the pure water appears black water with new filters, it is casued by CTO of the new filters, it it normal phenomenon, please change the water and rellush 2-5 times until the TDS value around 40.

• Q: Why the TDS value is still high after filtration?
  A:The TDS value relates to the inlet water quality, lifetime of the filters. Poorer water quality, longer usage of filters, the TDS value higher.In order to make sure drinking water health, we need to change the filters promptly.If the TDS is still high after change the filters, please call the service number: 400-800-3201, the professional people will help you to fix the problem.

• Q: Why droplets appears on the purifiers after open the package?
  A:This is the reason that evey purifier tested before package, the droplets in the pipe can not be removed, it is normal phenomenon.  
  

LIST

• ROPOT*l
• Pure water kettle *1
• Users’ manual*l
• Certificate of qualification 1 Adapterl

1. Accoding to the improvement for the product, the words or pictures on the users’ manual may little difference from the kind,Please pay attention to our website.
2. All the contents of this information are carefully checked, if any printing mistake or confusion, our company preserve the explanation right. 

GUARANTEE

The warranty period of this product (except for the filters) is one year from the day of purchase. Customer can contact the Customer Support Center to make an appointment for maintenance if any abnormality or failure occurs.
After the warranty period, customers will need to pay reasonable charges for maintenances.

The following conditions are excluded from the warranty:

1. Out of the period of “three guarantees” (for repair, replacement or compensation of faulty products) validity;
2. Absence of product package, accessories, gift, user manual or invoice;
3. Damages caused by force majeure;
4. Repair, misuse, collision, neglect, liquid inlet, accident, refit or dismantling of the product, or use of components that are not original from the product, without the authorization by Kflow in each instance. Tearing up or altering labels, series number or anti-fake marks or committing other similar activities;
5. The product model No. in “three guarantees” has been altered or is different from the model No. of the product which requires repair;
6. Damages caused by not following the manual instructions regarding operating environment (such as temperature, humidity, ventilation conditions);
7. Failure or damage caused by the abnormal operating conditions;
8. The product will be out of warranty if used for commercial purpose.

SERVICE

RO SERVICE CARD (Users Retention)

Name|  | TEL|
---|---|---|---
Model|  | ADD|
Serial No|  | E-mail|
Maintain & upkeep maintenance program record

Date

| 1st stage| 2nd

stage

| 3rd stage| 4th stage|

Others

|

Remarks

| Service

personnel

| | | | | |
| | | | | | |
| | | | | | |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>