dyson cordless vacuum cleaner User Manual

cordless vacuum cleaner
User Manual

The Dyson upright vacuum cleaner front view with the cleaner head, ball, bin and handle attached.

In the box

Some tools and accessories may not be included.
You can buy additional tools and accessories at www.dyson.com.

This tool has a combination of brush head and crevice tool
together in one unit. The brush head slides down the crevice tool when needed.| | Combination tool Two tools in one – brush and nozzle, for versatile cleaning around your home.
---|---|---
A wide mouth tool with a lint edge.| | Stair tool
For vacuuming narrow or difficult-to-reach
carpeted areas, such as stairs and corners.
A small cleaner head with a body housing the motor and an electrical connector to attach to the wand or directly to
the machine.| | Tangle-free turbine tool
Counter-rotating brush heads remove hair from carpets
and upholstery. No tangles.
Soft bristles are on the underside of this tool.| | Soft dusting brush Enclosed in a skirt of soft nylon bristles for gentle, vacuum-assisted dusting of delicate objects and surfaces.
A wide, triangular shaped nozzle.| | Fabric and mattress tool Removes dust, dirt and allergens
from mattresses and upholstery.
A long rectangular tool with a jointed connection and
soft bristles on the underside.| | Articulating hard floor tool Swivelling brush head with an ultra-slim profile to reach difficult spaces. With soft nylon
bristles to remove dust and allergens.
A springloaded head with metal bristles on the underside.| | Pet groom tool Captures loose hair and dander as you
brush your pet. Flexible bristles self-clean in an instant.
clik

Getting started

Assembling your machine

Fit the cleaner head
Lay your machine on its back.
Slide your Motorbar™ cleaner head into position on the front of the ball.
Push upwards until the red button on the underside of your machine clicks securely in place.
Stand your machine upright. Fit the wand
Slide the handle onto your machine until it clicks into position.
Position the wand into the end of the hose. Press the wand release button on the end of the hose and slide the wand all the way down.
Position the wand and hose in the handle recess on your machine. Slide the wand down into the handle until it clicks into position.
Close the wand end cap. Fit the tool holder
Slide the tool holder into position on the side of your machine.
Fit your combination tool onto the holder. Wrap the cable around the top and bottom cable hooks and secure it with the cable clip.

Caring for your floors

Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage.
Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions.
The brush bar on your machine can damage certain flooring. Some rug materials may fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming without the motorized floor tool and consulting with your flooring manufacturer.

Using your Motorbar™ cleaner head

Your cleaner head has a motor-driven brush bar with suction control.
Check the manufacturer’s recommended cleaning instructions for your flooring type.
Slide the suction control to suit your floor type. Select the right cleaning mode for the right task.

Position the slider to the left for use on deep- to medium-pile carpets, delicate flooring and rugs.|
---|---
Position the slider in the center for low-pile carpets and large debris.|
Position the slider to the right for hard floors and ground-in dirt.|
If your machine is hard to push, use the mode on the left.|

Using your tools

Attach to the wand
Open the cap on the handle and slide the wand upwards until both the wand and hose are released from the machine.
Push the tool into the end of the wand.
Remove from the wand
Remove the tool and slide the wand back into the hose. Position the wand and hose in the recess on the handle of your machine.

Attach to the hose
Open the cap on the handle and slide the wand upwards until both the wand and hose are released from the machine.
Press the button on the end of the hose to release the wand.
Fit the tool into the end of the hose.
Remove from the hose
Remove the tool from the end of the hose.
Push the wand into the end of the hose until it clicks into position.
Slide the wand down into the hose.
Close the wand end cap.

Emptying your bin

Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine, when the dirt is above the MAX line, may affect the performance and require more frequent filter washing. Remove your bin
Turn off and unplug your machine.
Press the button on the bin handle to detach the bin from your machine.
Release the dirt
Hold your bin, with the bin base pointing down, over your trash can.
Firmly push the button on the bin handle, until the bin base opens.
Minimize dust contact
Cover your bin tightly in a dustproof bag while you empty. Remove
your bin carefully, seal the bag tightly and dispose of it.
Replace your bin
Push the bin base up until it closes, clicking into place.
Position the bottom of your bin on your vacuum cleaner and then push the top into your machine until it clicks securely into place.

Storing your machine

Carry your machine using the bin handle.
Push your handle into the upright position.
Push your handle firmly forward and listen for two clicks to lock in an upright position.
The stabilizer wheels will drop into position when the handle is locked in the upright position.

Clearing blockages

If any part of your machine becomes blocked, it may automatically cut out and the power will stop.
Unplug and leave your machine to cool before checking for blockages.
Remove cleaner head
Lay your machine on its back.
Push down the red button on the bottom of the ball and then slide your cleaner head down and off your machine.

Check the wand
Open the cap on the handle and slide the wand upwards until both the wand and hose are released from the machine.
Press the button on the end of the hose to release the wand.
Look through the wand to check for blockages.

Check the hose
Open the cap on the handle and slide the wand upwards until both the wand and hose released from the machine.
Press the button on the end of the hose and remove the wand.
Press the button on the bin handle and remove the bin. Press the tab on the base of the hose to remove it from your machine.
Check for blockages in the hose, and be careful of any sharp objects.

Check airways for blockages
Recline your machine and remove the outer cover of the ball.
Press the button on the handle of the bin and lift it away from your machine. Locate the clear inspection panel at the bottom of the bin recess on your machine and lift it to one side. Remove any debris.
Remove the cleaner head and look for blockages in the airway.
Check all the airways, removing any debris before reassembling your machine.

Clearing obstructions from yourMotorbar™ cleaner head

Your Motorbar™ cleaner head doesn’t have a washable brush bar.
To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Unplug and leave your machine to cool before checking for blockages.
Remove cleaner head
Lie your machine on its back.
Push down the red button on the bottom of the ball and then slide your cleaner head down and off your machine.

Remove your brush bar
Press the button on the back of the Motorbar™ cleaner head and push upwards 90° to release the end cap.
Pull the brush bar out of the cleaner head.
Remove any hair, thread, or debris from around the brush bar.
Be careful of any sharp objects when clearing blockages.
Replace your brush bar
Push the brush bar firmly back into the cleaner head.
Make sure the brush bar is pushed fully into the cleaner head. Rotate the end cap until it clicks back into the locked position.

Reassemble the cleaner head
Slide your Motorbar™ cleaner head into position on the front of the ball. Push upwards until the red button on the underside of your machine clicks securely in place.

Washing your filters
Wash your filters at least once a month to maintain optimum suction power.
For more information and support videos for your machine go online: www.dyson.com/support

Washing filter A

Remove your filter
Press the button on the bin handle to detach the bin from your machine.

Wash your filter
Push up the catch on the front of the bin handle and lift out the filter.
Only wash the filter with cold water. Hold the open end of the filter under a running tap, until the water runs clear.
Turn the filter upside down and tap to remove excess water.
Run water over the outside of the filter until the water runs clear.
Squeeze and twist with both hands to make sure the excess water is removed.
Dry your filter
Squeeze the excess water out of your filter.
Leave your filter to dry for at least 24 hours in a well-ventilated, warm place.
Don’t dry your filter in a tumble dryer, microwave, or near a naked flame.
Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

Reassemble your filter
Drop your filter back into your machine. Close the handle and make sure it clips into place.
Place the base of your bin onto your machine and then push the top into position until it clicks.

Washing filter B

Remove your filter
Lay your machine on its side with the filter cover facing upwards.
Turn the lock in the center of the ball until the filter cover is released. Lift off the filter cover.
Twist the filter counter-clockwise until it is released and lift it off your machine.
Wash your filter
Wash the filter in a rotating motion.
Repeat until the water runs clear.
Tap the filter to remove excess water.

Dry your filter
Leave your filter to dry for at least 24 hours in a well-ventilated, warm place.
Don’t dry your filter in a tumble dryer, microwave or near a naked flame.
Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.
** Reassemble your filter**
Place the filter back into position in the ball.
Twist the filter clockwise until it clicks into position.
Refit the filter cover and turn the lock until it clicks securely into the closed position.

Looking after your machine
To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
Look after your machine
If your machine is dusty, wipe with a damp lint-free cloth.
Check for blockages in the cleaner head, tools and main body of your machine.
Wash your filter regularly and leave to dry completely.
Don’t use detergents or polishes to clean your machine.
Your serial number
You can find your serial number on your machine, behind the bin. Use your serial number to register your machine

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>