BOSS AUDIO B6ABT 6.5-Inch Two-Way Amplified Roll Cage Speakers User Manual
- June 5, 2024
- BOSS AUDIO
Table of Contents
BOSS AUDIO B6ABT 6.5-Inch Two-Way Amplified Roll Cage Speakers User Manual
B6ABT
6.5” (165 mm) 2-Way Marine/
Powersports Roll Cage/
Waketower Speaker Pods
Congratulations on your purchase of a product.
It has been engineered to bring you the highest level of performance.
Its quality will afford you years of listening pleasure.
Thank you for making ****your choice for audio entertainment!
Specifications
Mid Bass Driver:
6.5” (165 mm )
Poly injection cone
Rubber surround
Tweeter:
1” (25 mm) PEI dome tweeter
Crossover network:
Built-in
Impedance:
4 Ohms
Frequency Response:
140Hz – 20kHz
Sensitivity:
93dB (1 watt/1 meter)
Dimensions (W x H x D):
7.19” x 9.88” x 7.31”
(182 x 250 x 186 mm)
Weight (in gift box):
10.7 lbs (4.85 kg)
Amplifier:
Input Impedance: 10kΩ
Frequency Response: 20Hz – 20kHz
Bluetooth:
Version: 5.0 w/ EDR
A2DP
Range: 33ft (10m)
Network Name: BOSS Audio Systems B6ABT
Introduction
Your new B6ABT waketower speakers are high-power, fully-waterproof 2-way systems featuring 6.5” drivers and a 1” PEI dome tweeter.
**** understands that wake tower speakers are used in many different types of installations. Our versatile mounting solutions give you the ability to attach our wake tower speakers to mounting tubes with diameters of 1.5” – 2” (38 – 51mm)
What is included?
Before you begin installation, please check that your product contains the following contents:
- (2) Speaker pods
- (4) 130x14x2mm rubber mounting strips
- (4) 120x14x1mm rubber mounting strips
- (2) 48x30x2mm rubber mounting pads
- (4) 2″ mounting aluminum bands for 2″ and 1.875″ installation.
- (4) 1.75″ mounting aluminum bands for 1.75″ and 1.5″ installation.
- (4) M6 locknuts
- (4) M6 flat washers
- (4) M6x60mm screws
- (1) Power/speaker wire harness
- (1) 3.5 mm audio cable
Safety considerations when installing
Please remember that these are heavy products that will be installed in a
boating environment. These vehicles can travel at high speeds and be unstable.
So please consider this and use extreme caution. Some safety considerations
include:
- Do not mount the speakers in a location where someone may either walk into or strike their head. During a turbulent ride, please make sure that you do not loosen footing and fall or hit the unit, or it may cause injury.
- Secure the wires to the speakers in multiple locations along their route to your audio source, so that there are no hanging loops of wire. Having un secure wires in any hanging conditions can cause entanglement and injury.
- Tighten the aluminum bands with rubber inserts using care. Do not over compress the rubber inserts. After installation is complete, please recheck all bolts and tighten them further if needed before taking your boat or vessel out for an audio adventure.
- Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.
It is strongly recommended that you work with an assistant to install these speakers.
Installation instructions
STEP 1
To adjust the mounting angle, loosen the metal base of the mounting band by
unbolting the two screws.
Make sure to put all components of the mounting hardware in a safe location.
STEP 2
Twist the metal base to determine the optimal mounting angle for the speaker
on the cage bar. Then secure the metal base by tightening the two screws.
STEP 3
Place a supplied rubber pad (48 x 30 mm) on the metal base of the mounting
band to prevent abrasion and secure clamping.
STEP 4
Place two supplied rubber strips around the cage bar to prevent abrasion and
secure clamping.
Then push two supplied aluminum bands over the cage bar, and align the
aluminum bands with the metal base on the speakers.
STEP 5
As illustrated, secure the aluminum bands to the metal base using a pair of M6
x 60mm screws, M6 flat washers, and M6 locknuts. The locknuts must be
installed into the hex shaped recess on one end of each aluminum band.
Hand-tighten the screws to the degree which allows just enough freedom to
rotate the speaker around the cage bar.
STEP 6
Speaker installation now completes.
Bluetooth
Through Bluetooth connection, you can stream music from a Bluetooth device (e.g. a mobile phone) to the speakers. Make sure Bluetooth is enabled on the device. When the device is in Bluetooth range, it will connect Bluetooth automatically and will be disconnected when it is out of Bluetooth range.
AUX input
Using the supplied 3.5mm audio cable, connect the speaker to your mobile phone for audio input to the speakers. Make sure Bluetooth connection is not made to enable AUX input.
Product dimensions
Wiring
12V wire harness connection
- Connect the RCA plugs (red/white) to an external amplifier for audio output.
- Connect the ACC wire (red) to the accessory power of the vehicle as ON/OFF switch of the speakers.
- Connect the remote out wire (blue) to an external amplifier as ON/OFF switch of the amplifier.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC rules
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF radiation exposure statement
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech
Support:www.bossaudio.com/support
iPod® and iPhonee’ are registered trademarks of Apple, Inc., in the U.S. and
other countries.
The Bluetooth° word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by BOSS Audio Systems is under
license. Other trademarks and trade names are those of their respective
owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>