Shenzhen 2AGA6 SOUNDTANK Ultra-Performance Bluetooth Speaker User Manual

ENQUIRE Soundtrack
Ultra-Performance Bluetooth Speaker Quick Start Guide

Packaging List

Control

Note: Bass effect can be enhanced when the Bass + mode activate [Bass effect can also be largely influenced by the audio quality]. Above control functions can be varied based on different media players.

Light Indicators and Jacks

Light Status when Charging

Note: When the battery is below 20%, low power mode will be activated with the charging light flashing rapidly. The volume will also be decreased in order to preserve the remaining battery.

Power On and Off

Power On
Press and hold the power button for 1 second with Bluetooth light on Bluetooth Light Flashing: Pairing Solid Blue Light: Connected
Power Off
Press and hold the power button for 2 seconds with the Bluetooth light off
Note: Under TWS Stereo Mode, when one speaker is turned off, both speakers will turn off automatically.

Pairing

1. Turn on ENACFIRE Soundtank
2. Select ‘ENACFIRE Soundtank’ from the Bluetooth list
   Note: Please make sure ENACFIRE Soundtank is fully charged and within the effective connection range before connecting

Connect by AUX Audio Cable

When connecting the Soundtrack by the AUX Cable, the below functions will be disabled:

1.  The Bluetooth function will be disabled
2. The track backward and forward function will be disabled
3. The play/pause function will be replaced by unmute/mute function
   Note: The volume control and Bass + Mode is still available

Water-Resistant

Note: The rubber flap needs to be closed at all times to avoid any contamination and be water- resistant The waterproof effect may be reduced if the speaker is damaged or broken as a result of daily use

Incoming Call

The Soundtrack features function for receiving call through smartphones over Bluetooth
Answer Call / End Call
Press  Bluetooth Button Once
Reject Call
Press and Hold **: Bluetooth Button for 2 seconds
Note:** Please keep the Mic as close as possible to achieve better call quality

Q&A

Question 1: Unable to turn on the ENACFIRE Soundtrack?
Answer: Please make sure the ENACFIRE Soundtank is fully charged by using the suggested 5V 1.0A adapter. You can also try to use another USB cable to charge the Soundtank just in case the previous cable is defective.
Question 2: Unable to pair or connect to devices?
Answer: Please follow the below steps to reset the ENACFIRE Soundtrack

1. Turn on ‘ENACFIRE Soundtank’
2. Connect ‘ENACFIRE Soundtank’ to a phone by AUX cable and plug out the AUX cable
3. Double press the Bluetooth button within 10 seconds
4. Turn off ‘ENACFIRE Soundtank’
5. Delete ‘ENACFIRE Soundtank’ from the Bluetooth list
6. Reconnect the ‘ENACFIRE Soundtank’

Q &A
Question 3: No audio when playing the music
Answer: Please make sure the ENACFIRE Soundtank is connected to the correct device, it will automatically connect to the last connected device once it’s turn on. Please also try to use different Apps to play the audio as there might be a glitch happening to the App.
Question 4: There is no response when connecting the ENACFIRE Soundtank to the device by using the 3.5 AUX cable
Answer: Please make sure the 3.5mm audio is fully inserted to the AUX input, you can also try to use another AUX cable just in case the one you used was defective.
How to contact ENACFIRE Customer Service Team.
If you have any issues, please always feel free to contact us through below methods:
US: support@enacfireglobal.com
UK: moongu@enacfireglobal.com
  SCAN QR CODE FOR Quick Guide More Product Information Extended Warranty to 2 Years
http://www.enacfire.com

enacfire.com

|
---|---
http://www.enacfire.com/user/register| http://www.enacfire.com/survey

FCC WARNING STATEMENT

This device complies with Pal 15 Of the FCC Rules. Operation Is subject to the following two conditions:

1. This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
   NOTE 1: This equipment has been tested and found to oomph/ with the limits for a Class B cigild device, pursuant to put 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference wil not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Correct the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE Any changes or modifications to this unit not evnaSSPy approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC WARNING STATEMENT
This device complies with Industry Canada liCenCe-exempt P8SS. Operation is subject to the following two °mations:

1. This device may not cause interference: and
2. This device must accept any interference. inducing interference that may cause undesired operation of the device.
   FCC RADIATION EXPOSURE STATEMENT This equipment complies with FCC radiation exposure knits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits. Human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
   FCC Warning Statement
   Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>