Cixi City Yidong Electronic RCS-13U+RC-13U Remote Control Outlet Instruction Manual

Cixi City Yidong Electronic
RCS-13U+RC-13U Remote Control Outlet
Instruction Manual

SPECIFICATION

Remote Control Outlet
Model: RCS-13U+RC-13U
Voltage: 125VAC, 60Hz
Max.load: 15A Resistive or General purpose, 10A/1250W Tungsten, TV-5, 1/2HP
Remote battery: 1PC CR2032 3V
Radiofrequency: 433.92MHz
Transmitter duty cycle<10%
Receiver category: Class 3
Operation distance: about 80 feet in an open area

DIAGRAM

OPERATION

1. Put the battery in the transmitter.
   Open the battery cover of the transmitter and put a 1PC CR2032 3V battery in it. Then press the ON or OFF button of the transmitter once to check whether it can work.  If the LED indicator turns on, it means this transmitter works well.

2. Plug the receiver into an outlet.
   This receiver is a “grounded” device. It is only intended for use with a three-pronged grounded outlet.

3. Pairing with transmitter
   a. Once the receiver is plugged into the receptacle. The LED indicator in the front right corner of the receiver is slowly flashing.
   Enter into leaning mode.
   Please note: The receiver will exit leaning mode after 29 seconds without any operation. Then please pull the receiver out and put it into the outlet again to pair.
   b. Press the ON button of the transmitter once to pair with the receiver. Once successfully, the LED indicator of the receiver stops flashing and keeps on.
   c.Now you can turn the receiver on/off by pressing the button of the transmitter. The LED indicator of the receiver turns on, which means power is on. In contrast, the power is off.

Clear the pairing

1. Pull the receiver out and put it into the outlet again (the LED indicator is slowly flashing as learning mode).
2. Press the OFF button of the transmitter, then the LED indicator of the receiver flashes quickly (3-4 seconds), which means pairing is cleared. After that, the receiver returns to learning mode. The total time is 29 seconds.
3. Unplug the receiver.
4. The receiver should now be unpaired with the remote

HELPFUL TIPS

1. The transmitted coded pattern is random/learning code. The repeat probability is 1/1,048,575.
2. One receiver can memorize a maximum of 10 different transmitters. If pair the eleventh transmitter, the first paired transmitter will be cleared.
3. One transmitter can pair multiple different receivers and turn them on/off simultaneously.

WARNINGS
Risk of Electric Shock

• Keep children away.
• Do not use in wet locations.
• Do not plug two or more timers together.
• Always ensure the plug of any appliance is fully inserted into the timer outlet.
• If cleaning of the timer is required, remove from mains power and wipe the timer with a dry cloth.
• Do not immerse the timer in water or any other liquid.
• For indoor use only.

Risk of Fire

• Don’t plug in an appliance where the load exceeds rated capacity.
• Do not use extension cords.
• Do not use to control appliances that contain heating elements (cooking appliances, heaters, irons, etc.).

CAUTION:
Do not install/operate this product unless it could be wired with a minimum 15Amp circuit breaker.
Suggestion: Do not plug the device into RCS-13U directly, please use a circuit breaker between these two.
This device complies with Part 15 of the FCC Rules. Operating is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry  Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>