imi IoT JM-LL02 LTE Cat 1 Asset Terminal User Manual

imi IoT JM-LL02 LTE Cat 1 Asset Terminal

PRODUCT OVERVIEW

1. GPS+ LBS positioning
2. Real-time location query
3. Geo-fence alert
4. Vibration alert
5. Tamper alert
6. Strong magnet cover
7. 6,000mAh battery powered
8. Magnetic charging
9. IP67 dust and water-resistant
10. Bluetooth configuration
11. Double MIC

Standard Part List

Specification

Led Indications

Charging

Please charge the device by original charger. It takes about 3 hours to fully charge the device.

Product setup

• Insert SIM card: Please use a screw driver to remove the screws and open the case to insert a SIM card (Size: Nano).
• Power on: Press and hold the ON/OFF button for 3 seconds, and the LEDs will flicker regularly if the device power on successfully.
• Power off: Press and hold the ON/OFF button for 3 seconds and the LEDs will be off in 2 seconds. On/Off button

Note

•  Press the ON/OFF button and the LED will flicker for 15 seconds f the device power on successfully.
•  Press the ON/OFF button and nothing will happen if the device power off successfully.

Configure the device

• Method 1:
  • Use your mobile phone to send commands to the device SIM card number by SMS, please refer details of the commands in Commands list section.
• Method 2:
  •  Download and install the “Jimi loT Lab” app by the following link: http://d.6short.com/Inbr
  •  Make sure the Bluetooth is enabled on your iPhone, choose Connect on landing page.
  • Power on LLO2 and then short press the power button for 3 times, the device name will automatically show on Connect page, tap on it to connect.
  •  After the device is connected successfully, you can view the basic data of the device, click “Command mode” button at the bottom can enter the command setting page.
  • Type and send the command to query and and make configurations. The device has no password by default, you can set password (See details in command list) to secure the device. If the password has been set, each command will need to be sent with the password filled.
  • In “Jimi loT Lab” app landing page, you can create a template with multiple commands in Presets page, when the device is connected you can tap the “Upload preset’ button instead to send multiple commands that you created in Presets at a time.

**COMMAND LIST

**

Voice monitoring
When center number sends monitor command: MONITOR# to the device, the device will reply “OK” and call the center number. After the call connected, the terminal will enter monitor condition. The center number can hear the sound around the device. For more operation, please refer to the command list section.

Installation recommendation

•  The device should face up to the sky.
•  Metal thermal barrier or heating layer of the windshield affects the signal. Please change installation position to receive better signal.

Web Platform & App

• Please login the designated service platform provided by your distributor to track and operate the device.
•  Please download and install the APP in designated website, iOS App store or Google Play store

Warranty instructions and service

•  The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. We reserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer.
•  Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself.
•  Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service centre.
•  Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.
•  The warranty is not applicable to cases other than defects in material, design and workmanship.

Maintenance Record

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated it minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Troubleshooting

FCC Rules

Note: This equipment has been tested and found to comply with the limits tor a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonadie protection against harmful interference in a residental installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interterence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct ne interference Dy one or more or the following measures

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for Help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>