Shenzhen JC400 EdgeCam User Manual

Shenzhen JC400 EdgeCam User Manual

Please read this manual carefully prior ta use. The content of this manual may change due to improvement in performance without prior notice.

1. Introduction

1.1 Packing List

Please check the product model you purchased carefully as the packing list varies with the model.

1.2 Overview

JC400 series uses4G ne1workfor communication. For these dual channel digital video recorders (DVRs}, except to be able to record simultaneously, the two cameras can also record locally and live stream remotely at the same time. The front-facing HD camera is used for real-time recording; while the cabin-view camera with IR LED for monitoring at night time. Combined with DMS, driving behaviour analysis, multiple alert options, and much more, they can assist the management in monitoring the vehicle condition and the driver’s behaviour at any time. This is very useful to coach driver’s behaviour, improve management efficiency, and lower operation cost, making JC400 series an ideal option for remotely managing ridesharing, rental, public, government, and enterprise fleets.

1.3 Appearance and LEDs

1.3.1 Main Unit

1.3.3 LEDs

1.4 Wirings

2. Specifications and Features

2 .1 Specifications

2.2 Features

3. Installation

Precautions:

1. This device is not suitable for battery electric vehicles (BEVs) and hybrid electric vehicles (HEVs).
2. Use accessories specified by the manufacturer only.
3. The standard supply for the device is DC9- 30V, please use the original power cable and ensure that the positive and negative ends are correctly wired.
4. Remove the protective film on 1he remote camera prior to installation.
5. It is recommended to ask a distributor, a designated business, or an expert to do the installation and commissioning.

3.1 Preparation

Device check
Check visually whether the device is in good condition and whether the relevant accessories are complete.

3.2 SIM Card Attachment

Ensure that the device is ACC OFF before attaching a proper SIM card.

To attach and detach the SIM may damage the contacts, please use the completed Micro SIM card instead. In addition, the SIM should have data service activated and not in arrears.

3.3 TF Card Attachment

Ensure tha1the device is ACC OFF before attaching a proper TF card.

Note:

1. Use a TF card in speed class 10 or higher and with a capacityof16GB or above.
2. The TF card is recommended to change every half a year to ensure the recording performance of the device.
3. Mount the tamper cover after the attachment.

Fit the TF card in the correct slot.

3.4 Main Unit Installation

1. 1.Connect the power cable of the device to B+, ACC, and GND of the fuse box on the vehicle. (1) is a reference position.

2. Route the power cable along the A pillar of the vehicle to the upper center of the front windshield. The red dashed line(2) in the figure is for reference.

3. Select a proper installation position and wipe the position c lean. Remove the protective film from the 3M tape of the mounting base and attach it to the position. Wait for 2 hours before proceeding to the nex1 step. See (3) for reference.

4. Mount the device to the base and connect its power cable correctly (see (4) for reference). Then fasten the cable securely.

3.5 Installation of Accessories

You can select a proper position to install the remote camera according to actual conditions.

3.5.1 Remote AHD Camera

1. Face the camera inward and install it to the windshield behind the rear-view mirror (as shown in (1) )or to the  of the dashboard (as shown in (2)). Wipe a selected position clean, remove the protective film from the 3M tape, and attach the device.
2. Use the supplied screwdriver to tighten the screw of the camera, so it keeps at the best angle. Connect the cables correctly and fasten them securely.

3.5.2 DMS Camera

This section Is dedicated to JC4000.
The DMS camera is mainly used far monitoring the driver. Fixate the camera at an angle about 30′ to the steering wheel directly facing the driver’s head, as the following figure shows.

3.5.3 Other Accessories

1. External battery
   It is used ta power the device for a while after its main supply is cut off. Connect the external battery to the corresponding interface on the device and place it in a proper position (such as O in the above figure).

2. SOS key
   It is used1o seek help in emergencies. Connect the SOS key to the corresponding interface on the device, remove the protective film from the 3M tape, and then attach it to a proper position (such asf) in the above figure).

3. Relay
   It is used to cut off the power and fuel of the vehicle remotely to force it to stop. Connect it to the corresponding interlace on the device and place it in a proper position, such as it in the above figure. For wiring details, sae1.4.

4. RS232 (optional)
   It is used1o connect to an external device for function expansion when a scenario requires a feature that cannot be offered by the device. (4) is a reference installation position.

Note:

1. Choose proper accessories based on your actual needs.
2. Select a relay that goes perfectly with the battery of your vehicle.
3. It is recommended to ask a distributor, a designated business, or an expert to do the installation and commissioning.

3.6 Commissioning

4. Platform Operations

4.1 Installation

4.1.1 Platform

Scan the QR code on the right with the browser of your mobile phone to download and install the app.http://onelink.to/fcv8w4

4.1.2 Calibration Tool for JC4000

https://resadmin.blob.core.windows.net/other/dms.apk

Scan the QR coda on the left with the browser of your mobile phone to download and install 1he calibration tool.

Note:
This app is used for feature calibration of JC400D.
This calibration tool is only compatible with mobiles with Android OS.

4.2 Operation Guide

Seen the QR code on1he right with the browser of your mobile phone to view relevant operations.https://www.jimilab.com/upfilesimg/file/15965223110.pdf

5. Others

5.1 Battery Safety

1. Use the original battery supplied by the manufacturer only. The use of any non-original accessories may damage the device, in which case the manufacturer will assume no repair liabilities for such damages.
2. Avoid metal objects as they may cause short circuits on battery contacts.
3. Do not remove the cover of the battery.
4. Do not soak the battery in water or expose it to fire.
5. It is forbidden to use batteries that are deformed, discoloured, spilled, or package-damaged. If such an except ion, such as overtemperature, deformation, discoloration, spillage, etc., occurs during use, charging, or storage of the battery, please stop using the device immediately and contact the attar sales center for a replacement.
6. It is forbidden to dismantle, or modify, or charge (in any other method other than stated) the battery.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>