FUTURECOM DVRSUHF DVRS Vehicular Repeater User Manual
- June 5, 2024
- FUTURECOM
Table of Contents
FUTURECOM DVRSUHF DVRS Vehicular Repeater
Notes, Attentions, Important
Throughout this manual, you will see Notes, and Attentions, Important Their meaning is as follows:
NOTE
A clarifying statement that expands oan the text that follows.
IMPORTANT
An important statement that should be considered and / or implemented in order
to achieve adequate equipment operation.
ATTENTION!
An instruction that must be followed in insure compliance with the appropriate
standards or proper equipment operations.
INTRODUCTION
The Futurecom DVRS® Vehicular Repeater is designed to interface to a range of mobile radios and control heads. It permits expanded operation of portable radios. The Vehicular Repeater system consists of. a mobile radio, DVRS® Vehicular Repeater unit, a mobile radio Control Head and a RF multiplexer. The Control Head communicates with the Vehicular Repeater and the mobile using a serial data protocol.
REPEATER MODES
The Vehicular Repeater operates in one of three modes. The mode of operation
is selectable from the Mobile Control Head by the mobile radio operator. The
three modes are known as the MOBILE, LOCAL and SYSTEM modes. The function and
purpose of each mode is described as follows.
Mobile Mode
In the MOBILE mode, the vehicular repeater is completely disabled. The mobile
radio is operational and will permit the mobile radio user to communicate
conventionally, using the mobile radio. The mobile user may select the desired
mobile operating channel, adjust the receiver volume level and transmit using
the microphone Push-to-Talk (PTT). This mode is used when Repeater operation
is not desired. The Vehicular Repeater System operates similarly to a standard
mobile radio system, as if the Repeater were not present. The RF multiplexer
is disabled and the antenna is connected directly to the mobile radio. The
MOBILE mode should be selected if several Repeater equipped vehicles are in
the same area and another Vehicular Repeater already has LOCAL or SYSTEM mode
enabled.
Local Repeat Mode
In the LOCAL repeat mode, the Vehicular Repeater is enabled to permit
communications among nearby portable radio users and the mobile radio user.
Repeater signals are not retransmitted by the Mobile Radio, so that
communications on the mobile channel will not be disturbed. However, all
functions of the mobile radio operate normally, except for scan, microphone
mobile Push-to-Talk, scan activation, mode selection, zone selection, home
channel operation and mobile channel selection. When the LOCAL repeat mode is
selected, the mobile radio scan is deactivated and the mobile radio reverts to
the selected mobile channel. Signals received by the Vehicular Repeater
receiver are heard in the mobile speaker and will also be retransmitted by the
Vehicular Repeater transmitter. Signals received by the Mobile receiver are
heard in the Mobile speaker and will be transmitted by the Vehicular Repeater.
When signals are present in both the Vehicular Repeater and Mobile receivers
simultaneously, the signal from the Vehicular Repeater will have priority in
the mobile speaker.
(Note that the receiver/PTT and speaker priorities are programmable.) The mobile user will key only the Vehicular Repeater transmitter when using the microphone Push-to-Talk. The Vehicular Repeater receiver has full priority over the mobile radio operator microphone Push-to-Talk. To respond to a mobile signal, the mobile operator must enter either the MOBILE or SYSTEM mode to be able to transmit from the mobile radio. The mobile user may adjust the receiver volume level and transmit over the Vehicular Repeater using the microphone Push-to-Talk. The LOCAL mode, as the name implies, permits communications among portable radio users and the mobile radio operator, without interfering with the mobile radio dispatch channels.
System Repeat Mode
In the SYSTEM repeat mode, both the Mobile Radio and the Vehicular Repeater
are enabled at the same time to permit the full exchange of communications
among nearby portable radio users, the mobile radio user and the dispatcher
and other users on the Mobile Radio channel. Signals received by the Vehicular
Repeater receiver are heard in the mobile speaker and may also be
retransmitted by both the Vehicular Repeater and Mobile transmitters at the
same time. Signals received by the Mobile receiver are heard in the mobile
radio speaker and are also retransmitted out of the Vehicular Repeater
transmitter. When the SYSTEM repeat mode is selected, the mobile radio scan
may be deactivated and the mobile radio reverts to the selected mobile
channel. When signals are present in both the Vehicular Repeater and Mobile
receivers simultaneously, the signal from the Mobile Radio will have priority
in the mobile speaker.
The mobile user may simultaneously key both the Mobile radio and Vehicular
Repeater transmitters when using the microphone Push-to-Talk. The mobile radio
operator microphone Push-to-Talk has priority over the Mobile receiver.
When signals are present in both the Vehicular Repeater and Mobile receivers
simultaneously, the signal from the Vehicular Repeater has priority in the
mobile speaker. The mobile user may adjust the receiver volume level and
transmit over the Vehicular Repeater and Mobile Radio, using the microphone
Push-to-Talk.
CONTROL HEAD
The control unit is a standard mobile radio control head. The Vehicular Repeater is designed to operate with a variety of control heads. It is a ruggedly constructed weatherized control unit, incorporating an array of pushbuttons, a Liquid Crystal display, 2 knobs and 2 LED indicators. The display and pushbuttons are backlit for night time visibility. The control unit is housed in a two-piece plastic, weather-resistant housing. The external radio/repeater connections are made to connector on the rear of the unit. A microphone is provided and is secured to the control unit connector on the front of the control unit. A serial-control data interface is used to provide a communications connection between the control unit, the Vehicular Repeater and the mobile radio.
The following features are provided:
Knobs for:
- ‘Volume’ with integral Power On/Off pushbutton switch
- ‘Channel’ selection
Pushbuttons for:
- ‘Zone’
- ‘Page’
- ‘Monitor’ ON/OFF
- ‘Alarm’
- ‘Private’
- ‘Repeater mode’ selection (H/L) ‘Phon’
- ‘Scan’
- ‘Call’
LED Indicators for:
- ‘Mobile Transmit’ (Red LED)
- ‘Mobile Receiver Busy’ (Orange LED)
Display:
Alphanumeric LCD (with backlighting) Indicators are provided to display the
receiver and transmitter status of the mobile. The ‘Mobile Transmit’ red
indicator lights whenever the mobile transmitter is keyed. The ‘Mobile
Receiver Busy’ orange indicator lights whenever the receiver is busy,
regardless of presence or absence of any CTCSS (Channel-Guard) tone coding.
REPEATER RADIO UNIT
The Repeater is designed to implement a Vehicular Repeater System, to provide
portable radio users greater communication range by repeating signals through
the vehicle’s mobile radio to the dispatch centre. Various modes of repeater
operation are available, to suit different operational requirements. The
Vehicular Repeater Radio is the central connection point for the vehicular
system. It connects to an external Control Head and Mobile Radio. It includes
all the necessary hardware for repeater operations. The Repeater is housed in
a weather resistant metal enclosure with 2 removable covers. The covers
provide protection for the connectors. The Repeater is mounted on a RF
multiplexer. The Repeater communicates with the control head and the mobile
radio via serial communication bus.
MOBILE RADIO UNIT
The Mobile Radio used in the Vehicular Repeater System is a standard mobile
radio. Refer to the mobile radio’s user manual for details of operation of
this radio. The Vehicular Repeater is designed to operate with a variety of
mobile radio units.
OPERATION
CONTROL HEAD
The Repeater Control Head selects mode of operation for both the Repeater
and the Mobile Radio.
To Turn the Repeater ON or OFF
Press the button in the Volume knob located on the left side of the control
unit. The display should become active when the system turns ON. A test
message appears briefly on the display. When the system is turned ON, the
Mobile Channel and Repeater Mode will automatically return to the same
settings that were in effect when the power was last turned OFF. Press the
button in the Volume knob second time to turn the Repeater OFF.
To Change the Speaker Volume
Turn the Volume knob until the desired volume level is reached.
To Change the Repeater Mode
Press the ‘H/L’ button once. The Repeater mode is changed in the following
sequence: MOBILE-SYSTEM-LOCAL-… In the Mobile mode the alphanumeric display
shows ‘ZONE CHANNEL’. In the System mode both the Repeater and the Mobile
Radio may transmit at the same time. In the Local mode the display shows ‘RLOC
CHANNEL’. (‘ZONE’ is the selected Mobile zone name while ‘CHANNEL’ is the
selected Mobile channel name.) When the LOCAL or SYSTEM repeat modes are
selected, the mobile radio scan is deactivated and the mobile radio reverts to
the selected mobile channel.
NOTE
The Mobile zone and channel cannot be changed while in LOCAL and SYSTEM repeat
modes.
MOBILE XMIT Status Indicator
The ‘MOBILE XMIT’ red LED indicator is one of two status indicators that is
provided on the Control Head, located in the upper left corner. This indicator
will light whenever the Mobile Transmitter is keyed. This will occur in
‘MOBILE’ or ‘SYSTEM’ mode when the microphone Push-to-Talk is being pressed or
when a signal from the Vehicular Repeater is being retransmitted by the Mobile
Radio (In ‘SYSTEM’ mode).
MOBILE BUSY Status Indicator
The ‘MOBILE BUSY’ orange LED indicator is one of two status indicators that
are provided on the Control Head, located in the upper left corner. This
indicator will light whenever the Mobile Radio is receiving any signal on the
selected Mobile Channel. If CTCSS (Channel Guard) tone coding is used, the
signal may not be audible if the coding does not match. Note that if the
microphone is “off-hook”, the Mobile/Repeater audio will be heard on the
speaker even if CTCSS is not present or is incorrect. This is the same as the
Monitor function.
ALPHANUMERIC Status Indication
The ‘ZONE’ is not displayed in the LOCAL and SYSTEM repeat modes. Instead,
this portion of the alphanumeric display shows the status of the Repeater in
these two modes together with ‘MOBILE XMIT’ and ‘MOBILE BUSY’ status
indicators.
CONTROL HEAD INDICATORS AND ALPHANUMERIC DISPLAY – MOBILE MODE
REPEATER STATE| ‘MOBILE BUSY’| ‘MOBILE XMIT’|
DISPLAY
---|---|---|---
MOBILE RECEIVE WITH CTCSS| ON| | ‘ZONE CHANNEL’
MOBILE RECEIVE WITHOUT CTCSS| ON| | ‘ZONE CHANNEL’
MICROPHONE PTT| | ON| ‘ZONE CHANNEL’
REPEATER RECEIVE WITH CTCSS| | | ‘ZONE CHANNEL’
REPEATER RECEIVE WITHOUT CTCSS| | | ‘ZONE CHANNEL’
CONTROL HEAD INDICATORS AND ALPHANUMERIC DISPLAY – LOCAL MODE
REPEATER STATE| ‘MOBILE BUSY’| ‘MOBILE XMIT’|
DISPLAY
---|---|---|---
MOBILE RECEIVE WITH CTCSS| ON| | ‘RL TX CHANNEL’
MOBILE RECEIVE WITHOUT CTCSS| ON| | ‘RLOC CHANNEL’
MICROPHONE PTT| | | ‘RL TX CHANNEL’
REPEATER RECEIVE WITH CTCSS| | | ‘RL RT CHANNEL’
REPEATER RECEIVE WITHOUT CTCSS| | | ‘RL RX CHANNEL’
CONTROL HEAD INDICATORS AND ALPHANUMERIC DISPLAY – SYSTEM MODE
REPEATER STATE| ‘MOBILE BUSY’| ‘MOBILE XMIT’|
DISPLAY
---|---|---|---
MOBILE RECEIVE WITH CTCSS| ON| | ‘RS TX CHANNEL’
MOBILE RECEIVE WITHOUT CTCSS| ON| | ‘RSYS CHANNEL’
MICROPHONE PTT| | ON| ‘RS TX CHANNEL’
REPEATER RECEIVE WITH CTCSS| | ON| ‘RS RT CHANNEL’
REPEATER RECEIVE WITHOUT CTCSS| | | ‘RS RX CHANNEL’
Note that ‘ZONE’ and ‘CHANNEL’ are the selected Mobile zone and channel names, respectively.
Functions Disabled in LOCAL and SYSTEM Repeat Modes
There are several control unit button and knob functions, which are disabled
in the LOCAL and SYSTEM repeat modes. These are Scan activation, Mode
selection, Zone selection, Home channel operation and Mobile channel
selection.
NOTE
A standard audible error signal “bop” as well as an error message is displayed
‘RLOC VR ACTIVE’ or ‘RSYS VR ACTIVE’ if any of the above functions are
attempted in the LOCAL or SYSTEM repeat modes.
Other Button and Knob Functions
The available Repeater functions are:
- ‘Monitor’ – unmutes speaker audio when Mobile or Repeater RF carrier is present.
- ‘H/C’ – changes Repeat mode of operation.
- ‘Call’ – sends call signal via Mobile transmission (SYSTEM and MOBILE mode only).
- ‘Opt’ – dims alphanumeric display.
All other buttons and knobs function as programmed in the standard mobile radio. Please refer to the mobile radio’s documentation for details of operation.
APPENDIX 1
General Specifications| |
---|---|---
Dimensions Height / Width / Depth| 92mm (3.63”) / 186mm (7.32”) / 315mm (
12.41”)
Weight| 5.2 kg (11.5 lbs) approx.
Channel Spacing| 12.5 kHz or 25 kHz
| Analog Voice or P25 Modulation
Power Supply| 13.8 VDC ± 20%, negative ground only
DC Current Drain| Repeater OFF| Max. 0.01 A
| RPTR Standby| Max. 0.8 A
| Receive| Max 1.7 A @ 7.5 W Audio @ 13.8 VDC
| Transmit| Max. 6.0 A @ 20 W RF output at TX Connector
Operating Temperature| -30°C to +60°C
Protection Against Liquids| IP6 (water jet proof)
RF Connector Impedance| 50 Ohm
Duty Cycle|
VHF, UHF| 50% TX – 50% RX
700MHz, 800MHz| 100% TX
External Connectors| ****
TNC female
USB, 9 pin male circular (programming only) 20 pin male circular:
RS232: 115 kbps max., +/-3V min. input, 5 kOhm input impedance, 300 Ohm output impedance
Analogue audio ports: 200 kOhm input impedance, 15 Ohm output impedance
6 pin male circular
RF Connectors
Computer Interface
Mobile Radio
DC Power
Power Output at TX Connector|
Standalone Mode:| 20 W Max. (programmable per channel from 1 W Min.)
FCC Simultaneous DVRS Repeated
and Mobile Operation:
| 5W, 6W, 10W or 20W Max. (programmable per channel from 1 W Min.)
| Refer to RF Safety Booklet for maximum allowed power
output for specific approved DVRS, Mobile Radio and antenna combinations
| Maximum DVRS power output is programmed by authorized service personnel at time of DVRS installation in accordance with approved DVRS, Mobile Radio and antenna combinations.
Power output cannot be changed by the operator
---|---
CCT Option| 15 sec to 15 min. or disabled
Carrier Frequency Stability| ± 1.5 ppm, from –30° to +60°C, ambient +25°C
reference
Audio Distortion| <2%
Frequency Band (RX and TX)|
VHF FCC| 136 – 174 MHz
VHF IC| 138 – 174 MHz
UHF FCC| 380 – 406 MHz, 406.1 – 512 MHz
UHF IC| 406.1 – 430 MHz, 450 – 470 MHz
700MHz FCC| 764 – 776 MHz, 794 – 806 MHz
700MHz IC| 768 – 776 MHz, 798 – 806 MHz
800MHz FCC| 806 – 824 MHz, 851 – 869 MHz
800MHz IC| 806 – 824 MHz, 851 – 869 MHz
Equipment Type Acceptance|
VHF FCC| LO6-DVRSVHF
UHF FCC| LO6-DVRSUHF
700MHz FCC| LO6-DVRS700
800MHz FCC| LO6-DVRS800
VHF IC| 2098B-DVRSVHF
UHF IC| 2098B-DVRSUHF
700MHz IC| 2098B-DVRS700
800MHz IC| 2098B-DVRS800
Applicable Standards| Test
---|---
MIL-STD 810C,D,E,F| For rain, dust and salt atmospheres
MIL-STD 810C,D,E,F| For shock and vibration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>