BOSS AUDIO MPWT60RGB 6.5 Inch 2 Way 600W Marine WakeTower Speakers User Manual

BOSS AUDIO MPWT60RGB 6.5 Inch 2 Way 600W Marine WakeTower Speakers User Manual

MPWT60RGB
6.5” (165 mm) 2-Way Marine/ Powersports Roll Cage/ Waketower Speaker Pods

Congratulations on your purchase of a product.

It has been engineered to bring you the highest level of performance.
Its quality will afford you years of listening pleasure.

Thank you for making   ** your choice for audio entertainment!**

Specifications

Mid Bass Driver:
6.5” (165 mm )
Poly injection cone Rubber surround

Tweeter:
1” (25 mm) PEI dome tweeter

Crossover network:
Built-in

Impedance:
4 Ohms

Power Handling:
600 Watts (MAX)

Frequency Response:
140Hz – 20kHz

Sensitivity:
93dB (1 watt/1 meter)

Dimensions (W x H x D):
7.17” x 9.84” x 7.32”
(182 x 250 x 186 mm)

Weight (in gift box):
9.8 lbs (4.45 kg)

Introduction

Your new MPWT60RGB waketower speakers are high-power, fully-waterproof 2-way systems featuring 6.5” drivers and a 1” PEI dome tweeter. Both speakers have LED lights which can be controlled by the supplied remote control.

**** understands that wake tower speakers are used in many different types of installations. Our versatile mounting solutions give you the ability to attach our wake tower speakers to mounting tubes with diameters of 1.5” – 2” (38 – 51mm)

What is included?

Before you begin installation, please check that your product contains the following contents:

• (2) Speaker pods with male LED connector
• (4) 130x14x2mm rubber mounting strips
• (4) 120x14x1mm rubber mounting strips
• (2) 48x30x2mm rubber mounting pads
• (4) M6x60mm screws
• (4) 2″ mounting aluminum bands for 2″ and 1.875″ installation
• (4) 1.75″ mounting aluminum bands for 1.75″ and 1.5″ installation
• (4) M6 locknuts
• (4) M6 flat washers
• (1) LED power wire
• (1) LED connection wire with female connector
• (1) Remote control
• (1) Keychain tag

Safety considerations when installing

Please remember that these are heavy products that will be installed in a boating environment. These vehicles can travel at high speeds and be unstable. So please consider this and use extreme caution.

Some safety considerations include:

1. Do not mount the speakers in a location where someone may either walk into or strike their head. During a turbulent ride, please make sure that you do not loosen footing and fall or hit the unit, or it may cause injury.
2. Secure the wires to the speakers in multiple locations along their route to your audio source, so that there are no hanging loops of wire. Having unsecure wires in any hanging conditions can cause entanglement and injury.
3. Tighten the aluminum bands with rubber inserts using care. Do not over compress the rubber inserts. After installation is complete, please recheck all bolts and tighten them further if needed before taking your boat or vessel out for an audio adventure.
4. Do not install these speakers where they may block the view of the pilot and prevent safe operation of the vessel or vehicle.

It is strongly recommended that you work with an assistant to install these speakers.

Installation instructions

STEP 1

To adjust the mounting angle, loosen the metal base of the mounting band by unbolting the two screws.
Make sure to put all components of the mounting hardware in a safe location.

STEP 2

STEP 3

Place a supplied rubber (48 x 30 mm) pad on the metal base of the mounting band to prevent abrasion and secure clamping.

STEP 4

Place a supplied rubber strip around the cage bar to prevent abrasion and secure clamping.
Then push two supplied aluminum bands over the cage bar, and align the aluminum bands with the metal base on the speakers.

STEP 5

As illustrated, secure the aluminum bands to the metal base using a pair of M6 x 60mm screws, M6 flat washers, and M6 locknuts. The locknuts must be installed into the hex shaped recess on one end of each aluminum band.
Hand-tighten the screws to the degree which allows just enough freedom to rotate the speaker around the cage bar.

STEP 6

Speaker installation now completes.

Wiring

Tip:

You may also connect the LED power wire to the vehicle accessory power (red color to the positive wire of accessory power and black to the negative wire of accessory power)

Warning:

• For safety, disconnect the negative terminal from the source battery prior to wiring.
• Note your amplifier impedance stability prior to wiring.
• Use only high quality marine-grade speaker wires.
  Make sure wires are not squeezed or damaged by sharp edges.

1. LED wire connection
   Using the supplied LED connection wire with female connector, connect the two speakers through the male LED connectors.

2. Speaker wire connection
   Using speaker wires (not included) , connect the two speakers to the audio outputs on your 12VDC amplifier.
   Make sure to observe polarity.

3. LED power connection
   Connect one end of the supplied LED power wire to the power input on the speaker, and the other end to the 12VDC source battery (red color to the positive terminal, black to the negative terminal).

LED light control

The product comes with a remote control for you to control the RGB LED lights on both speakers.
Keep the remote control safely using the supplied key chain tag.

1. Power on/off
   Turn on or off illumination. Make sure the LED power wire is connected to the source battery.

2. MODE +/-
   Switch from static to dynamic illumination and select a dynamic illumination pattern.

3. SPEED +/-
   For dynamic illumination, select a dynamic illumination speed.

4. COLOR +/-
   Switch from dynamic to static illumination and select an
   illumination color.

5. BRIGHT +/-
   For static illumination, change the illumination intensity.

6. DEMO
   Cycle through red, green and blue illumination.

Battery replacement

The remote control is powered by a CR2025 coin battery. If the battery is depleted, replace it with a new CR2025 coin battery.

1. Find the battery compartment at the back of the remote control. Pull the battery tray out.
2. Load a new battery with correct polarity as shown on the tray.
3. Replace the battery tray. Make sure the tray is securely inserted.

Important notes on battery

• Danger of explosion if the battery is incorrectly replaced. Replace only with the same type or equivalent type. Observe correct polarity while inserting the battery.
• Do not leave the battery near fire or under direct sunlight. Do not place the remote control in hot places (e.g. on the dashboard). This may cause fire, explosion or excessive heat.
• Remove the battery from the remote control if it is not used for a long time to avoid battery leakage.
• Do not recharge, dismantle or short-circuit the battery or throw it into fire. This may cause a risk of explosion or battery leakage. If spilled fluid comes in contact with your skin or clothing, immediately rinse with water and consult a doctor.
• The remote control contains a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.

BOSS Audio System
3451 Lunar Court . Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support:  www.bossaudio.com/support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>