BOSS AUDIO 609UAB 200W Bluetooth Single Din MP3 Compatible Digital Media AM or FM Receiver User Manual

AUDIO SYSTEMS
609UAB
USER’S MANUAL
BLUETOOTH° I 200 WATTS I SINGLE-DIN
MP3-COMPATIBLE DIGITAL MEDIA AM/FM RECEIVER

PRECAUTIONS

Lithium Battery Cell Warnings

• Cell leakage may cause damage to the remote control.
• Do not throw cells into fire, as this may cause an explosion.
• Keep battery cells out of reach of children.

Use cautions

• To reduce the risk of fire, electric shock, and annoying interference, do not repair yourself. Please refer serving to a qualified person.
• Some MP3/WMA files may not be playable.
• Keep lower volumes to concentrate on traffic and road conditions.
• If the battery is disconnected or discharged or changed, the preset memory will be erased and must be reprogrammed.
• Installation of unit is better at a horizontal position, or if it is at an angle, it may be not working at its best situation.
• Be sure to lower the volume before switching off the unit or the ignition key.
• The use of apparatus in moderate climates.
• The symbol indicates DC voltage.

CAUTION
For coin/button battery used, please refer for further information to the user manual.
Attention should be drawn to the environmental aspects of battery disposal.
CAUTION
The danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type.
The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING
Do not ingest the battery, Chemical Burn Hazard (The remote control supplied with) This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

INSTALLATION

Installation Procedures
First complete the electrical connections and then check for correctness.
Installation Opening
This unit can be installed in any dashboard Having an opening as shown below.

Insert the mounting collar into the dashboard and bend the mounting tabs out with a screwdriver.
Make sure that lock lever is flush with the mounting collar( not projecting outward).

INSTALLATION(CONT.)
Connect all wiring harness and slide the head unit into the mounting collar until it clicks into place.
Wiring Connections

**** – Only support speakers of 4 ohms or above.
– The maximum current of the auto antenna is 200mA.
– The equipment shall be protected by the circuit with max. 10 Amperes of the front end of DC source.

Uninstall the Main Unit

1.  Remove the plastic trim out from the main unit.
2.  Insert a bracket key into the left and right side of the main unit and draw the unit out of the mounting sleeve.

Overview of the Components

1. OFF(power On/Off) / SRC (source) button
2. VOL (volume) knob and SEL (select/menu) button
3. Hands-free Microphone
4. LCD Display
5. Reset button
6. USB Port
7. BAND button
8. (tune/ seek up, next track, fast forward) button
9. (automatic store / preset station scan, automatic music search) button
10.  MUTE button
11. (Answer Call / End Call) button
12.  IR remote sensor
13. **** (pause/play), Preset station 1 button
14.  INT (intro), Preset station 2 button
15.  RPT (repeat), Preset station 3 button
16. (Push-To-Talk) button
17. RDM (random), Preset station 4 button
18. -10(previous 10 tracks), previous folder, Preset station 5 button
19. +10(next 10 tracks), next folder, Preset station 6 button
20. AUX IN (auxiliary input) jack
21. CLOCK(clock setting) button
22.  (tune/seek down, previous track, fast reverse) button

General Operation
Turn Unit on/off, Change the Source

• Press the -OFF/SRC button to turn on the unit. Press and hold the -OFF/ SRC button to turn off the unit.
• Press the -OFF/SRC button to select the different modes: Radio, USB(with USB device inserted), AUX-IN(auxiliary input) and BT(Bluetooth) modes.

Adjust the volume (VOL)
Rotate the VOL knob to increase or decrease the volume level.

General Operation

Adjust Menu Options (SEL)

• Press SEL button repeatedly to cycle through the following adjustable audio functions:
  – ILL MID/HI/LOW: This receiver is equipped with 3 brightness settings.
  – BASS/TREBLE:-7, -6, ~, 1, 0, +1,~, +6, +7
  Note: BASS and TREBLE settings are only enabled when EQ setting is turned OFF.
  – BALANCE:L7, L6,~, L1, L=R, R1,~,R6, R7
  – FADER:R7, R6, ~, R1, 0, F1, ~ ,F6, F7
  – EQ(Equalizer) Setting: OFF, CLASS, ROCK, POP, FLAT
  – Loudness: LOUD ON/OFF
  – DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).
  – Stereo/Mono: Switches between MONO and STEREO reception mode for radio frequencies.
  – CLOCK 12/24: Select between 12 hours and 24 hours display.
  Note: If 12-hour display is selected , AM= Morning; PM= Afternoon
  – AREA US/EU: This car radio is equipped the USA / Europe frequency.
  Rotate the volume knob to switch between USA and Europe frequency.
  The system will change the frequency setting in about 3 seconds.

• Rotate the VOL knob to adjust the selected item.

Setting the Clock
Press the CLOCK button to display time. Press and hold the CLOCK button, the hour’s digits start flashing on the display. Set hours by rotating the VOL knob. Briefly press the CLOCK button. The minute digits start flashing. Set minutes by rotating the VOL knob. Finally, press the CLOCK button to confirm your settings.

LCD Display
Mute On/Off
In power-on mode, briefly press the MUTE button to toggle mute on or off.
USB Port
Hands-free Microphone
Auxiliary Input Jack
Reset
Push the RESET button with a thin object with a pointed end to reset all parameters to factory default settings.This function may be used when the LCD does not display normally or sound is distorted, or when any of controls are disabled.

Radio Operation

Switch Between USA area and Europe area Frequency
In radio mode, press the SEL button to enter the switch state of the US (USA) and EU(europe)frequency, then rotate it to switch between US(USA) and EU(europe) frequency. The system will change the frequency setting in about 3 seconds.
Change Bands
In radio mode, shortly press the BAND button to switch between the FM1(F1), FM2(F2), FM3(F3) and AM1(A1), AM2(A2) bands.
To Store / Recall Preset Stations
The radio can be stored 6 preset stations for each band (FM1, FM2, FM3, AM1 and AM2) for atotal of 30 preset stations.
– To memorize a station:
Press and hold the desired preset buttons (1-6) to save a radio station.
– To recall a preset station:
Briefly press the respective station button (1-6) to recall the corresponding preset station.
Manual Tuning
In the radio mode: Press and hold the or button to enter the manual tuning mode. In manual tuning mode, briefly press the or button to search the next or previous frequency step by step.
Seek Tuning
In radio mode, press the   or button, the automatic search will start, it will search upward or downward for the strong signal radio station within the current band. The auto searching will stop until find a station.
Automatic Store Station / preset station scan ( )
Press and hold the button to store 18 FM stations and 12 AM stations automatically.
Briefly press the button to recall each preset station that is stored in the memories in each band.

LOCAL/DX
In urban areas, most stations are strong enough and the “LOCAL ON” mode should be selected. Switch to LOCAL OFF mode to search for stations with weaker signals. Press the LOC button on the remote control to choose local or distant reception mode.
STEREO/MONO
FM station is received in stereo mode. However, if the signal is weak or reception is not asgood as you would like, switching to MONO mode usually improves the overall sound quality. Press the ST button on the remote control to choose FM STEREO or MONO audio effect.

USB Operation

Play MP3/WMA music inside a USB stick.
Insert the USB stick with MP3/WMA music into the USB port, it will play automatically.Note: the USB port also supports charging mobile phones, the maximum charging ability is 5V / 1A.
Select Next Track or Previous Track
In the USB mode, briefly press the or button to play the next or previous track.
Fast Forward/Reverse
Press and hold the or button to fast forward or reverse a track.
Play / Pause
Press the ** button to interrupt the playback of music (pause function).
Press this button again to continue the playback.
Introduction Scan
Press the INT button to play the first 10 seconds of all tracks.
Press again to stop the introduction scan, and play the current track.
Repeating the track
Press the RPT button to toggle between RPT ALL (Play all tracks), RPT FLR (Continuously repeat all tracks in the current folder) and RPT ONE (Continuously repeat current track).
Playing all tracks in random
Press RDM once, play all tracks randomly. Press RDM once again, exit from random playback.
Track/Folder Navigation
– Press the -10/+10 buttons to jump 10 tracks backward or forward.
It is required that over 10 tracks be available on the storage medium.
– Press and hold the -10/+10 button to select the previous or the next folder. (If there are folders on the storage medium.)
Select the track or file for playback in MP3 format**
a) Press and hold the button to enter track search mode.
First “TRK0000“ will appear on the display.
b) Rotate the volume knob to select the number of your favorite track with high speed.
c) When the desired track number appears, confirm your selection by pressing SEL button.
If no any operation in 5 seconds,it will play the current track.

Auxiliarly Operation

Using this socket, it is possible to hear the sound of other playback devices such as MP3 players, CD players etc. through the car loudspeaker.

1. Please connect the external device with a 3.5 mm stereo jack plug to the AUX socket.
2.  Press the SRC button repeatedly until “AUX IN” appears in the display.
3. You hear the playback from the external device via the loudspeakers.

You can adjust the volume of the external device to a comfortable level with the volume control of this device.

Bluetooth Operation

Pair and Connect
Pair the mobile phone with the device before using it.

1. In any mode, prior to pairing and connecting, the BT logo in the LCD indicating that no device is connected. To begin pairing, enable BT mode on your mobile phone.
2. When the phone finds the car audio system, the “BOSS AUDIO 609UAB” name will be displayed.
3. Choose the “BOSS AUDIO 609UAB” from the device list to pair and connect with the car audio system. Upon confirming, the BT logo will stop flashing.
4. When pairing is complete, the mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the mobile phone plays music.

Make a Call
To make a call, dial the call directly from the paired mobile phone.
Redial Last Dialed Number
Press and hold the button on the control panel to redial the last dialed
phone number.
Answer a Call

• When the mobile phone is called, the incoming telephone number displays on the LCD.
• To receive the call, press the button on the front panel or button on the remote control.

Reject or End a Call
To reject or end the call, the button on the front panel or button on the remote control.

Bluetooth Operation

Switch Audio Between Car Audio and mobile Phone
During a call, press the VOL knob/button to switch the audio source from the car audio system back to your mobile phone.
Adjust Call Volume
During a call, use the VOL knob to adjust the call volume level.
Audio Streaming (A2DP)
The unit supports A2DP (advanced audio distribution profile) wireless streaming audio from your Bluetooth mobile device directly to your head unit. You can also control your music from the front panel of the head unit using AVRCP (audio video remote control profile).

1. After pairing, connecting and enabling streaming audio from a compatible mobile device, press the SRC button to enter BT mode and the “BT AUDIO” will be shown on the LCD display.
2. When a mobile device is paired, music played through that device will automatically be heard through the car audio system.
3. Press the or button to play the next or previous on the mobile phone.
4. Press the **** button to pause or resume music playback.

Push-To-Talk
This Push-To-Talk feature allows direct access to Android and IOS smartphone’s voice assistant capability when user establishes the Bluetooth connection between user’s smartphone and this receiver. Simply connect directly from this receiver via Bluetooth with the button.

Note:
Before using the Push-To-Talk, the user must enable the mobile data on the user’s smartphone.
To use the navigation feature, switch to the BT Audio source to hear voice commands over your vehicle’s speakers.

Remote Control

1. (Power on/off) button
2. VOL+/VOL-(volume increase/decrease) button
3. Band button, (answer call) button
4. PREV: tune down, seek down; Track down, fast reverse
5. SEL(selection) button
6. NEXT: tune up, seek up; Track up, fast forward
7.  Mute button, DEL(Delete) button
8. CLK(clock setting) button, (end call) button
9. **** button, preset station 1 button, keypad 1
10.  INT(intro) button, preset station 2 button, keypad 2
11.  RPT(repeat) button, preset station 3 button, keypad 3
12. RDM(random), preset station 4 button, keypad 4
13.  -10(previous 10 tracks), preset station 5 button, keypad 5
14.  +10(next 10 tracks), preset station 6 button, keypad 6
15.  ST(stereo) button, keypad 7
16.  LOUD(loudness) button, keypad 8
17. AMS(automatic music search) button, keypad 9
18. SRC(Source) button, keypad *
19. EQ(Equalizer) button, keypad 0
20. LOC(local)/DX button, keypad #

Note: When using the remote control for the first time, you must pull out the protective plastic tab from the battery compartment found on the back of the remote control.

Specifications

General
Power supply requirement : DC 12V
Maximum power output: 50W X 4CH
Speaker impedance: 4 – 8 Ohm
Unit Dimensions(WxHxD) : 7.0 X 2.0 X 2.76 inches
Weight: 1.04 lbs
Fuse: 10 A
RADIO
FM
Frequency Range: 87.5 MHz – 107.9 MHz (USA) 87.5 MHz – 108.0MHz (EUROPE)
Channel step: 200 KHz(USA) 50 KHz(EUROPE)
AM
Frequency Range: 530 KHz – 1710 KHz (USA) 522-1620 KHz(EUROPE)
Channel step: 10 KHz(USA) 9 KHz(EUROPE)
USB
Usable Audio Formats: MP3/WMA
USB Port Type: 2.0
USB Charging: 5V/1A
Pre-amp Output: Front and Rear
Frequency Response: 20 Hz – 20KHz
S/N Ratio: 60dB
BT
BT Profile supports: Headset, Handsfree and A2DP & AVRCP
Range of frequency: 2.4GHz

BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/support

0620
*iPod° and iPhone° are trademarks of Apple, Inc. registered in the U.S. and other countries. BOSS Audio Systems is not affiliated with Apple, Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BOSS Audio Systems is under license.
Other trademarks and trade names are those of their respective owners.**

Documents / Resources

| BOSS AUDIO 609UAB 200W Bluetooth Single Din MP3 Compatible Digital Media AM or FM Receiver [pdf] User Manual
609UAB, 200W Bluetooth Single Din MP3 Compatible Digital Media AM or FM Receiver, 609UAB 200W Bluetooth Single Din MP3 Compatible Digital Media AM or FM Receiver
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>