Waterdrop PT-04 Pitcher Filtration System User Manual

: June 5, 2024
: Waterdrop

Table of Contents

What’s included in the system
Care and safety information
Getting started / Instruction for use
Change water filter
Change smart indicator
Correctly dispose of Waterdrop smart indicator
Technical specifications
Questions & answers
3 months quality assurance
Performance Data Sheet
Contact us
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Waterdrop PT-04 Pitcher Filtration System User Manual

What’s included in the system

Care and safety information

Use cold water only. The operating temperature of this pitcher filtration system is 41-100°F/ 5-38°C.
Do not use with water that is micro biologically unsafe, or of unknown quality. This filter cannot filter other liquids other than tap water.
We recommend that you store your system in the refrigerator or in a cool area that is not in direct sunlight to get refreshing, great-tasting water.
If the filter dries out, soak it in cold tap water for 10 minutes to remove bubbles before use to activate the filter and ensure the best filtration performance.
If there is a lot of turbidity in tap water (such as cleaning the water tank or not using tap water for a long time), please flush it for a few minutes until the water turns clean before using.
If water filter pitcher is not going to be used in a long time, please put it in a clean container with lid. Then place it in the refrigerator which will prolong the cartridge life.
The filter must be protected from freezing, otherwise it might cause cracking and water leakage from the filter.

Getting started / Instruction for use

Step 1. Wash your hands, then remove filter from filter box.
Step 2. Please soak it in cold tap water for 10 minutes to remove bubbles before use to activate the filter and ensure the best filtration performance. (Figure 1.1)

Step 3. Hand-wash pitcher, lid and reservoir with a mild detergent. Don’t put it in the dishwasher. Do not use abrasive cleaners rinse thoroughly with water.
Step 4. Install filter into reservoir. Press firmly to ensure a tight seal. [Figure 1.2] Figure 1.2

Step 5. Fill the reservoir with cold tap water. Discard the first two times filtered water.

Step 6. Press the button for 3 seconds until the blue light flashes to activate the indicator. [Figure 1.3] Note: Repeat this step after each new filter replacement.

Status	Indication light	Remaining
Good	Blue stay on for 5 seconds	90 days

Replace soon

| Red flash a times| 10 days
Replace now| Red stay on for 5 seconds| 0 day

When you have filtered 200 gallons of water or the smart indicator red light is on, whichever comes first, you should change your filter.

Change water filter

Water filter replacement consult steps 1 to 6

Change smart indicator

The filter smart indicator is replace-able. Replace it by squeezing the clamping jaw. Figure 1.4

During the re installation, make sure that the clamping jaw is inserted into the groove completely.

Correctly dispose of Waterdrop smart indicator

If the battery expires, dispose the indicator according to all applicable provision and regulation.

Technical specifications

Filter capacity: 200 gallons (757 liters) / 3 months
Weight: 1.84 lbs (0.8 kg)
Size: 9.6 x 4.1 x 10.0 inches
Flow rate: 0.2-0.5 gpm / 0.8-2 Ipm
Temperature: 41-100 F / 5-38C

Questions & answers

Q: Why is water running slowly?

A : The filter cartridge may be clogged. Please check the indicator to see if its time to change the filter cartridge. If yes, please replace the filter cartridge immediately. If not, take out the filter and shake it intensely in order to shift the granules inside, which will improve the speed of water flow.

Q: Why does the water taste bad?

A : The product is unclean, or the filter cartridge is not installed properly. It could also be time to change the filter cartridge. Please clean the pitcher and install the cartridge correctly or replace the filter cartridge.

Q: My filter indicator is not working, I cannot see the color of the indicator!

A : The battery might be out of power. Do not worry, the filter indicator is replaceable. If in the warranty period, we can replace it for free.

Q: Why is TDS value not lowered after filtration?

A : TDS stands for total dissolved solids. It is composed of inorganic salts and a small amount of organic matter. This filter cannot lower the TDS value because it can remove harmful substances while keeping beneficial trace elements such as potassium, sodium, magnesium, and calcium, which can increase the TDS value. Please choose our RO system if you are looking for physical removal of TDS.

3 months quality assurance

We promise your water filter system for 3 months from the date of purchase (except for the filter cartridge which is assured for 30 days) against all defects in materials and workmanship, when used in compliance with the owner’s manual.

If the product proves to be defective within 3 months from the date of purchase, please contact our customer service. During the quality assurance period, we will replace or repair any part which is deemed to be defective, if product has not been subjected to tampering, alteration or improper use after delivery, and has not been repaired by the manufacturer.

The product is not promised against misuse, use in abnormal operation temperature conditions, conditions outside listed operating parameter or use in commercial operations.

We are not responsible for damage in transit and claims for such damage should be presented to the carrier by the customer.

If you have any further questions, please call customer service for free 1-888-352-3558, Monday to Friday from 8:00 AM-5:00 PM (PST). Our professional customer service team will take care of your problem in a timely manner.

Performance Data Sheet

System Model No : ECF-7015XX-21FZ

Substance reduction

The system has been tested and certified by the NSF International according to NSF/ANSI Standard 42 and NSF/ANSI Standards 372. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for the water leaving the system, as specified by NSF/ANSI Standard 42. While testing was performed under standard laboratory conditions, actual performance may vary.

Performance Data Sheet

System to be used with municipal or well water sources treated and tested on regular basis to ensure bacteriological safe quality. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Testing was performed under standard laboratory conditions, actual performance may vary.

Tested and certified by NDF International against NDF/ANSI Standard 42 in model ECF -7015XX-21FZ for the reduction of the claims specified on the performance Data Sheet, and to NSF/ANSI 372 (< 0.25% lead).