Chroma-Q 632-XXXX Blind Ceiling Mount User Guide
- June 5, 2024
- Chroma-Q
Table of Contents
Chroma-Q 632-XXXX Blind Ceiling Mount
For a full product manual please visit
www.chroma-q.com Part Number: CH632-9120,
CH632-9121
Model: 632-9120, 632-9121
For use with
Part Number: CHINHL[xxxx] Model: 632-XXXX
Installation Disclaimer
- Installation should be carried out by an experienced professional. The instructions below are provided for information only.
- All work should be verified to meet Local and National Building Regulations, and Health and Safety Standards in particular.
- Ensure that the specified torque is applied to fasten the Trim Ring and Angle Supports.
- The Angle Supports of the InspireTM fixture must be fastened to the ceiling with the appropriate load capacity.
- The use of a safety rated chain or other arrest cable is mandatory as per standard rigging practice.
- The brackets provided in the kit are for centering and supporting the trim ring. The weight of the fixture must be supported separately from the brackets provided in the kit
Kit Contents
Items | Part Number | Quantity |
---|---|---|
Trim Ring Blind Mount | 632-9005 / 632-9006 | 1 |
Bracket Blind Mount Clamp | 632-9001 | 3 |
Flag Blind Mount Clamp | 632-9002 | 3 |
Screw M5X0.8 PH 80mm | 450-1280-1 | 3 |
Push Nut M5 Thickness 1mm | 450-3401 | 3 |
Bracket Trim Ring Mount | 632-9004 | 1 |
Bracket Hook | 632-0012 | 4 |
Screw M5X12 PH Plps Blk | 450-1212-0 | 7 |
Washer Flat M5 Zn 20mm OD | 450-2420-1 | 4 |
Ceiling Blind Mount Install Guide | 632-0721 | 1 |
For the ease of installation most items of the kit have been partially assembled. They are
S/A | Description | Qty | Picture |
---|
A
|
Bracket Trim Ring Sub-assembly
|
1
|
B
|
Bracket Clamp Sub-assembly
(Note: Factory default for the Sub-assembly B uses Top and Middle Hole, User can change it to Middle and Bottom hole)
|
3
|
Tools Required
- Screwdriver with PH#1 (Minimum torque: 5.5 in-lb.)
Installation Guide
Hole Sizing Reference (inches/cm) Note:
- Ceiling hole size: 8.5” / 21.5 cm
- Trim Ring outer diameter: 12” / 30.5 cm
- Trim Ring inner diameter: 4” / 10 cm
Approvals & Disclaimer
The information contained herein is offered in good faith and is believed to
be accurate. However, because conditions and methods of use of our products
are beyond our control, this information should not be used in substitution
for customer’s tests to ensure that Chroma-Q® products are safe, effective,
and fully satisfactory for the intended end use. Suggestions of use shall not
be taken as inducements to infringe any patent. Chroma-Q® sole warranty is
that the product will meet the Chroma-Q® sales specifications in effect at the
time of shipment. Your exclusive remedy for breach of such warranty is limited
to refund of purchase price or replacement of any product shown to be other
than as warranted.
Chroma-Q® reserves the right to change or make alteration to devices and their
functionality without notice due to on-going research and development.
The Chroma-Q® InspireTM has been designed specifically for the lighting
industry. Regular maintenance should be performed to ensure that the products
perform well in the entertainment environment.
If you experience any difficulties with any Chroma-Q® products please contact
your selling dealer. If your selling dealer is unable to help, please contact
support@chroma-q.com. If the selling dealer is unable to satisfy your
servicing needs, please contact the following for full factory service:
Outside North America: Tel: +44 (0)1494 446000
Fax: +44 (0)1494 461024
| North America: Tel: +1 416-255-9494
Fax: +1 416-255-3514
---|---
For further information please visit the Chroma-Q® website at www.chroma-q.com.
Chroma-Q® is a trademark, for more information on this visit
www.chroma-q.com/trademarks.|
---|---
The rights and ownership of all trademarks are recognized
References
- Home | Chroma Q | Award-Winning LED Lighting
- Home | Chroma Q | Award-Winning LED Lighting
- Chroma-Q | Trademarks and Copyrights
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>