OCTO OP-2 Pulse Wave Pump Instruction Manual

: June 3, 2024
: OCTO

Table of Contents

OCTO OP-2 Pulse Wave Pump
Overview
Installation
Trouble Shooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OCTO OP-2 Pulse Wave Pump

Dear Customer
Thank you for choosing OCTO, a quality product manufactured by HONYA CO., LTD. In order for you to safely use our product for maximum results, please read the instruction prior to use. We would strongly suggest that you retain this Instruction for future reference.

Safety on Magnet

CAUTION -Extremely Strong Magnets, please handle with care.
Keep magnets out of reach of children.
Do not snap both magnets together directly.
Keep the magnets away from electronics products and magnetic storage devices such as credit cards, pacemaker etc.

Notes

Never handle any electrical component when your hands are wet.
Ensure that all components (power adapter, controller, wires, etc) are properly set -up to prevent accidental damage.
For indoor use ONLY.
For controller operation, please refer to the instructions as per this manual.
Keep controller cool and dry, do not expose to direct sunlight or heat.
Pump Protection System – if pump is detected to be running dry, it will stop operating after about a minute. To restart the pump, off the power, re-position the pump to ensure that it is submerge in the water then turn on the power.
Should in the unlikely event that your pump stop working, please refer to the trouble shooting page in this manual.
Please maintain your pump as per this manual.

Overview

Introducing our new OCTO Series Direct Current (DC) Wave Pump, OCTO Pulse features Multiple Angles Adjustment, a new WiFi Controller, APP Control and couple with a 0-1 0V Port, 4 programmable wave patterns, high quality ceramic shaft and bearing to reduce wear and tear, and the latest variable speeds flow technology for refined control, enhanced performance, energy-efficiency and safer operations.
Our New WiFi enable controller can now power *Two Wave Pumps simultaneously and settings between these two wave pumps easily via our bespoke OCTO APP available for both IOS or Android devices.

Features & Benefits

360° Range of Adjustment
Low-profile magnetic mount
Neodymium magnets
WiFi enable
App controllable
Compact and durable
Silent Operation
4 pre-programmed flow patterns
Dual feed mode (15 or 60 mins)
Single Controller to control and power 2 wave pumps*

Flow Rate Charts

Step

|

Power

w

| OP-2+

Flow

LPH

|

Rate

GPH

| Step Power| OP-4+

Flow

LPH

|

Rate

GPH

---|---|---|---|---|---|---
+30%| 5.0| 3200| 845| +30% 11| 5360| 1410
+40%| 6.0| 3800| 1000| +40%          14| 7900| 2080
+50%| 6.5| 4050| 1070| +50% 17| 9600| 2530
+60%| 7.0| 4450| 1170| +60%          20| 11300| 2980
+70%| | 4720| 1250| +70%          22| 12400| 3270
+80%| 8.5| 5100| 1350| +80%          25| 14100| 3720
+90%| 9.5| 5820| 1540| +90%          28| 15900| 4200
+100%| 10.0| 6000| 1585| +100%         32| 17000| 4490

Package

Please check the content in the package

Attention:

DC24V/1.0A (AC/DC Adapter) for OP2 / OP2+OP2
DC24V/2.5A (AC/DC Adapter) for OP4 / OP4+OP2
DC24V/4.0A (AC/DC Adapter) for OP4 / OP4+OP4

Installation

Slide the Inner and Outer Magnet into your desired position (image 1/2). DO NOT Snap both Magnets together.
Mount the Pump to the Inner Magnet, ensuring that the power cable is on top (image 3/4).
Tie the cord to the Cable Management Plate using a Cable Tie. Do not tighten the Cable Tie till confirmation of Pump Position. Ensure to have some allowance for final adjustment of pump position before cutting off the excess Cable Tie.
Adjust angles according to your requirements (image 7/8).
Connections as per below diagram. OCTO Pulse system has a built-in safety mechanism. Make sure all cables are connected (1 and 2), mount the controller before turning on the power (3)
Attention : Before starting the pump, please ensure that livestock are not near the pump.

Controller Quick Start Guide

• Legend

0-10V Input (3.5mm TRS Audio port)
Power supply Connection
- (DC24V) DC24V/1.0A: OP2 / OP2+OP2
- DC24V/2.5A: OP4 / OP4+OP2
- DC24V/4.0A: OP4 / OP4+OP4
Connection for OCTO Wave Pump
Connection for OCTO Wave Pump
LED Display screen
SETTING
Power I Pause
Power : once controller is connected; it is automatically ON. Press ( ) and HOLD for 3 seconds to power OFF.
Pause : press ( ) once to go into Pause Mode: Press ( ) or ( ) to select 15 mins or 60 mins, press ( ) to set the timing.
Settings / WiFi ON-OFF
Press ( ) once to go into settings, depress again to return to the previous menu WiFi ON / OFF Switch: Press ( ) and HOLD for 3 seconds, will appear on screen to indicate WiFi function is turn ON.
Attention : when WiFi function is turn ON, you can only access ON-OFF/ Pause/ WiFi ON-OFF / WiFi Network/ Pump Selection functions/ Factory Reset. All other buttons will be disabled and you can only do the settings of the pump via APP only.
Depress ( ) or ( ) to enter settings for wave patterns/wave patterns flow rate I wave patterns timing and adjust pause duration. Press ( ) to switch/ comfirm the selection.

Network and Factory Reset
Pump selection: simultaneously depress ( ) and ( ) and HOLD for 3 seconds. Network selection: when WiFi is turn ON, simultaneously depress( for 3 seconds to select network. will start blinking. ) or (

Factory Reset: Simultaneously depress ( ) and ( ) for 3 seconds.

Attention:

When 0-1 0V port is use, Controller will only let you access ON-OFF / PAUSE functions only.
When WiFi function is turn ON, you can only access ON-OFF/ Pause/ WiFi ON-OFF/ WiFi Network/ Pump Selection functions/ Factory Reset. All other buttons will be disable and you can only do the settings of the pump via APP only.
Display will go into sleep mode when inactive for 3 minutes. Press any button to revive.

0-1OV Wiring diagram:

SCREEN ICON

MODELS

WAVE MODE FLOW PATTERNS

DISMANTLING AND MAINTENANCE