Xiaomi TiinlabTiinlab User Manual

: June 5, 2024
: Xiaomi

Table of Contents

Product Overview
Instructions
Connecting
Function Overview
Specifications
WEEE Information
Safety Caution
WARRANTY NOTICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Mi True Wireless Earphones 2 Basic User Manual ·01

Read this manual carefully before use, and retain it for future reference.

Product Overview

Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

Instructions

Charging

Charging the earphones
When the earphones are placed in the charging case, they will automatically start charging.
Charging the charging case The indicator of the charging case is white during charging, and goes off once it is fully charged.

Checking Battery Level

Checking the battery level of the earphones After connecting the earphones to a phone, you can check the earphones’ battery level on the phone’s status bar.
Note: The phone’s status bar always displays the battery level of the earphone with the lowest battery level. This feature is not supported by some phones.
Checking the battery level of the charging case Open the lid of the charging case, or place the earphones into the charging case:
1. When the indicator light of the charging case stays lit for 5 seconds, it means the battery is sufficient.
2. The indicator of the charging case is blinking white, which indicates that the battery level of the charging case is low. Please charge it immediately.
Checking the battery level by a Mi phone
After successfully connecting to a phone, place the earphones into the charging case and close its lid. Make sure the Bluetooth function is enabled on your Mi phone. Hold your phone close to the charging case, then open the case’s lid. A notification will appear on the phone, then you can check the battery level of the earphones and the charging case.

Note: When checking the battery level on your phone, please update your Mi phone to the latest stable version. This feature is currently only supported by some Mi phones.

Turning On
When opening the charging case, the earphones will automatically turn on.
Note: When using the earphones for the first time, place them in the charging case and close the lid to activate them.

Sleep Mode
Place the earphones back into the charging case and close the lid, the earphones will disconnect and go into sleep mode automatically.

Wearing
Take the earphones out of the charging case, and insert them into your ears according to the le (L) and right (R) marks.
Note: Atter using the earphones, place them back into the charging case. This will extend their lifespan and help you avoid losing or misplacing them.

Connecting

Connecting the earphones to a new device

Place the earphones into the charging case, press, and hold the
touch area of either earphone for 3 seconds. The indicator of the earphones is blinking white, and the earphones are waiting for a connection.
Enable the device’s Bluetooth, then locate and connect to “Mi TW Earphones 2 Basic”. If a passcode is requested, enter “0000”.

Connecting the earphones with a Mi phone Place the earphones into the charging case and close its lid. Make sure the Bluetooth function is enabled on your Mi phone. Hold your phone close to the charging case, then open the case’s lid. Follow the on-screen instructions of the phone to connect to the earphones.
Note: The feature of fast connection is currently only supported by some Mi phones, please update your Mi phone to the latest stable version.
Connection interrupted When your device is out of wireless range of the earphones or its Bluetooth function is disabled, the earphones will automatically enter the awaiting connection mode. If the earphones are not connected to any device within five minutes, they will enter sleep mode.
Automatic connection When the earphones are in the charging case, opening the lid of the charging case will automatically connect the earphones to the most recently used Bluetooth device. If the earphones are not connected to any device within five minutes, they will enter sleep mode.
Note: If the earphones cannot automatically connect to a device, you will need to manually connect the earphones to the desired device via the device’s Bluetooth settings.
Due to the connection characteristics of the Bluetooth signal, in dense environments with 2.4 GHz electromagnetic signal interferences, there may be occasional disconnects or no sound.

Clearing connection history

Place the le and the right earphone into the charging case.
Simultaneously press and hold the touch areas of the le and the right earphones for seven seconds, then release the touch areas once the indicators of the earphones light up in white.
The earphones have been reset and the connection history has been cleared. The indicators of the earphones blink white, and the earphones are waiting for a connection.

Function Overview

| ● Incoming calls
Gently tap either one of the earphones twice: Answer/End calls● Music and voice assistant
While wearing both earphones: Gently tap the right (R) earphone twice: Play/Pause music Gently tap the left (L) earphone twice: Access the voice assistant Taking out an earphone: Pause music
While wearing one earphone: Gently tap the earphone twice:
Play/Pause music
---|---

Notes:

The voice assistant function can be used only if your device supports it, and this function needs to be granted permission on the device.
When only using the le earphone, place the right earphone into the charging case and close the lid.

Specifications

Model: TWSEJ08WM
Net Weight: 48 g
Input: 5 V 1 A
Charging Port: Type-C
Impedance: 32 Ω
Charging Time: Approx.1.5h
Wireless Connectivity: Bluetooth 5.0
Bluetooth Profiles: BLE/HFP/HSP/A2DP/AVRCP
Supported Audio Codecs: SBC/AAC
Wireless Range: 10 m (open space without obstacles)
Earphones’ Battery Life (standalone): Approx. 5 h
Total Battery Life (with charging case): Approx. 20 h
Bluetooth Operation Frequency: 24022480 MHz (for EU)
Maximum Transmit Power for BT: 10 dBm (for EU)
Maximum Transmit Power for BLE: 10 dBm (for EU)

WEEE Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
Hereby, Tiinlab declares that the radio equipment type TWSEJ08WM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html

Safety Caution

Do not expose batteries or battery packs to excessive heat such as sunshine, fire, or the like.
Replacement of a battery with an incorrect type that can defeat a safeguard (such as catching fire, explosion, leakage of corrosive electrolyte, etc).
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used ba eries according to the instructions.
The product operation maximum ambient temperature is 40°C.

To prevent possible hearing damage, do not listen at high volume levels for long periods.
The symbol indicates DC voltage

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device is too small to bear the label information, and we list the label contents on package and user manual as well.
The marking information is located at the bottom of apparatus.
FCC ID : 2ASDITWSEJ08WM
IC24662-TWSEJ08WM
HVINV7
CAN ICES-3(B)/NMB-3(B)

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their respective owners.

Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Tiinlab Acoustic Technology Limited (a Mi Ecosystem company)
Address: Tianliao Building 1403, Tianliao Industrial Area A, Taoyuan Street, Nanshan District, Shenzhen 518055, China
For further information, please go to www.mi.com

WARRANTY NOTICE

As a Xiaomi consumer, you beneﬁt under certain conditions from additional warranties. Xiaomi oﬀers speciﬁc consumer warranty beneﬁts which are in addition to, and not instead of, any legal warranties provided by your national consumer law. The duration and conditions related to the legal warranties are provided by respective local laws. For more information about the consumer warranty beneﬁts, please refer to Xiaomi’s oﬃcial website https://www.mi.com/en/service/warranty/. Except as prohibited by laws or otherwise promised by Xiaomi, the after-sales services shall be limited to the country or region of the original purchase. Under the consumer warranty, to the fullest extent permitted by law, Xiaomi will, at its discretion, repair, replace or refund your product. Normal wear and tear, force majeure, abuse, or damage caused by the user’s negligence or fault are not warranted. The contact person for the after-sale service may be any person in Xiaomi’s authorized service network, Xiaomi’s authorized distributors, or the ﬁnal vendor who sold the products to you. If in doubt please contact the relevant person as Xiaomi may identify.
The present warranties do not apply in Hong Kong and Taiwan. Products which were not duly imported and/or were not duly manufactured by Xiaomi and/or were not duly acquired from Xiaomi or a Xiaomi’s oﬃcial seller are not covered by the present warranties. As per applicable law you may beneﬁt from warranties from the non-oﬃcial retailer who sold the product. Therefore, Xiaomi invites you to contact the retailer from whom you purchased the product.