HALNY HL4GQVS COMPACT PREMIUM GPON ONT WIFI MESH Installation Guide
- June 5, 2024
- HALNY
Table of Contents
HALNY HL4GQVS COMPACT PREMIUM GPON ONT WIFI MESH
Safety Guidance
Safety Check
Before installing the device. you must check the following items
Electric Safety
- Ensure that there are no inflammable, conductive or moist objects around. Check whether the cables are aged and whether other electrical appliances are placed stably
- Check whether the alternating or direct input current is within the allowed range of the device. whether the polarity of the direct current is correct, and whether the earth line is properly connected
Device Position
- Because the running electric device easily generates heat. please ensure to place the device in a well-ventilated environment,
- Avoid direct sunshine, and do not place the device on a PC case
- Keep the device away from heat and water
- Check whether the power supply is available. The input voltage fluctuationrange must be smaller than 10%. The power plug should not share one socket with a hair drier, an iron, or a refrigerator.
Safety Caution
- Read the quick installation guide carefully before using the device,
- Note all Cautions in the quick installation guide
- Do not use any accessory that does not belong to the device without the prior consent of the manufacturer, as it may cause fire or product damage.
- Use the power adapter accompanied in the package
- Do not place any object on the device
- Keep the device dry, ventilated, rainproof, and clean
- During lightning weather, unplug the power plug and all connection cables, to protect the device against lightning.
- Clean the device using a soft and dry cloth rather than liquid or atomizers. Power off the device before cleaning it
- Power off the idle device
- Keep the ventilation hole clean and prevent any object from dropping into the device through it. Otherwise. it may cause a short circuit and further cause device damage or fire. Do not spray liquid on the surface of the device.
- Do not open the case of the device. especially during device power-on,
- Before plugging or unplugging the power, ensure that the power is off, thus avoiding a surge.
- Be careful when unplugging the power, as the transformer may be very hot
- Cover the optical interface with a fiber interface cap when it is not in use. Avoid direct eye exposure to the laser emitted from the optical interface. Wear safety glasses if possible, to protect your eyes.
Caution:
Please read the above safety guidelines carefully before device use. Users
should assume responsibilities in compliance with the above instructions for
any accidents due to
Overview
This chapter mainly describes the functions and the structure of the HALNy
HL4GQVS
Features and Function
- Fast rate. Support up to 1.25Cbps uplink and 2.5Gbps downlink data transmission rates,
- Strong maintainability. Provide various statuses of LED indicators, to help troubleshoot
- Long transmission distance, up to 20 km.
Front and rear panel
The description of the front and rear panel of the GPON ONU as follows.
Front Panel
Rear Panel
ONU Rear Panel Description
ONU Installation
The chapter describes the required installation operations before you use the
device for the first time.
Product Networking Application FTTH
Fiber to the Home (FTTH) means installing the ONU in residences or enterprise
buildings. The optical line terminal (OLT) is placed in the central equipment
room The ONU can be placed in the home of a user. or it can provide a
connection for the user through the Ethernet interface, according to the user
requirement. The OLT connects to the ONU with an optical distributor in the
point-to-multipoint was. See the following figure.
Note: The ONU applies to installation at home or in the corridor. Because installation and cabling in the corridor are relatively complex, let the professional engineers deploy according to the actual situation. This manual describes the procedure for installing the device at home and is for reference only
Installation Preparations
The Ethernet interface of your computer connects to the Ethernet interface of
the ONU. Before installing it. ensure that an Ethernet adapter is already
installed in your computer
Connecting ONU
Connecting the Network Cable
Step 1: Use the one end of the network cable to connect the Ethernet
interface of the computer
Step 2: Use another end of a network cable to connect the Ethernet
interface on the rear panel of the HALNy HL 4GQVs
Connecting the Fiber
caution:
- When a fiber is not in use, ensure to cover the optical interface of the ONU and the dust cap of the optical fiber. Prevent grease. dust pollution or water immersion, which may lead to unavailable fiber and optical interface of the device.
- If fibers need to be fixed or bended during cabling, do not fasten the fibers too tight. Avoid fiber extrusion, which may lead to an increase of fiber material or unavailable fiber.
Connecting the Power Adapter and Power Cord
- Connect the output end of the power adapter included in the device package to the input end of the power supply of the ONU
- Insert one end of the power cord attached to the device into the input end of the power adapter. Insert the other end of the power cord into the power Socket
- Check whether the Power indicator is on. If it is on. the power supply is normal. Otherwise, check whether the power cord and the power adapter are correctly connected.
Troubleshooting
Technical Specification
Appendix A Acronyms and Abbreviations
Additional information
Declaration of Conformity (CE)
This device has been tested and found to comply with the stated standards
which are required by the Council Directive of 2014/30/EU. The device complies
with this CE Declaration when the installation is done in accordance with the
instructions documentation. The importer don’t take responsibility for any
issues caused by improper use of the device. The full document is on below web
page and it is available in importer CE /warranty terms and conditions:
www.halnv.com Importer FIBRAIN Sp. z o.0
36-062Zaczernie 19OF (POLAND) info@fibrainpl
Information furnished by HALNy Networks is believed to be accurate and reliable. However, no responsibility is assumed by the importer for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of the manufacturer. The manufacturer reserves the right to change specifications at any time without notice.
Recycling
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled according to European directive 2012/19/in order to be recycled or dismantled. This will minimize the negative effects on the environment and human health resulting from the possibility of the presence in and the equipment substances. mixtures of hazardous components. A user can give the product to a competent recycling organization, to WEEE collection points or to a distributor(in accordance with local regulations).
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
The equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>