Puro Sound Labs PUROPQ2020 PuroQuiet Active Noise Cancelling Headphones User Guide

Puro Sound Labs PUROPQ2020 PuroQuiet Active Noise Cancelling Headphones

Specification

• Type of headphone: Active Noise Cancelling On-ear
• Volume limiting: 85 dBA sound Limit
• Ambient noise reduction: 78% of noise isolation
• Wireless: Bluetooth@ 5.0 wireless headphones
• Wireless range: Up to 32 feet from Bluetooth® source
• Battery life: 23 Hours w/ ANC ON & 35 Hours w/ ANC OFF
• Battery type: Lithium ion rechargeable
• Drivers: 40 mm custom dynamic drivers
• Dynamic range: 20Hz 20kHz with <1% total harmonic distortion

1. Bluetooth Button
2. Power On/Off Switch
3. Vol+
4. Vol-
5. Built-in Microphone
6. Headband
7. Ear Cushion
8. Earcup
9. ANC On/off Switch
10. ANC indicator
11. 3.5mm audio port

Quick Start (Pairing)

1. Charge the headphone until the blue light remains on (indicating full charge). This is accomplished by plugging the headphone into the charging cable, the charging cable into the USB wall charger and connecting the USB wall charger to an AC outlet. (Charging may take up to 3 hours.) RED LED=Charging 8& BLUE LED = Fully Charged
2. Turn the Headphone on and enter “pairing mode. For the first paring, the headphone LED will fast flash BLUE and say “power on” & “pairing”, indicating that it is ready to pair. For subsequent product pairing. (the headphone will need to be turned on and) the Bluetooth button will need to be held for 3 seconds to enter “pairing” mode.
3. Bring the source device within 1 meter of the headphone. Follow the source device instructions to look for discoverable devices. Select “PuroGuiets” from the list You will hear “connected” when pairing is complete and the LED will change from a fast flashing blue to a slow flash blue. The headset is ready for music or phone use. BLUE fast LED flash in pairing mode & BLUE slow LED flash paired

Wired Use

When using the Puro 3.5 limiter audio cable, make sure you insert the correct side into your headphones, there is a direction arrow on the black cable showing which side g0es into the headphones When going back to the Bluetooth connection, be sure to unplug the limiter cable. Note: when using the limiter audio cable, be sure to keep the headphones powered OFF as that can cause the audio to be low or not work as the power button is only for Bluetooth use.

Music Use

1. Choose media to playback and adjust the volume to your desired level.
2. Place the headset on your (or your child’s head), the size can be adjusted by pulling the “arms” down or pushing them back into the “headband”
3. The Bluetooth button can be used to pause and resume the playback of music.
4. The Vol and Vok buttons can be pressed or held to adjust the volume to the desired level.

Phone Use

Initiate calls on your mobile handset. Music playback will be paused for the duration of the call. A short press of the Bluetooth button will end the phone cal. For incoming calls, a tone will sound on the Bluetooth headset.

• A short press of the Bluetooth button will answer the call.
• A one-second press of the Bluetooth button will reject the call. Hold the Bluetooth button until a tone is heard, then release.
• A three-second press of the Bluetooth button will transfer the call back to the handset. Another three-second press, while the phone call is underway, will return the call to the headset.

Noise Cancelling Function

When you slide the ANC button to the “On” side, the green LED will light on, then you can enjoy the headphone in Noise cancellation mode. When you don’t need the Noise cancellation function, please slide the ANC button to the OFF side.

Daisy Chain Sharing

Perfect for connecting two headsets to share one device

1. Connect headphone A to the device either Bluetooth or with the Puro limiter audio cable.
2. Once headphone A is successfully connected. plug in the Daisy Chain cable (micro USB- MicroUSB cable) into headphone A followed by headphone B.
3. Power on headphone B if using a Bluetooth connection and begin playing the device being shared.

Safety Information

1. Continued exposure to loud noise (more than 85 decibels) (85 db) may cause gradual but permanent damage to hearing.
2. Do not use the headphones with products that can achieve levels above the “comfortable” guideline.
3. Do not use the headphones any time it would be dangerous to not be aware of noises around you.
4. If using while on an airplane, please follow the instructions of the crew for permitted use of a Bluetooth product.
5. Do not use or store the headphones in a wet environment. If the headphones are submerged or become wet, do not use them.

This device contains license-exempt transmitter(receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device

Guarantee & Warranty

Puro Sound Labs, LLC warrants the original owner of this product against manufacturing and material defects under normal use for a period of one (1) year from the date of retail purchase from Puro Sound Labs or a Puro Sound Labs authorized reseller. The warranty does not cover damages resulting from misuse, abuse, water damage, normal wear and tear, or modification. For any questions or warranty claims, please contact our support team!
Phone: -888-590-PURO (7876)
Email:support@purosound.com
Our office hours are 9-5 PST. Please leave a message if outside of this time and we will get back to you within 24 hours. Puro Sound Labs, at its sole discretion, will repair or replace the product, or refund the original owner the purchase price.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference wl not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

This devioe complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference recelved, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>