Chiyu Technology CSS-E-V15 Face Recognition Controller Installation Guide

June 5, 2024
Chiyu Technology

Chiyu Technology CSS-E-V15 Face Recognition Controller

Package content

  • Controller x 1,
  • wall hanger x 1,
  • user manual x 1,
  • screwdriver x 1,
  • kit pack x 1
  • Kit pack : screw x 4,
  • screw anchors x 4,
  • diode (1N4004) x 1
  • 4 pin cable x 1,
  • 8 pin cable x 1,
  • 9 pin cable x 1

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-2

Specifications

Dimension: 122.5 x 185 x 89(mm)

  • Power: 9 24 VDC/ 1A
  • Wiegand communication: Max to 100 meters
  • RS485 communication Max to 1000 meters
  • Face recognition distance: 50~ 100 cm
  • Install Wall: recommend installation height 115 125 cm

Installation instructions

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-3

Application structure

Terminal + WG reader can assign IN/ OUT mode

Terminal + BF-SO+ WG reader can assign IN/ OUT mode

(Terminal + CSS-AlO RELAY BOX)

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-6

(Terminal + CSS-All RELAY BOX)
Support POE power supply, only support single machine, door lock needs additional power supply

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-7

Terminal Front Description

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-8

Installation

115 153~190
117 155~195
119 157~200
121 159~205
123 161~210
125 153~215

The installation height is mainly for shorter person The face is aligned to the lower edge of the display frame

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-10

The installation height is mainly for shorter person Recognition distance is about so~10ocm Recommended installation height form the bottom of the machine to ground is about 11s~12scm Please bow your head slightly when recognizingto improve recognition success rate

installation environment

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-11

When installing outdoors, direct sunlight equipment, oblique sunlight equipment or direct sunlight equipment through window are prohibited When installing indoors, make sure that the place must be installed away from windows/ doors/ lamp more than 2 meters away equipment

Terminal Back Explanation

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-12

Cable diagram

Chiyu-Technology-CSS-E-V150-Face-Recognition-
Controller-13

Cable description

4PIN

485- GRAY For Relay Box BF-50
485+ BROWN
VIN RED DC 9~24v (lA)
GND BLACK

8 PIN

ALARM-NC YELLOW BLACK 10 Relay Bell Alarm/ Ring Relay
ALARM-NO WHITE BLACK
ALARM-COM GREEN BLACK
WG IND RED WHITE WG Input Connect

WG Reader

WG IN 1| BLACK WHITE
GND| BLACK| GND
LED| ORANGE| Control WG Reader LED/ Buzzer Action
BUZZER| PINK BLACK

9 PIN

D OOR-NC| YELLOW| ****

Door Relay

---|---|---
DOOR-NO| WHITE
DOOR-COM| GREEN
EXIT| VIOLET| Exit Button
SENSOR| BLUE| Door Sensor
FIRE| PINK| Fire Alarm
GND| BLACK| GND
WG OUT0| GRAY BLUE| WG Output
WG OUT 1| ORANGE BLACK

FCC Warning

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals