Kelung Technology Industrial KLXX000X WLAN IP Extender User Guide
- June 5, 2024
- Kelung Technology Industrial
Table of Contents
Kelung Technology Industrial KLXX000X WLAN IP Extender
Parts List
Receiver Group
Transmitted Group
No.| Parts number| Parts name/ Specification.| Qty|
Remark
---|---|---|---|---
1| F-CS-WIFIRX-001| 2.4G Receiver IP extender| 1|
2| F-CS-WIFIRX-002| 2.4G Receiver Antenna/
12dbi
| 1|
3| F-CS-WIFIRX-003| 2.4G Antenna Cable(3m)/
RP-SMA Male to N Type Male
| 1|
4| F-CS-WIFITX-001| 2.4G transmitted IP extender| 1|
5| F-CS-WIFITX-002| 2.4G Transmitted Antenna/
14dbi
| 1|
6| F-CS-WIFITX-003| 2.4G Antenna Cable(30 cm)/
RP-SMA Male to N Type Male
| 1|
7| NVR019| NVR 4CH/
4/8/16CH NVR
| 1|
8| F-CS-I13-D09-40-B4-1| IP Camera
Full HD 1080P
| 1| Infrared/
normal
9| Adapter014| POWER 2A AC in 110 ~ 230 V
Output DC 12 V / 2 A
| 2|
Transmitted Group
Installation guide
Wlan Infrastructure-1 in Elevators.
Wlan installation structure in Elevators.
The Procedure:
-
The IP camera installs inside of the elevator car and connect the DC power supply with the elevator car.
-
And install the TX IP Extender and the transmitting antenna are on the bottom of the elevator car; and install other DC power supply to the TX IP Extender. Then, Use the 30cm antenna cable connect the antenna and IP Extender.
-
Install and Connect the Cat.5e/ 6 cable with IP Camera and TX IP Extender.
-
The supplied L-shaped iron plate can be used and install at the bottom of the elevator car or to use the fixed-beam to fixed transmitting antenna can be changed, depend on varieties site environments. (The same fixed methods with receiving antenna.)
The each waterproof connector needs to be locked, the power supply, antenna,
and network RJ45 on the RX/ TX IP Extender.
Example
Wlan Installation Photo (The Building height under the 45 floors)
RECEIVER
Wlan Installation Photo (The Building higher than the 45 floors)
Receiver parts
The Receiver IP Extender setup configuration
- The receiver IP Extender box and receiving antenna are placed at the bottom of the elevator tunnel. The actual installation position is depends on the site environment.
- The antenna devices must not interfere with the original wire of the elevator.
- The transmitting antenna should be aligned with the receiving antenna, and should not deviate too far.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device must not cause harmful interference, and
2. This device must be able to withstand any interference received, including
interference that may cause undesired operation.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorienting or relocating the receiving antenna.
- Increasing the distance between the equipment and the receiver.
- Connecting the equipment to a different outlet from that to which the receiver is connected.
- Consulting the dealer or an experienced technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the
shielded signal cord supplied with this unit. The Federal Communications
Commission warns that changes or modifications to the unit not expressly
approved by the party responsible for compliance could invalidate the user’s
authority to operate the equipment.
FCC RF Radiation Exposure
This equipment complies with the FCC RF radiation exposure limits stipulated for an uncontrolled environment. This device and its antenna must not be co- located or operated in conjunction with any other antennas or transmitters. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed so as to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antennas or transmitters. Professional installation instruction
Installation personal
This product is designed for specific application and needs to be installed by
a qualified personal who has RF and related rule knowledge. The general user
shall not attempt to install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can
be kept 40cm from nearby person in normal operation condition to meet
regulatory RF exposure requirement.
External antenna
Use only the antennas which have been approved by the applicant. The non-
approved antenna(s) may produce unwanted spurious or excessive RF transmitting
power which may lead to the violation of FCC/IC limit and is prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>