Norpolifomor KS-SF33R Anti Theft Bike Tail Light Alarm User Manual

Norpolifomor KS-SF33R Anti Theft Bike Tail Light Alarm

Product Information

Specifications:

• Product Name: Anti-theft Bike Tail Light Alarm
• Model: KS-SF33R
• Battery: Built-in lithium battery
• Brake Light: Yes
• Tunnel Night Lights: Yes
• Taillight Modes: Multiple modes available
• Vehicle Locate Ringing: Yes
• Sound Level: 110 dB
• Sensitivity: 7 levels
• Charging Port: USB-C
• Waterproof: Yes
• Low Battery Indicator: Yes
• Dustproof: Yes

Product Usage Instructions

Product Instruction
The product consists of various components as described below:

• Red tail light
• Speaker
• 5V USB-C Port
• Two-part Bracket
• Silicone Pad
• Light mode button/pair button
• Bracket Base
• Zip Ties
• Arm Button
• Disarm Button
• Taillight on and mode button
• Vehicle locate ringing button
• WL03C(Optional)
• WL09C(Optional)

Bracket Installation:

1. Fix the anti-loosening nut first by aligning the round head of the nut with the rubber ring facing outward and the hexagonal side aligned with the groove.
2. Rotate the bracket into the back of the host until it locks, and then screw it on to fix it.
3. Place 2 silicone pads on the two-part bracket, aligning the contours on the silicone pad with the grooves on the inside of the brackets.
4. Place the two-part bracket with silicone pads on the selected tube and tighten the screw until the mount does not slide on the tube. Check the tightness periodically.
5. It is recommended to install the USB charging port face down for better waterproof effect.

Zip Ties Installation:

1. If the bracket diameter is not fit for your frame diameter, you can choose zip ties installation.
2. Rotate the other base into the bottom of the host and screw it in.
3. Fix it with zip ties by aligning and locking the screw hole.

Quick Installation Guide

Charge to Activate Before Use

• Please charge the product before use to activate it. It is recommended to fully charge it. Alternatively, you can press and hold the host button for 10 seconds to activate it.
• Note: Charge using the included USB cable and a 5V power adapter (not included in the package). Some fast charger plugs may not be compatible.

Bracket Installation
Bracket installation is suitable for bikes, electric bikes, tricycles, or any other tube-based vehicles.

1. Fix the anti-loosening nut first by aligning the round head of the nut with the rubber ring facing outward and the hexagonal side aligned with the groove.
2. Rotate the bracket into the back of the host until it locks, and then screw it on to fix it.
3. Place 2 silicone pads on the two-part bracket, aligning the contours on the silicone pad with the grooves on the inside of the brackets.
4. Place the two-part bracket with silicone pads on the selected tube and tighten the screw until the mount does not slide on the tube. Check the tightness periodically.
5. It is recommended to install the USB charging port face down for better waterproof effect.

Zip Ties Installation
You can choose zip ties installation if the bracket diameter is not fit for your frame diameter.

1. Rotate the other base into the bottom of the host and screw it in.
2. Fix it with zip ties by aligning and locking the screw hole.

Taillight Modes

• The product offers various taillight modes, including Slow Flashing mode and Breathing mode.
• In intelligent auto modes, the host taillight will light up for 30 seconds and then automatically detect the brightness of the riding environment. It will turn off when it is bright and turn on when it is dark. In a dim environment, if you stop for more than 30 seconds, it will automatically turn off to save power. If you start riding again, it will automatically light up.

FAQ

• Q: How do I activate the product?
  A: Please charge the product before use to activate it. Alternatively, you can press and hold the host button for 10 seconds to activate it.

• Q: Can I use a fast charger plug to charge the product?
  A: Some fast charger plugs may not be compatible. It is recommended to use the included USB cable and a 5V power adapter to charge the product.

• Q: How do I install the product using the bracket method?
  A: Follow the bracket installation steps provided in the user manual. Make sure to check the tightness of the screws periodically.

• Q: How do I install the product using the zip ties method?
  A: If the bracket diameter is not suitable for your frame diameter, you can choose zip ties installation. Follow the zip ties installation steps provided in the user manual.

• Q: What are the available taillight modes?
  A: The product offers various taillight modes, including Slow Flashing mode and Breathing mode. In intelligent auto modes, the taillight will automatically adjust based on the brightness of the riding environment.

Product Instruction

Host Diagram

1. Red tail light
2. Speaker
3. 5V USB-C Port
4. Two-part Bracket
5. Silicone Pad
6. Light mode button/pair button
7. Bracket Base
8. ZipTies

Quick Installation Guide

Charge to Activate Before Use
Please charge to activate before use, otherwise it may not work. And we recommend you fully charge. (Or press and hold the host button for 10 seconds to activate)
Note: Please charge with the package included original USB cable, and 5v power adapter (package NOT included), please know some fast charger plugs are not compatible.

Installation Method

1. Bracket installation is more suitable for bikes, electric bikes, tricycles, which is fixed on seat tube, head tube, rear backrest or any other tube。

2. Installation step:

3. Step1. Fix the anti-loosening nut first Installation diagram:
   Tip: The round head of the nut with the rubber ring is facing outward, and the hexagonal side is aligned with the groove. Then use a hard surface to push the nut into the hole of the bracket forcefully.

4. Step2. Rotate bracket into the back of host until it locks, and then screw on to fix it.

5. Step3. Place 2 silicone pads on two-part bracket, you should align the contours on the silicone pad with the grooves on the inside of the brackets; place two-part bracket with silicone pads on the selected tube, and tighten the screw until the mount does not slide on the tube. Note: You should check the tightness of the screw periodically.
   Remarks: It is recommended to install the USB charging port face down for better waterproof effect.
   Reminder: The factory comes standard with anti-loosening nuts, which is difficult to assemble and disassemble, and needs to be operated patiently.

6. Installation Method 2: Zip ties installation

7. You can choose zip ties installation if the bracket diameter is not fit to your frame diameter.

8. Rotate the other base into the bottom of the host,screw in the screw and fix it with zip ties.

9. Multifunctional Taillight and Smart Brake Function

10. Taillight Mode Button: In DISARM mode, press [ ****] on remote select light mode, it has 5 light modes: Slow Flashing→ Breathing→Blinking→Steady Light→OFF

11. Many users like intelligent auto modes, the “Slow Flashing” mode and the “Breathing” mode. The host taillight will light up for 30s and then automatically detect the brightness of the riding environment, turn off when it is bright, and turn on when it is dark. In a dim environment, if you stop for more than 30 seconds, it will automatically turn off to save power; if you ride again, it will automatically light up.

12. If you don’t want intelligent auto modes, you can select “Blinking” and “Steady Light” while riding. These 2 modes will not be affected by environmental brightness and any vibrations.

13. When the host taillight turns on, if there is a brake action while riding, the taillights will be highlighted in red for 2 seconds to remind other drivers, and then return to the previous state.

14. Anti-theft Alarm Function: Arm and Disarm

15. Arm Button: Press [ ****] arm button, host makes “Dou.Re.Mi” prompt sound, about 5s later, it makes a “Bi” sound and enter arm mode.

16. In arm mode, the host makes alarm sounds for 2s when motion or vibration is detected, if any more motion or vibration is detected within 2-12 seconds, the host will make alarm sounds for 30 seconds（. Multiple sound effect cycles）

17. Disarm Button: In arm mode, press [ ****] disarm button, host makes a “Di..” prompt sound and enters disarm mode.

18. When arming, you can press [ ****] disarm button to stop alarm and exit arm mode.

Other Function & Setting

Vehicle locate ringing function

1. Vehicle locate ringing button: Press [ ****] button, host make the selected ringtone, it helps you to remind other drivers, and can be vehicle search function. The taillight is on , then return to the previous state. ( Note: this function not available in arm mode)

Setting for sensitivity, ringing tone and volume

1. It has 7 sensitivity levels from high to low, prompt sounds – Duo Re Mi Fa Sou La Xi correspond to 7 levels. Duo sound is the highest level. (The factory default is the highest sensitivity)

2. Seting method:
   Note: it can NOT be set in arm mode. Press [ ****] disarm button before setting.

   • Step 1: In disarm mode, press and hold [ ****] disarm button, alarm makes “Bi…Bi” sound firstly, continue to press and hold until the remote indicator light go off and stay on, release after you heard a “Di” sound, host enters setting process;
   • Step 2: Press [ ****] arm button to select sensitivity level, Do Re Mi Fa Sou La Si correspond to 7 levels from high to low;
   • Step 3: Press [ ****] taillight mode button to select the ringtone that you like;
   • Step 4: To adjust the volume, press [ ****] button on the remote control continuously, 3 levels volume can be cycled;
   • Step 5: After setting, press [ ****] button on the remote control, and the host will make “Bi” sound to exit the setting function. (If no any operation within 10s, remote indicator light will go off and alarm will exit setting process.)

Note: Please know it can’ t enter setting process in arm mode. Press [ ****] disarm button before setting.

Pair More Remotes/Hosts
Host and remote have been paired when you received. If you need to pair more remotes/hosts, please see the following steps.

1. Pairing Steps:
   • Step 1. When alarm in disarm mode, press and hold [ ****] pair button on host about 3s until you heard a “Du” sound, it enters pairing process;
   • Step 2. Press any button on remote, host will make “DuDu..” sound. Done.
2. When in pairing process, press [ ****] pair button on alarm, or not any operation within 30s, host will exit pairing process.
3. When the host is waiting for pairing, press [ ****] button on alarm or if the remote control signal is not received within 30 seconds, the host will make “Bi” sound and automatically exit pairing state.
4. A host can pair up to 8 remotes, if exceeds, the ninth remote replaces the first one.
5. Delete all pairing: [Please do with caution] Press disarm button, then press and hold the [ ****] pair button of host, about 3s later it will make a “Du” sound and enter the pairing process, ignore it and don’ t release, continue to press and hold the button for 7s until it makes a “Bi” sound. Done. All remotes will be deleted.

Low Battery Warning & Charging

1. Host: If host is in low battery, when press [ ****] arm/diarm button on the remote, the host will also make low-battery prompt sounds, in addition to the arm/disarm prompt sound. Open USB-C port cover, charge with the original USB cable and your 5v power adapter (not included). When charging, the red indicator lights on, and go off when full charged.
2. Remote: If remote is in low battery, wireless range will be reduced, or, remote indicator no longer lights up or lights weak, please replace the remote control battery. (See the following diagram about how to replace battery for remote)

How to replace battery for remote
Pry at the gap with a small flat screwdriver Slides up & down then expand and open the remote.

1. Unscrew the screw with a Phillips screwdriver.
2. Pry at the gap with a small flat screwdriver, slides up & down then expand and open the remote.
3. Push out the battery with flat blade screwdriver.

Product Feature

1. Taillight/Brake light/Anti-theft alarm/Bike bell 4-in-1 function!
2. Reminding the surrounding pedestrians and drivers with light and sound warning, effectively protect the safety of the car and the rider!
3. Warning light will automatically light up when passing through a tunnel or during the night rides!
4. Brake light will be highlighted immediately when you brake or slow down!
5. Arming when parking, deterring thieves and protect your car effectively by loud alarm sound and blink light!
6. PC+ anti-UV material, waterproof and dustproof, high and low-temperature resistance, not afraid of wind, rain and severe cold and heat!
7. The 4th version of power-saving technology, long remote battery life!

Product Parameter

1. Host Battery: 3.7V 700mAh lithium battery, working time about 1~3 months, standby time about 6 months.
2. Host Charge Port: Standard USB-C 5V (some quick chargers may not be compatible)
3. Remote Battery: WL03C: 27A(12V) Alkaline battery,
4. working time about 1~2 years (5 times per day)
5. WL09C: CR2032(3V) Button battery,
6. working time about 2~4 years (5 times per day)
7. Working Frequency: 433.92MHz
8. Waterproof level: IP65 waterproof and dustproof
9. Three levels volume: 90~110 dB
10. Working Environment Temperature: -40 ~ +70℃
11. Working Environment Humidity: <80%
12. Storage Temperature: -40 ~ +70℃

Troubleshooting

Low Battery Warning & Charging

1. Check whether the remote control indicator can light up. If not or light weak, please replace the remote control battery.
2. The host is in low power consumption mode when you receive. In this mode, remote can not control the alarm. Please charge the host at least 1 minute to activate before use, otherwise remote can’t control the alarm.
3. If host have been charged and activated, remote still doesn’t work, please pair the remote and host again. For the pairing method please see 3.3.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>