ZEVNI Z-77BJQBMB-47125-Light Brass Gold Round Chandelier Lightning Instruction Manual

ZEVNI Z-77BJQBMB-47125 Light Brass Gold Round Chandelier Lightning

Item Number: Z-77BJQBMB-4712
WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save them as you may need them at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Swivel joint (1)
• (G) Knob nut (2)
• (H) Tube
• (I) Socket ring (5)
• (J) Glass shade (5)
• (K) Socket (5)
• (L) Arm (5)
• (M) Arms assembly (1)

ACCESSORIES & QTY ENCLOSED

• (A) Plastic wire connector (3)
• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

3. Unscrew knob nuts (G) from the canopy (E) then remove mounting plate (C).

4. Adjust arms (L) to the proper position.

5. According to your desired hanging height choose and use tubes (H). Then pass the fixture wires through the chosen tubes (H), swivel joint (F), and canopy (E). Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto swivel joint (F) and the top of arms assembly (M). Hand tighten till snug.

6. Attach mounting plate (C) to the outlet box with mounting screws (B).

7. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart ** Connect wires according to the below chart Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.**

8. Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre­assembled screws in mounting plate (C). Note: canopy (E) should be snug against the ceiling and knob nuts (G). If not, adjust the threaded length on the mounting plate assembly (C)

   • first, unscrew the pre­assembled hex nuts;
   • then, screw the pre­assembled screws in or out of mounting plate (C)
   • when the secure length is achieved, tighten the hex nuts and back to step 8.

9. Unscrew socket rings (I) from sockets (K), carefully place glass shades (J) on sockets (K), then secure them with socket rings (I). Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

10. Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non­abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>