ZEVNI Z-O8JFMIJ2-48W3 3 Light Bathroom Vanity Light User Guide

ZEVNI Z-O8JFMIJ2-48W3 3 Light Bathroom Vanity Light

Product Information

The product is an indoor lamp with item number Z-O8JFMIJ2-48W3. It requires installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury. The user manual must be read carefully and saved as it may be needed at a later time. The electricity must be shut off before starting any work and should not be turned on until the work is complete. The lamp weighs less than 60W per bulb and requires a voltage of 120V. The lamp should be kept away from acidic and alkaline substances to avoid damaging the surface. When replacing bulbs, the lamp should be turned off or unplugged and allowed to cool down as bulbs get hot quickly. The safety instructions in the manual are not meant to cover all possible conditions that may occur. Common sense, caution, and care must be used with any electrical products.

The product comes with a green ground screw, mounting plate, backplate, knob nut, socket, lampshade, socket ring, mounting screw, plastic wire connector, and socket wrench.

Product Usage Instructions

1. Carefully remove the fixture from the carton and ensure that all parts and accessories are included.
2. Turn off the power supply before starting the installation.
3. Secure the mounting plate to the outlet box using the mounting screws provided.
4. Connect wires according to the below chart:
   • Connect black or red supply wire to the parallel cord (round & smooth) Clear, Brown, Gold or Black without tracer insulated wire (other than green) with copper conductor.
   • Connect white supply wire to parallel cord (square & ridged) Clear, Brown, Gold or Black with tracer insulated wire (other than green) with silver conductor.
   • Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape.
   • Ensure that no wire strands are exposed and carefully tuck all wires into the outlet box.
5. Attach the back plate to the mounting plate using the previously removed knob nuts. Hand tightens until snug.
6. Attach the socket to the back plate according to the instructions provided.
7. Attach the lampshade to the socket ring and then attach the socket ring to the socket.
8. Turn on the power supply and test the lamp.

Safety Instructions

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Green ground screw (1)

• (D) Mounting plate (1)

• (E) Back plate (1)

• (F) Knob nut (2)

• (G) Socket (3)

• (H) Lampshade (3)

• (I) Socket ring (3)
  ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)

• (B) Plastic wire connector (3)

• (J) Socket wrench

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.

3. Make assembly

   • Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
   • Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
   • Step A3 » Make wire connections
     Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
     Connect ground wires according to the below chart Connect wires according to the below chart** Connect Black or Red Supply Wire to:| Connect**

White Supply Wire to:

---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  *  **Step A4 »** Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.  

NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D):

  * Unscrew the pre-assembled hex nuts;
  * Screw the pre-assembled mounting screws in or out of mounting plate (D);
  * When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
  *  **Step A5 »**
  1. Remove socket ring (I) from socket (F), and carefully place lampshade (H) on socket (F), then secure lampshade (H) by tightening socket ring (I) with socket wrench (J).
  2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

4. Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

CONTACT INFORMATION

service@zevni.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>