Zevni Z-H8A26ZMB-46W4 Modern 4 Light Black Bathroom Vanity Light Instruction Manual
- October 30, 2023
- ZEVNI
Table of Contents
Zevni Z-H8A26ZMB-46W4 Modern 4 Light Black Bathroom Vanity Light
Product Information
The product is an indoor lamp with the item number Z-H8A26ZMB-46W4. The lamp has a maximum wattage of 60W per bulb and requires a voltage of 120V. The package includes a green ground screw, mounting plate, backplate, knob nuts, socket, lampshade, and socket ring. The required tools for assembly and installation are a ladder, Philips head or flat blade screwdriver, electrical tape, pliers, and wire cutter/stripper.
Product Usage Instructions
- Before starting the assembly and installation process, make sure to turn off the electricity.
- Remove the fixture from the carton and make sure that all parts and accessories are included.
- Secure the mounting plate (D) to the outlet box with the mounting screws (A).
- Connect wires according to the below chart:
- Connect Black or Red Supply Wire to Parallel cord (round & smooth) Clear, Brown, Gold or Black without tracer Insulated wire(other than green) with copper conductor.
- Connect White Supply Wire to Parallel cord (square & ridged) Clear, Brown, Gold or Black with tracer Insulated wire(other than green) with silver conductor.
- Connect ground wires according to the below chart:
- OUTLET BOX GROUND to FIXTURE GROUND with GREEN GROUND SCREW and CUPPED WASHER.
- OUTLET BOX GROUND to FIXTURE GROUND with GREEN GROUND SCREW and DIMPLES.
- Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Attach the backplate (E) to the mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
- Make sure that the distance between the mounting surface and canopy does not exceed 3/16 inch. Correct as required.
- Make sure that the ceiling or wall can support the weight of the lamp before installation.
- Keep the lamp away from acidic and alkaline substances to avoid damaging the surface of the lamp.
- When replacing bulbs, turn off or unplug the lamp and wait until it cools down as bulbs get hot quickly.
Warning: To reduce the risk of fire, electric shock, or personal injury, it is recommended to have a licensed electrician install the lamp. Always read the instructions carefully and keep them for future reference. Never attempt any work without shutting off the electricity until the work is done. The safety instructions in this manual do not cover all possible conditions that may occur, so always use common sense, caution, and care when working with electrical products.
Item Number: Z-H8A26ZMB-46W4
WARNING: (To reduce the risk of fire, electric shock, or personal
injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
-
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
» Place the wall switch in the “OFF” position.
-
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (4)
- (H) Lampshade (4)
- (I) Socket ring (4)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. -
Place the wall switch in the “OFF” position.
-
-
Make assembly
Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside
for later installation.
Step A2: Carefully pass the supply wires from the outlet box through
mounting plate (D). Secure mounting plate (D) to the outlet box with mounting
screws (A).
Step A3: Make wire connections Connect wires as below wires connection
shown. PLEASE NOTE THAT GROUND WIRE IS BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
-
Connect ground wires according to the below chart
-
Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE : back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate assembly (D):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5: )
- Remove socket rings (I) from sockets (G), and carefully place lampshades (H) on sockets (G), then secure them with socket rings (I).
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials
such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>