ZEVNI Z-G8QEIMU2-46W3 Modern 3-Light Black Bathroom Vanity Light Instruction Manual

ZEVNI Z-G8QEIMU2-46W3 Modern 3-Light Black Bathroom Vanity Light

Product Information

The product is an electrical lamp with item number Z-G8QEIMU2-46W3. It requires installation by a licensed electrician and comes with a user manual that provides safety instructions and usage guidelines. The lamp has a maximum wattage of 60W per bulb and requires a voltage of 120V. It should be kept away from acidic and alkaline substances to prevent damage to the surface of the lamp.

Product Usage Instructions

1. Before starting any work, make sure to shut off the electricity.
2. Ensure that the mounting surface and canopy are no more than 3/16 inch apart.
3. Make sure that the ceiling or wall can bear the weight of the lamp before installation.
4. Follow the tools required as shown in the picture provided in the manual.
5. Install the mounting plate to the outlet box with mounting screws.
6. Connect wires according to the chart provided in the manual, ensuring that no wire strands are exposed.
7. Twist wires together with plastic wire connectors until tightly joined and wrap each connector with approved electrical tape.
8. Install bulbs, making sure not to exceed the maximum wattage recommended on the socket.
9. Check that everything is installed properly before turning on the light.
10. To order replacement parts, use exact wording from the illustration provided in the manual.
11. Clean the fixture with a soft cloth and avoid using abrasive materials.

Item Number: Z-G8QEIMU2-46W3

Information

WARNING: (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS

PARTS INCLUDING:

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Knob nut (2)
• (G) Socket (3)
• (H) Lampshade (3)
• (I) Socket ring (3)
  • ACCESSORIES ENCLOSED:
• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power
   • Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
3. Make assembly

• Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
• Step A2: Carefully pass the supply wires from the outlet box through mounting plate (D).
  • Secure mounting plate (D) to the outlet box with mounting screws (A).
• Step A3: Make wire connections
  • Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
  • Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
• Step A4:  Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
  • NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D):
  • Unscrew the pre-assembled hex nuts.
  • Screw the pre-assembled mounting screws in or out of mounting plate (D).
  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
• Step A5

1. Remove socket rings (I) from sockets (G), and carefully place lampshades (H) on sockets (G), then secure them with socket rings (I).
2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

1. Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

• Keep this sheet for future reference in case you need to order replacement parts.
• All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

• To clean, wipe the fixture with a soft cloth.
• Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

service@zevni.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>