esky ES811 BLE Sensor User Manual

esky ES811 BLE Sensor

PREPARE before INSTALLATION

Product Display

Packaging Inspection

Open the box, check the terminal model is correct and the accessories are complete. Otherwise, please contact your dealer.

Install battery

Selection of battery

The EK811 is a Bluetooth terminal, and it needs a button battery. please reference dealer’s opinion to select battery.

Installation battery

Open the terminal cover, and make sure the battery’s positive and negative, then insert the battery properly, and close the back cover.

Power On

The terminal standard power supply is 3V

Steps of AT Setting before tests
Start hyper-terminal connection as follows

• select the comm port of PC through which EK811 is connected with PC, as the follows
•  In Port Settings, change communication speed (bits per second) to 115200bps
• Final step is the certain AT settings necessary after 1st running of downloaded program.
•  Start connection first
• Restart EK810
•  After you see the “IIII”as the following picture, start setting.

INSTALL and OPERATION

Installation Method
The terminal is Bluetooth products, it is recommended that you follow the instructions to install.

Note:

• The following installation order, please do not inverted.
•  During the installation process, please do not supply the terminal.
• The terminal installation is divided into hidden installation and open installation.
• When the terminal is using special vehicles, hidden installation is recommended. Otherwise, open installation is chosen. (To avoid thieves’ damage, the installation location should be hidden)

Open Installation
The power connecting line we selected is provided by original cigarette lighter cord.

Hidden installation
The power connecting line we selected is provided by original the main power core. And the red line has a fuse box (3A fuse) which can play a short circuit overcurrent protection role.

Installation Site

The places that we suggest to install:

• The bottom of the front windshield decorative plates
• Around of front dashboard (epidermis as nonmetallic material)
• Below the decorative panels of rear windshield
• Inside the front bumper (should pay attention of water)
• Below the wipers plate (should pay attention of water)

Installation Notes

• Avoid put together with the emission source, for example, reversing radar, anti-theft devices and other on-board communications equipment.
• As for fixing the terminal, you can bound with ties or stick with wide sponge strength double-faced adhesive.
• The terminal has GSM antenna and GPS antenna，so the installation should ensure that the EK810face up (that is GPS toward the sky). Besides, there is no on-metallic object that obscures above the terminal.
• If your car’s windshield pasted with metal insulation layer or the heating layer, GPS receiving signal will be weakened, and it may cause GPS work abnormal. So please change the location you installed the terminal.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Information to User

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

RF warning

The device has been evaluated to meet general RF exposure requirement. This device should be installed in where that has no emission source and no metallic object obscures.

RF Exposure Compliance

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or Transmitter.

References

• eSky wireless Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>