Wittkopp L15 Primor 1000 swing bolt User Manual

**Wittkopp L15 Primor 1000 swing bolt User Manual

**

Important instructions

1. Code entry
   The electronic lock operates with a six digit code. You can programme a second opening code. Each input is confirmed by a beep and the light illuminates.
   After entering a valid code, a double signal sounds. If the code is an invalid code, you will hear a long beep. If you wait more than ten seconds, the entered code disappears and you have to enter it again.

2. Opening the safe
   Enter the six digit code (factory code 123456) and unlock the door within three seconds using the handgrip or knob. If you do not open the lock within three seconds, the lock closes again automatically.

3. Closing the safe
   Close the door and turn the handle or knob into the closed position. The lock is automatically locked. You can test whether the lock is locked by turning the handle to the open position.

4. Blocking
   If incorrect codes are entered four times in a row, the keypad blocks automatically for five minutes. The light flashes every ten seconds during this period. And if you try to use the keypad, you will hear a long signal. Entering a wrong code twice after the blocking period ends will start a new delay time of five minutes.

5. Security advice
   Once you start using the safe, change the standard factory code into your own personal access code immediately. When choosing a code, avoid obvious combinations such as numbers related to your birth date, part of your telephone number or postcode. Remember the code and keep it t yourself. If you feel the need to write it down, keep it in a safe place.

Master- or user code

1. Changing the master and user code
   Make sure that the safe door is open when you change the code. Key in a six digit code (or factory code 123456 if you use the lock for the first time).

Step| Action| Key| |
---|---|---|---|---
1.| Press and hold the ‘0’ button until the light stays on| 0| |
2.| Key in the code (or factory code 123456 for the first time)| 123456| |
3.| Enter a new code, for example 567891| 567891| |
4.| Repeat the new code, for example 567891 (the light goes out)| 567891| |

If the new code is not accepted, you hear a long signal. In that case, start again at step 1 for changing the code.
After changing the code, it is best to test the new code several times with the door open.

2. Setting the user code
   Make sure that the safe door is open when you change the code (key in the master code). Step| Action| Key| |
   ---|---|---|---|---
   1.| Press and hold the ‘1’ button until the light stays on| 1| |
   2.| Key in the master code, for example 567891| 567891| |
   3.| Key in new user code, for example 111111| 111111| |
   4.| Repeat the new user code, for example 111111 (the light goes out)| 111111| |

If the new code is not accepted, you hear a long signal. In that case, start again at step 1 for changing the user code. After changing the code, it is best to test the new code several times with the door open.

3. Deleting user
   Step| Action| Key| |
   ---|---|---|---|---
   1.| Press and hold the ‘3’ button until the light stays on| 3| |
   2.| Key in the master code, for example 567891 (the light goes out)| 567891| |

The user code has been deleted. Only the master code remains valid. If the user code deletion is unsuccessful, you hear a long signal. In that case, start again at step 1 for deleting the user code.

Opening delay and opening window

The opening delay can be 1 to 99 minutes:
This the waiting time before you can open the lock.
The opening window time can be 1 to 19 minutes:
You have to enter the code again to open the safe during this window (the period in which you can open it).

1. Programming the opening delay and opening window
   Make sure that the safe door is open while you change the opening delay and window (key in seven digit code).

Step| Action| Key| |
---|---|---|---|---
1.| Press and hold the ‘9’ button until the light stays on| 9| |
2.| Key in the master code, for example 567891| 567981| |
3.| Enter the opening delay using two digits, for example 5 minutes| 05|  |
4.| Enter the opening window using two digits, for example 1 minute| 01| |
5.| Repeat the opening delay time| 05| |
6.| Repeat the opening window time (the light goes out)| 01| |

If the light goes out during programming, you have waited too long to make an entry. In that case, start again at step 1.

2. Opening with opening delay and opening window
   Step| Action| Key| |
   ---|---|---|---|---
   1.| Enter the user or master code, for example 567891| 567891| |
   2.| The opening delay time starts, the light illuminates every few seconds| |  |

   ---

| When the opening delay has elapsed, you will hear an audible signal and the opening window begins. The light illuminates every few seconds.|  | |
4.| Enter the user or master code, for example 567891| 567891| | **
5.| Open the handgrip within 3 seconds, and the safe is open|  |  |
3. Changing the opening delay
You can only change the opening delay during the opening window. Step| Action| Key**| |
---|---|---|---|---
1.| Enter the user or master code, for example 567891| 567891| |
2.| The opening delay time starts, the light illuminates every few seconds|  | |

| When the opening delay has elapsed, you will hear an audible signal and the opening window begins. The light illuminates every few seconds.|  | |
4.| Press and hold the ‘9’ button until the light stays on| 9| |
5.| Key in the master code, for example 567891| 567891| |
6.| Enter the opening delay time using two digits, for example 20 minutes| 20| |
7.| Enter the opening window time using two digits, for example 2 minutes| 02| |
8.| Repeat the new opening delay time| 20|  |
9.| Repeat new opening window time.

The opening delay has now been changed.

| 02| |
4. Deactivating the opening delay
You can only change the opening delay during the opening window. Step| Action| Key| |
---|---|---|---|---
1.| Enter the user or master code, for example 567891| 567891| |
2.| The opening delay time starts, the light illuminates every few seconds|  | |

| When the opening delay has elapsed, you will hear an audible signal and the opening window begins. The light illuminates every few seconds.|  | |
4.| Press and hold the ‘9’ button until the light stays on| 9| |
5.| Key in the master code, for example 567891| 567891| |
6.| Key in 00 (= 0 minutes) to deactivate the opening delay| 00|  |
7.| Key in 01 to deactivate opening window| 01| |
8.| Repeat 00 to deactivate the opening delay| 00|  |
9.| Repeat 01 to deactivate opening window. The opening delay is now disabled.| 01| |

Power supply

Changing the battery
As soon as the battery is almost empty (and the voltage becomes too low), the light will flash and a warning signal will sound several times when you open the door. This is the warning that you need to change the battery.
Do not use rechargeable batteries, only high quality 9V batteries.

Model 1
The battery compartment is located behind the keyboard. You can open the lock at the top of the keyboard.

Model 2 and 3
The integrated battery compartment in the bottom of the entry unit opens by moving a slider.
Attention! You must firmly attach the battery clip to the battery.

Do you have questions about your safe, the electronic lock or is there an unexpected malfunction?
Please contact your local dealer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>