Diecast Masters 27006 Remote Controlled Cascadia Truck Instruction Manual
- June 5, 2024
- Diecast Masters
Table of Contents
Diecast Masters 27006 Remote Controlled Cascadia Truck Instruction Manual
Overview
Package includes
Tractor, Controller,
USB charger with cable,
Two AA batteries, Lithium battery,
Window box package
Product Information
Frequency: 2.4 GHz
Maximum number of users/machines without interference: 12
Controller Working Range: 30m / 98.4ft
Max. speed (km/h): 10 km/h
Scale: 1:16
Max. playtime: 40 min.(loaded) / 60min.(unloaded)
Charging time: 210 min.
Charger: 1A, USB cable
Rechargeable Battery: 1 x 7.4V 2000mAh 2S
Controller Battery: AA size x 2
Product Weight (tractor, exclude battery): 2.27kg / 4.99Ibs
Hauling Capacity: max. 5kg / 11Ibs
Daimler Trucks North America
Freightliner Trucks
2477 Deerfield Drive, Fort Mill, SC 29715
803-578-3000
www.freightliner.com
BATTERY CHARGING INSTRUCTIONS
CHARGING METHODS
Connect the white port of Li-Po to USB charging port, as shown in the Figure,
and ensure port can be connected tightly and correctly, then insert the USB
charging plug into power adapter, and perform charging.
INDICATOR LIGHT STATUS AT THE TIME OF CHARGING:
Uncharged state: red light always lit Charged state: Red light always lit + Green light flashes Full charging state: Red and green light always lit
When the battery is fully charged, please remove the USB charger lead promptly
BATTERY/USB PARAMETERS
Battery specifications: 18650 7.4V 2000mAh Li-Po
Intelligent USB balance charger with overcharge protection
Input: 5.0V 1-2A
Data change in Battery/USB PARAMETERS: Output: DC 7.4V, 800mA
Precautions Of Li-Po Batteries
- Battery can be charged only by originally configured USB charger lead.
- Be sure to charge with the white Big socket port, not the yellow socket.
- 7.4V Li-Po must be equipped with 5V USB charging plug.
- Any Li-Po battery with a damaged appearance should NOT be charged to avoid fire hazards from spontaneous combustion.
- The battery should be charged according to the specified charging time period.
Safe Usage Instructions for Li-Po Batteries
- Li-Po batteries pose a higher danger compared with other batteries.
- This company does not bear any responsibility resulting from improper usage.
- DO NOT attempt to charge the Li-Po battery with any charger other than the included original charger. Failure to do so may result in an explosion or fire. DO NOT dismantle, subject to impact, incinerate or reverse the connections of the battery. Avoid metal objects impacting the positive and negative polarities of the battery. Please prevent sharp objects from penetrating the battery to avoid the potential of fire.
- Please use caution when charging the battery and ensure charging occurs in a visible area. DO NOT leave battery unattended while charging.
- Battery should be kept out of reach of children to avoid any injury.
- A degraded battery should not be attempted to be recharged. Battery expansion, deformation, explosion or fire may occur.
- Degraded batteries should be disposed of properly following regional or national disposal guidelines to ensure protection of the environment.
WARNING
This product contains small parts and is not intended for children under the
age of 14.
The remote control requires 2 X 1.5V AA non-rechargeable batteries and the RC
model requires a 7.4 V 2000mAh Li-Po battery (included)
The RC model motor can generate heat and should not be touched to avoid
possible burns.
Periodically check the wire, plug, shell and other parts of the charger for
wear or damage and discontinue use if detected until repaired or replaced.
The RC model should only be charged using the recommended guidelines.
The LEDs (Light Emitting Diodes) can emit radiation and should not be pointed
directly at the eyes.
Aviation restrictions forbid the use of Radio Control devices within a radius
of 3 miles or 5000 meters from any airport runway or facility.
IMPROPER USE OF THIS PRODUCT
Do not dismantle, modify or otherwise alter the operation of this product in any manner. Do not operate this product in an unlawful or illegal manner or as to jeopardize the safety of the operator or others.
IMPORTANT NOTICES
Please note: This product has been manufactured under strict performance guidelines and tested to meet safety standards and requirements. This product is not intended for operators under the age of 14. The manufacturer bears no responsibility for injury or accidents resulting from the use of abnormal parts, excessive wear, improper assembly or operation. Please operate this product in a safe and responsible manner.
INSTALLATION OF REMOTE-CONTROL BATTERY
Model is equipped with a 7.4V 2000m Ah Li-Po battery (included). First, unscrew to open the battery cover, then correctly connect the battery following the diagram. Place the battery into the compartment. Close the battery cover. Tighten the cover screw to avoid children easy access.
The remote control requires 2 X 1.5V AA non-rechargeable batteries. Open the battery cover by loosening the cover screw. Place the batteries into the compartment observing the correct polarity. Replace the battery cover and tighten the cover screw.
Battery Installation Instruction:
- Remove rechargeable battery from package and install correctly in machine following included guidelines.
- The rechargeable battery should be removed from the machine before recharging.
- Recharge battery only under adult supervision.
- Do not use rechargeable AA batteries in the remote control
- Do not combine old and new AA batteries in the remote control
- Use the same type or brand of new AA batteries in the remote control
- Place AA batteries in the remote control observing the correct polarity
- Use caution to avoid short-circuit of the battery terminals in the remote control.
MODEL DRIVING CONTROL
LIGHT AND SOUND CONTROL
FRONT STEERING TUNE
5th WHEEL FUNCTION
Requirement for FCC Part 15
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ISED Statement
This device complies with Industry Canada licenseÿexempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause. interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICESÿ3 (B)/NMBÿ3(B).
This radio transmitter (ISED certification number: 25977-27006) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.