atop Technologies ATW310-32 Wireless Coordinator User Manual

ATW310-32 Wireless Coordinator
User Manual

Important Announcement

The information contained in this document is the property of Atop Technologies, Inc., and is supplied for the sole purpose of operation and maintenance of Atop Technologies, Inc. products. No part of this publication is to be used for any other purposes, and it is not to be reproduced, copied, disclosed, transmitted, stored in a retrieval system, or translated into any human or computer language, in any form, by any means, in whole or in part, without the prior explicit written consent of Atop Technologies, Inc., offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.
Disclaimer
We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual is reviewed regularly and any necessary corrections are included in subsequent editions. Suggestions for improvement are welcome. All other product names referenced herein are registered trademarks of their respective companies.
Published by
Atop Technologies, Inc.
2F, No. 146, Sec. 1, Tung-Hsing Rd.
Jubei, Hsinchu 30261
Taiwan, R.O.C.
Tel: 886-3-5508137
Fax: 886-3-5508131
www.atop.com.tw
Copyright © 2017 Atop Technologies, Inc. All rights reserved. Technical data is subject to change. All other product names referenced herein are registered trademarks of their own respective companies.

Preface

Purpose of the Manual
This manual supports you during the installation and configuring of the ATW310-32, as well as explains some technical options available with the mentioned product.
Who Should Use This User Manual
This manual is to be used by qualified personnel or support technicians who are familiar with operations;
This manual also provides helpful and handy information for first-time users. For any related problems please contact your local distributor, should they be unable to assist you, please redirect your inquiries via www.atop.com.tw
User manual Applicable models
ATW310-31; ATW310-32
Warranty Period
We provide a 1-year limited warranty.
Manufacturers Federal Communication Commission Declaration of Conformity Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Professional installation instruction

1. Installation personal
   This product is designed for specific applications and needs to be installed by a qualified person who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.

2. Installation location
   The product shall be installed at a location where the radiating antenna can be kept 20cm from a nearby person in normal operating conditions to meet regulatory RF exposure requirements.

3. External antenna
   Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of the FCC limit and is prohibited.

4. Installation procedure
   Please refer to the user’s manual for the detail.

5. Warning
   Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to a serious federal penalty.

UL listed power unit
Minimum ambient temperature 50 degrees
The ATW310-31/ATW310-32 series products are intended to be supplied by a UL Listed Power Unit marked with an “LPS” (Limited Power Source), the output rate of 12 VDC, 1A maximum.
The ATW310-32 product this unit intended to be supplied by UL Listed PoE switch or power over Ethernet complied with an LPS or PS2, and rated voltage: 44-57Vdc, 0.18A maximum.
Caution
Beginning from here there will be extreme caution exercised.
Never install or work on electrical cabling during periods of lightning activity. Never connect or disconnect power when hazardous gases are present.
WARNING: Disconnect the power and allow to cool 5 minutes before touching.

Introduction

2.1 Product Overview
The wireless coordinator is a data transmission medium between the picking control PC and all the picking devices. Which is an Ethernet architecture product, following up the standard TCP/IP communication protocol to communicate with the host PC.

Getting Started

3.1 Inside the Package
Inside the product purchased you will find the following items:
Table 3.1

Note: Please notify your sales representative if any of the above items are missing or damaged in any form upon delivery. If your sales representative is unable to satisfy your inquiries, please contact us directly.
3.2 Front & Power Panels
The Front (Figure 3.1), and Power panels (Figure 3.2), are as follow:

3.3 First-Time Installation
Before installing the device, please adhere to all safety procedures described below, Atop will not be held liable for any damages to property or personal injuries resulting from the installation or overall use of the device. Do not attempt to manipulate the product in any way if unsure of the steps described here, in such cases please contact your dealer immediately.

• Prepare the necessary cables, DC adapter, power cord, LAN cable, etc.: do not connect the unit yet.
• Install the antenna to the SMA connectors.
• Proceed then to plug the power source into the unit, starting from the ground and then the terminal block.
• Place the device in the desired location and connect it to the LAN via an Ethernet cable with a RJ45 connector.
• Connect your computer to the LAN network. Default configurations will be addressed later on in Sections.

Note: remember to please consult your Hardware Installation Guide when attempting an installation. Also, please follow all safety procedures when doing so.
3.4 System Setup
The following section describes some critical settings for the ATW310-32.
3.4.1 PC IP address
View PC Host IP Location This example is 10.3.44.1 Figure 3.3

3.4.2 Set up PC IP
Use “System controller\wptl _sys.exe” Figure 3.4

Enter the setting screen Figure 3.5

Click the “SYS ID”
Enter the setting screen Figure 3.6
“Working IP” Field is set to: 10.3..44.1.
Click Update to complete the setting

System Controller ”10. 3. 44. 1” Figure 3.7

3.4.3 Set up Wireless coordinator IP Address
Use Manager. Click ” Invite” then View Wireless coordinator IP Figure 3.8.
Wireless coordinator IP Address default IP 10.0.50.100

Click on the IP Address field and the ” Config “option. Figure 3.9

Enter the dialog screen. Figure 3.10

Modify the IP address/gateway to the same network as the PC. Figure 3.11

Click “Config Now” to complete the set, and the wireless coordinator will restart.
Click “Invite” to confirm the IP address to complete the modification. Figure 3.12

Click “Exit” exit Monitor.
3.4.4 Wireless coordinator joins the system
Use Config tool.\WPTLConfig_v.095. Figure 3.13

Enter the setting screen Figure3.14

Click the field to connect the PC. Figure 3.15

Click “connect to sys” connect PC. Figure 3.16

Check “SYS ID”
SYS ID field is 1 Figure 3.16

Click ” Add coods” and connect Wireless coordinator. Figure 3.17
The Wireless coordinator now makes a “B” sound.
Click “ok” Confirm the connection.

Wireless coordinator connection completed. Figure 3.18

3.4.5 Connect Wireless Pick To Light
Click “Coord ID/Addr”. Figure 3.19

Click “Coord config”. Figure 3.20

Set up Wireless Pick To Light channel.
CH.Mode field options” FIX”
Channel List field Select a Wireless Pick To Light channel Default channel 1 this example is 8.
New Tag Association field options” open”
Click “APPLY” Figure 3.21

Click “Add Tags” and enter the List of new Tag detected on screen Figure 3.22

Start setting Wireless Pick To Light ID address.
Before setting, you must confirm that the tag displays PEND before setting. Figure 3.23

Setting Wireless Pick To Light ID address. Figure 3.24
Step1. Press and hold the B key.
Step2. Press and hold the A key. (about 1s).
Step3. Release the A key.
Step4. Press the C key to complete the ID Address setting.

If TAG does not show PEND status, please follow the steps below. Figure 3.25

Step1. Press and hold the A key.
Step2. Single-click the C key. The LCD will display TSTAG.
Step3. Release the A key.
Step4. Single-click the B key. The LCD will display DEFLT.
Step5. Single-click the C key. The LCD will Final display PEND.
Click “OK”. Complete the Wireless Pick To Light ID Address setting. The screen will display Tag ID-related information as shown below. Figure 3.26 & 3.27

Specifications

4.1 Hardware Specifications
Table 4.1

selectable by Menu control. Transmit Power: Up to 14dBm + 3dBi antenna. Receive Sensitivity: Up to -95dBm.
Data Rate: 500Kbps Extend Antenna attached.
Radiation: Omni-Directional.
Distance cover range: Indoor 25 M
LAN| IEEE 802.3 Standards
Support TCP/UDP Client/Server connection mode. 10/100/1000 Base-T/TX RJ-45 Connector.
Auto-Negotiation (10/100/1000Mbps, Half/Full-Duplex). Auto-Crossover Detection.
1.5KV Magnetic Isolation Protection.
USB Port| USB2.0 I/F model, Provide +5VDC,0.5A.
Support assign WiFi Module for Communication (Option). Support Storage Device EXT3,32GB.
Connector Type-A w/Lock.
Item| Description
---|---
COM| Extend RS-485 port (Reserved). Proprietary protocol.
Connector: Terminal Block/Male/3.81mm pitch/4pins.
Pin Assign: NC/D+/D-/G
LED indication| PWR: Power Indicator x 1
RUN: System Status Indicator x 1
Tx/Rx: Between Host & Device Communication x 2. RF: Wireless status Indicator x 1.
AN Indicator: Link & Speed Indicator x 2.
Reset/Default| Reset: Hold 3sec to Reboot the device.
Default: 6sec Reset to Factory Default & reboot.
Buzzer| Build-in Buzzer beeper.
Power Requirement| Input:
Voltage: DC +12VDC +/-10% Max. Current: 1A max. @ 12VDC.
Connector Type:
1.  DC-JACK(Inner V+, 2.1mm).
2.  Terminal block (V+/V-/F.G.; Pitch:5.08mm /3pins/Male). Case Shielding Ground: M4 + Screwing.
PoE IEEE802.af PD (option ATW310-32):
Rated Voltage: 44-57Vdc, Current: 0.18A Maximum Protection:
1. Inrush Current Protection.
2. Power Voltage Reverse Protection.
Operation Temperature| Operation:    -10 to 50℃ (14 to 122℉)
Storage:       -20 to 60℃ (-4 to 140℉)
Ambient Humidity| Operation & Storage: 5 ~ 90% (non-condensing).
Housing| Size: 148mm x 125mm x 33mm ( 5.83 x 4.92 x 1.30 in). Material: Metal Case.
Weight: 0.61kg (1.33 lb)

4.2 Three View Drawing:

4.3 Installation overview
Step 1. Use 4pcs M4 * 16mm, button Phillips to fix the product to the wall or beam.
Step 2: Connect one end of the ground wire to the product ground screw and the other end to a protective ground terminal block.
Warning!
The equipment shall connect one end of the ground wire to the product ground screw and the other end to a protective ground terminal block.
Step 3. Connect the network cable and power cable.

4.4 LED Indicators
Table 4.2

Warranty

Limited Warranty Conditions
Products supplied by us are covered in this warranty for undesired performance or defects resulting from shipping, or any other event deemed to be the result of Atop Technologies’ mishandling. The warranty does not cover, however, equipment that has been damaged due to accident, misuse, or abuse, such as:

• Use of incorrect power supply, connectors, or maintenance procedures
• Use of accessories not sanctioned by us
• Improper or insufficient ventilation
• Improper or unauthorized repair
• Replacement with unauthorized parts
• Failure to follow Our operating Instructions
• Fire, flood, “Act of God”, or any other contingencies beyond our control.

RMA and Shipping Reimbursement

• Customers must always obtain an authorized “RMA” number from us before shipping the goods to be repaired.
• When in normal use, a sold product shall be replaced with a new one within 3 months upon purchase. The shipping cost from the customer to us will be reimbursed.
• After 3 months and still, within the warranty period, it is up to us whether to replace the unit with a new one; normally, as long as a product is under warranty, all parts and labor are free of charge to the customers.
• After the warranty period, the customer shall cover the cost of parts and labor.
• Three months after purchase, the shipping cost from you to us will not be reimbursed, but the shipping costs from us to the customer will be paid by us.

Limited Liability
Atop Technologies Inc., shall not be held responsible for any consequential losses from using our products.
Warranty
Atop Technologies Inc., gives a 1-year max for Wireless coordinators.

Atop Wireless coordinator
ATW310-31/ATW310-32
V. 1.0
Dec. 2019

References

• ATOP Technologies - Shaping Industrial Connections
• ATOP Technologies - Shaping Industrial Connections

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>