Koala Kare KB310-SSRE Recessed-Mounted Baby Changing Station Instruction Manual

: June 5, 2024
: Koala Kare

Table of Contents

Koala Kare KB310-SSRE Recessed-Mounted Baby Changing Station
Operations Instructions
- ASTM F2285-04 (2016)
Installation Instructions
**Hardware Provided
INSTALLATION
Koala Kare Products A Division of Bobrick
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Koala Kare KB310-SSRE Recessed-Mounted Baby Changing Station

Koala-Kare-
KB310-SSRE-Recessed-Mounted-Baby-Changing-Station-
PRODUCT

Important: Retain for future reference. Read carefully.

The KB310 Baby Changing Stations have been designed to meet the following applicable provisions of the 2010 ADA Standards (ADAS) and the 2009/2017 International Code Council (ICC) A117.1 Standards and the 2012 Texas Accessibility Standard (TAS) when properly installed and maintained. To comply with these accessibility requirements the unit must be installed in a compliant location and height in accordance with the installation instructions. You are responsible for the safe operation of this unit.

Operations Instructions

Please Note

To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Baby Changing Stations have been tested to hold a substantially static load. The unit must be attached to a permanent wall that is capable of holding a substantial load. The maximum recommended total weight for this baby changing station is 50 lbs. Excessive weight may cause a hazardous or unstable condition to exist.

Inspection Criteria

A properly maintained baby changing station:

Opens and closes smoothly.
Has a functioning strap and buckle. The strap is held firmly in place when the buckle is depressed over it.
Offers parents liners through a fully stocked liner dispenser. (Dispenser built into the unit.)
Provides a clean, convenient place for customers to attend to their children.

Restraint System

Check the strap by releasing the lever on the buckle and pulling one end of the strap up through the bottom of the buckle, depressing the lever when the strap is tight. Give the strap a tug in the horizontal direction away from the buckle, checking that the strap remains in place beneath the buckle. To loosen the strap, release the lever and pull the strap from the bottom of the buckle.

ASTM F2285-04 (2016)

WARNING

Never leave the child unattended.
Avoid serious injury from falling or sliding out. Always use a restraint system.
Designed for Infants Only. Age up to 3.5 years and weighing less than 50 lb (22.7 kg). Keep one hand on the child at all times.
Parcels or accessory items, or both, placed on the unit may cause the unit to become unstable.
Never leave child unattended.
Avoid serious injury from falling or sliding out.
Always use a restraint system.
Designed for Infants Only. Age up to 3.5 years and weighing less than 50 Ib (22.7 kg). Keep one hand on child at all times.

Replacement Parts

For a list of replacement parts for this product, (such as straps, shocks, and labels) please visit www.koalabear.com.
Replacement parts and additional liners can be purchased from your local distributor or direct from Koala at www.koalabear.com.

ADA Requirements

Additional information on how this product complies with ADA requirements can be found in the KB310 & KB311 Baby Changing Stations Accessibility Compliance document on www.koalabear.com.

Installation Instructions

Tools Needed

**Hardware Provided

Koala-Kare-KB310-SSRE-Recessed-Mounted-Baby-
Changing-Station-FIG-2 **

Scan the QR code to view the installation video and to find product resources. Also available at:

www.koalabear.com/product-catalog/kb310-sure/

INSTALLATION

Step 1

Prepare the rough wall opening per the Technical
Datasheet. Make sure the top of the bottom stud is at 26 9/16″ (675mm) to ensure the correct mounting height. Fig. 1 For more information navigates to www.koalabear.com.
Be sure to wear safety gloves to protect your hands from the product’s exposed metal edge.

Step 2

Remove the handles and bag hook from the packaging and set to one side.
Open the unit by pulling up on the handle mounting studs and remove the plastic liner dispenser from inside the unit and set to one side.

Step 3

With the assistance of a second person, lift and position the unit into the rough wall opening.
Have one person hold the unit and place it into the wall while the other opens the unit using the handle mounting studs.

Step 4

Open unit fully and you will have access to the six mounting holes on either side of the unit. Fig. 2
Using the hardware provided, predrill and screw through the mounting holes. Do not over-tighten.
Once secured, the unit will no longer need to be held in place.

Step 5

With the unit open, take the liner dispenser and position it over the exposed metal frame in the center of the recess.
Use the provided key to open the liner dispenser. This will provide access to the four mounting holes.
Use the provided hardware to secure the liner dispenser to the metal frame. Fig. 3
Lock the liner dispenser and close the unit.

Step 6

Take one of the provided handles and position it over the handle mounting studs, so that the open portion is toward the top of the unit.
Use provided Allen wrench to tighten the set screws in the handles, securing it to the handle mounting studs. Fig. 4
Repeat for the opposite handle.

Step 7

Test the unit by opening and closing multiple times, ensuring it opens and closes smoothly.
Remove protective film from the surface of the unit.

Step 8

To install the bag hook, measure up 44″ from the finished floor in the desired location and mark the wall. Fig. 5
Position the bag hook on the wall so that the top of the mounting plate is level with the 44″ mark.
Position the bag hook over a wall stud for optimal strength.
Mark then predrill the mounting holes.
Use the provided screws to secure the bag hook in position, then take the escutcheon plate and screw it over the mounting plate to cover the mounting screws. Fig. 6