CLEANAIRE UV04-S80-PU UVC Disinfecting Strip Light User Guide

CLEANAIRE UV04-S80-PU UVC Disinfecting Strip Light

PACKAGE CONTENTS AND INSTRUCTIONS

INSTRUCTIONS

MANUAL OF REMOTE CONTROL (PLEASE SELECT MODE BEFORE USING)

1. Lamp should be paired with the included remote. To reconnect remote power the unit on and press the 120min button for 5 seconds.
2. Lamp has two modes Standard mode & Automatic mode, switch button is located under the battery.

STANDARD MODE (DEFAULT)
If movement is detected the unit will turn off and will not automatically turn back on without manually pressing the on button.

AUTOMATIC MODE:
If movement is detected the unit will turn off and will automatically turn back on after 2 minutes with no motion detection.

1. Press the lock button to start, select mode and lamp will turn on 20 seconds after alert beeps.
2. Five available disinfection settings.
3. Press off to cancel the time setting.

START UP WARNING DESCRIPTION:
Prior to turning on the lamp has an intermittent or continuous sound and light warning feature that indicates the UVC lamp is about to turn on. This is a warning to leave the disinfecting area as soon as possible to prevent injury from UVC exposure.

SENSOR DESCRIPTION:
3D Sensor detection: 1 Microwave sensor + 1 PIR sensors provide 360-degree motion detection. The lamp will turn off automatically when motion is detected.

BATTERY MANUAL INSTRUCTION:
Remove the tape from the battery prior to use. ( Model: CR2032 3V).

TECHNICAL SPECIFICATIONS

Operating temperature :14°F ~ 95°F,
Operating environment humidity: <80% ,
Storage temperature: -4°F ~ 140°F,
Sensor detection range: 360 degrees,
Sensor detection distance: 0-16 ft.,
Sensor type: 1Microwave + 1 PIR sensor,
Remote control distance: 30 ft.
Principles and Sterilization factors
Sterilization factor: Ultraviolet 253.7nm
The principle of sterilization: Use the C-band ultraviolet light emitted
by the ultraviolet lamp to destroy the bacteria and DNA of bacteria for sterilization.

APPLICATIONS
The product is suitable for the disinfection of indoor places such as offices, schools, hospitals, residential spaces, small businesses, restaurants,s, and bars.

INSTALLATION

UVC OPERATION INSTRUCTIONS FOR LAMP TUBE INSTALLATION

Cautious:

1. Please make sure the input voltage within the range on the lamp.
2. Before installation remove wire guard and remove protective covering.

WIRING INSTRUCTION

INSTALLATION INSTRUCTIONS OF PLUG

1. Use tools to open the lamp cap.
2. Install the cover on the plug head, put the cable through the plug hole, and connect the cable according to the corresponding color, and the excess wires are placed in the trunking box, and the cover is screwed on with screws to complete the installation.

INSTALLATION DIAGRAM (SURFACE AND SUSPENDED)

DIFFERENT INSTALLATION

UVC LAMP SUGGESTED AREA AND TIME

Model# 64402101 (UV03-S40-PU) 2ft UVC Strip light

Room Size (ft2)| 100 SQFT (10ft x 10ft)| 200 SQFT (10ft x 20ft)| 300 SQFT (15ft x 20ft)| 400 SQFT (20ft x 20ft)
---|---|---|---|---
Suggested Operating Time (mins)| 30| 60| 90| 120

Model# 64403101 (UV04-S80-PU) 4ft UVC Strip light

Room Size (ft2)| 200 SQFT (10ft x 20ft)| 400 SQFT (20ft x 20ft)| 600 SQFT (20ft x 30ft)| 800 SQFT (25ft x 32ft)
---|---|---|---|---
Suggested Operating Time (mins)| 30| 60| 90| 120

PRECAUTIONS FOR USE

1. If the ambient temperature is too high ( above 95°F) the PIR sensor distance will be shortened. Do not install the lamp in direct air flow ( such as: cold/hot water outlets, exhaust fan, or near electric furnace, etc.) Do not block or cover the sensor head as PIR sensors could fail to work properly.
2. There should be no heavy vibration at the installation location as it can cause the unit to shut down.
3. Multiple lights need to be separated by more than 3 feet to prevent unwanted detection.

TROUBLESHOOTING

Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.

1

| No beep

(the indicator light is off)

| 1.Confirm power is connected;

2.Confirm whether the remote control has a battery and whether the positive; and negative batteries are installed correctly;

2

|

Remote does not work

| Confirm whether the lamp is powered on. If the lamp is powered on, press the remote control “LOCK” first, and then press other function buttons; if the voltage of the remote control battery is too low, the battery needs to be replaced;
WARNING

1.  UVC exposure is harmful to humans and animals. Prevent any exposure by leaving prior to the unit turning on.

2.  In severe cases, headache, dizziness, increased body temperature, eye irritation, or decreased vision, skin irritation, itching, swelling, etc. Please consult your doctor immediately.

|  |   WARNING
UV-C emitted from this product.

Avoid eye and skin exposure to unshielded product. Follow installation instructions and user manual.

ADDITIONAL NOTE

1. The product cannot be used for lighting purposes.
2. This product is only intended for disinfecting surface objects and surrounding air. This product is not to be used to disinfect the human body and can be dangerous to humans and animals.
3. Use with caution damage can occur to objects that are not resistant to ultraviolet rays.
4. After disinfecting, please put away the product and the remote control to avoid accidental light on and accidental injury.
5. If UV disinfecting lamp is accidently broken handle with extreme care. Ventilate the area and use gloves to clean up, The lamp contains mercury do not vacuum up with a standard vacuum cleaner as it can create dust & mercury vapor.
6. If the lamp accidentally touches skin wash thoroughly, handle broken glass with gloves.
7. This product is not food rated or to be used over food prep areas.
   NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARRANTY

This product is warranted for a period of 2 years from the date of original purchase against defects in materials and workmanship. If this product should fail to operate due to defects in material or workmanship within 24 months of purchase, see www.ETiSSL.com for details. This product will be repaired or replaced, at ETi’s option. This warranty is expressly limited to repair or replacement of the product, and liability for direct, incidental, or consequential damages is hereby expressly excluded. Some states do not allow exclusions
of direct, incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty gives the consumer specific legal rights, which vary from state to state. WARRANTY IS VOID IF THE PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.

FOR ASSISTANCE, CALL: Customer Service Line
8 a.m. – 5 p.m., CST, Monday – Friday
1-855-ETI-SSLI (1-855-384-7754)
720 Northgate Parkway Wheeling, IL 60090 3/3

References

• ETi Solid State Home - ETI SSL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>