NAVEE K3A-N30BU Electric Scooter Owner’s Manual
- June 12, 2024
- NAVEE
Table of Contents
NAVEE K3A-N30BU Electric Scooter
Product Information
The product is a scooter that requires regular maintenance to keep it in good condition and ensure safety during usage. It has a main chassis, tires, screws, handlebar assembly, and a rechargeable lithium-ion battery pack.
Product Maintenance
- Cleaning: Wipe the main chassis with a soft damp cloth. For hard-to-remove dirt, use a toothbrush to scrub. Afterward, wipe all areas with a dry cloth.
- Battery: Charge the scooter at a suitable temperature. The battery charger indicator turns red when charging and green when fully charged. Fully charge the scooter before leaving it unused for a long time, and charge it every 60 days.
- Tire Inflation: Check the tire pressure every month. If the pressure is low, inflate the tires until the pressure reaches 34-38 psi. Remove the tire valve cap, connect the pump securely to the valve, inflate the tire, and then install the tire valve cap.
- Adjusting Mechanical Brake: This process is not explained in the provided text. Please refer to the user manual for detailed instructions.
- Maintaining Screws and Handlebar Assembly: This process is not explained in the provided text. Please refer to the user manual for detailed instructions.
Product Usage Instructions
- Cleaning: Use a soft damp cloth to wipe the main chassis of the scooter. For hard-to-remove dirt, scrub with a toothbrush. Finally, wipe all areas with a dry cloth.
- Battery Charging: Charge the scooter at a suitable temperature. The battery charger indicator will be red during charging and turn green when fully charged. The control panel will also display the charging status.
- Tire Inflation: Check the tire pressure every month. If the pressure is low, inflate the tires until the pressure reaches 34-38 psi. Remove the tire valve cap, securely connect the pump to the valve, inflate the tire, and then install the tire valve cap.
- Adjusting Mechanical Brake: Please refer to the user manual for detailed instructions on adjusting the mechanical brake.
- Maintaining Screws and Handlebar Assembly: Please refer to the user manual for detailed instructions on maintaining the screws and handlebar assembly.
- Battery Disposal: Before disposing of the scooter, follow these steps to remove the batteries properly: a. Ensure the scooter is disconnected from the power supply and use up the batteries. b. Unscrew the bottom cover of the scooter and remove it. c. Unplug the battery connector and remove the batteries without damaging the battery case.
Always follow the provided instructions and warnings in the user manual for safe and proper usage of the scooter.
Maintenance
Cleaning
- Before cleaning the scooter, you must turn off the power, unplug the charging cables and close the charging cover tightly.
- Wipe the main chassis with a soft damp cloth, the hard-to-remove dirt can be scrubbed with a toothbrush.
- Afterwards, wipe all areas with a dry cloth.
WARNING
- Do not wash the scooter with a high-pressure water spray.
- Do not clean the scooter with corrosive cleaner, which will damage the external and internal structure of the scooter.
Battery
- Always charge before exhausting the battery to prolong the battery’s lifespan.
- When riding, storing or charging, do not exceed the specified temperature limit (refer to specifications). Failure to follow instructions for use, , storage or charging may result in battery damage, failure to charge and void warranty.
- The fully charged scooter has an approximate standby time of 120-180 days. If it is not used for a long time, it should be charged every 30 days. Please pay attention to the standby time to prevent irreversible damage to the battery caused by not charging.
WARNING
- Do not use battery packs of other models or brands, as there may be a safety risk.
- Only use the original battery charger to avoid potential damage or fire.
- If the battery is damaged or soaked with water, do not charge or continue to use it.
- Do not remove the battery. Removing the battery is complicated, and improper operation may affect the operation of the scooter.
Storage
- If the scooter will not be used for an extended period, fully charge it, then turn it off and store it in a cool, dry place.
- Make sure the scooter is turned off when being transported and kept in its original packaging if possible.
WARNING
- Please do not leave the scooter under hot sun or severely humid place for extended periods of time.
- Please do not place the scooter near flammable materials.
- This product contains a built-in lithium battery and must be transported only when permitted by local laws and regulations.
Inflate the Tire
Check the tire pressure every month, and inflate the tires if the pressure is too low. The recommended tire pressure is 34-38 psi.
- Remove the tire valve cap, and connect the pump and the valve securely together.
- Inflate the tire.
- Remove the pump and install the tire valve cap.
WARNING
- Tire removal is very complicated. Please do not remove the tire by yourself. Improper operation may affect the operation of the scooter. Please contact professional support.
Adjust the Mechanical Brake
Tool: 8 mm T-handle socket wrench (the tool needs to be prepared by the user).
Before adjustment, make sure the scooter is powered off and not charging. When the brake is too tight, use the tool to turn the nut on the screw rod counterclockwise, so as to slightly shorten the brake cable’s exposed bottom part. When the brake is too loose, use the tool to turn the nut on the screw rod clockwise, so as to slightly lengthen the brake cable’s exposed bottom part.
Scooter Maintenance Schedule (Recommended)
Maintaining the scooter regularly can help keep the scooter neat and in good condition, avoid safety hazards, minimize breakdowns, slow down the deterioration of the scooter, and extend the scooter’s service life.
Item| Service Object| Actions| Every month| Every 3 months| Every 500 km/
6 months
| Every 1000 km/
1 year
| Every 10000 km/
3 years
---|---|---|---|---|---|---|---
Tires
| Tire Pressure| Inflate the tire until its pressure reaches
34-38 psi.
| √| | √| √| √
Tire Tread Wear| Check whether the tire is cracked, deformed, worn, etc.| |
|
√
|
√
|
√
Screws
|
Handlebar Assembly Screws
| | |
√
|
√
|
√
|
√
Tighten the accelerator screw (with the recommended torque of 0.95 ± 0.1 N·m).| | | |
√
|
√
Tighten the brake lever screw (with the
recommended torque of 7 ± 0.2 N·m).
Functions
|
|
| | |
√
|
√
|
√
---|---|---|---|---|---|---|---
| Charge the scooter at a suitable temperature. The indicator on the battery charger is red when the scooter is charging, and turns green when the scooter is fully charged. The control panel will show the charging status simultaneously during charging.| | |
√
|
√
|
√
| Turn the handlebar 60° to the left and right to make sure the turning angle is correct and the steering is free from resistance and stagnation.| | | |
√
|
√
Important Components| | Fully charge the scooter before leaving it unused for a long time, and turn it on to charge every 60 days.| | | | |
√
Specifications
Product
| Name| NAVEE Electric Scooter
---|---|---
Model| K3A-N30BU
Dimensions| Vehicle: L x w x H1’1| 44.4 x 19.3 x 47.2 in (1128 x 490 x 1200
mm)
After Folding: L x w x H| 44.4 x 19.3 x 20.9 in (1128 x 490 x 531
mm)
Net Weight| Vehicle Net Weight| 31.7 lbs (14.4 kg)
Rider
| Load Range| 55.1-220.5 lbs ( 25-100 kg)
Age| 16-50 years
Body Length| 3’11” -6’6″ (120-200 cm)
Assembled Electric Scooter
| Max. Speed| 18.6 mph (30 km/h)
General Range1’1| Approx. 18.6 miles (30 km)
Max. Climbing Angle| Approx. 20%
Suitable Surfaces| Cement or asphalt road, with benches of less than 1 cm or
crevices narrower than 3 cm
Operating Temperature| 14-122 ° F ( -1 0 to 55 °C )
Storage Temperature| 32-113 ° F (0 to 45 °C)
IP Rating| IPX4
Charging Time| Approx. 5-6 h
Battery Pack
| Model| FS011-02
Nominal Voltage| 36 V
Max. Charge Voltage| 42.5 V=
Rated Energy| 280.8wh
Intelligent Battery Management System| Over-heating, short circuit, over-
current, over-discharge, and over-charge protection
Normal Charging Temperature Range| 32 – 104 ° F (0 to 40 °C)
Rated ca pacity| 7.8Ah
Wheel Motor| Rated Power| 300 W (0.3 kW)
Battery Charger
| Output Power| 630 W (0.63 kW)
Input Voltage| 100-240 v-
Max. Output Voltage| 42.5 V=
Rated Output| 42.0 V=l.5 A
Model131| FY0634201500
Tire| Front & Back Tires| 10 Inch Pneumatic Tyre
Bluetooth
| Frequency Band| 2402~2480MHz
Max. RF Power| 0.69dBm
- Vehicle height: From the ground to the top of the scooter.
- General range: Measured when there is no wind and iS at 77 ° F (25 ° C), the scooter is fully charged to ride at a constant speed of 9.3 mph (15 a km/h) on a flat surface with a load of 165.3 lbs (75 kg).
- To recharge the battery, only use the battery charger provided in the package. Please see battery charger parameters in Specifications.
FAQ
When the product fails, please refer to the following methods when trying for a solution:
| Problem Type | Reason | Solution |
|---|
The display screen is black.
| This scooter is exposed to direct sunlight or heat for a long time.| Put the scooter in a cool place for a period of time until cooled enough for use.
The value is inconsistent with the actual value.
|
Incorrect or missing parameter setting.
| Hold down the power button to turn off and then press again to restart the scooter.
The digital display is dim.
|
Poor battery contact or no battery power.
| Turn off the power, and then turn it on again. If the fault still exists after the battery is charged, please contact the manufacturer or dealer.
The stem becomes unstable
|
The screw at the joint of the stem and the folding seat is loose.
| Lower the column, loosen the three screws in order to raise the column, next tighten the screws at the back of the pole, and then lower the pole and finally tighten the three previously loosened screws to correct the problem.
If the product cannot operate normally, please check whether the following checks have been completed.
| a. Check that the power is on.
b. Check the battery level on the display.
c. Check whether the left brake lever and mechanical brake are properly in place.
d. Check that all sockets and connections are properly connected.
If all steps have been completed and the product still does not work properly, please contact the manufacturer or dealer.
The controller is damaged.
| Do not replace the controller without authorization.
Please contact the manufacturer or dealer, do not disassemble the product without authorization.
Troubleshooting
| Error | Error Message | Solution |
|---|
El
| ****
Rx Communication Failure
| Check whether the tail light is on, if not, replace the controller or
instrument. If it is on, please check whether the wire connection between
controller and the instrument.
E2| Braking Error| Check the wire connection or replace the brake level.
E3| Accelerator Error| Check the wire connection or replace the accelerator.
E4
| ****
Wheel Motor Error
| Check whether the wheel motor and the controller cord are well connected or
replace the motor.
ES| Controller Error| Check the controller wire connection or replace the
controller.
E6| Overheating Warning| Wait until the motor temperature normalizes before
resuming use.
Certification
FCC Supplier’s Declaration of Conformity
This supplier’s declaration of conformity is hereby for
- Product: NAVEE Electric Scooter
- Model Number(s): K3A-N30BU
- Brand/Trade: NAVEE
We declare that the above mentioned device has been tested and found in
compliance with CFR 47 Part Regulation.
Responsible Party-U.S.Contact Information
- Company: Brightway Innovation Intelligent Technology (Suzhou) Co., Ltd.
- Address: Building A2, Shangjinwan Headquarters Economic Park, No.2288, Wuzhong Avenue, Wuzhong Economic Development Zone, Suzhou Jiangsu P.R. China
- Country: China
FCC STATEMENT
FCC Compliance Statement for USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Note
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
- The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
Environmental Instructions
The scooter contains a rechargeable lithium-ion battery pack, and improper disposal of these batteries will cause harm to the environment. Follow the steps below to remove the batteries before disposing of the scooter and discard the batteries properly:
- Before removing the batteries, it is better to use them up and make sure the scooter is disconnected from the power supply. Then unscrew the bottom cover of the scooter to remove it.
- Unplug the battery connector, and then remove the batteries. Do not damage the battery case to avoid any risk of injuries. Do not use the battery if it is damaged, has a strange odor, emits smoke, or gets overheated. Keep a leaking battery away from other objects.
- Discard the removed batteries at a professional recycling facility.
Warranty and service
If the product is within the warranty period from the date of your purchase, we will repair, replace or return it free of charge as the case may be if it is confirmed by the manufacturer or dealer that it is faulty or damaged due to quality defects under normal use. Unless otherwise specified by relevant laws, the product or component used for replacement may not be new, but nevertheless performs well and is equivalent, at least, to the original product or component in function. The warranty period is calculated from the first date of purchase of the product, subject to the invoice date. If there is no valid invoice, the warranty period shall be calculated from the date of delivery plus thirty (30) days. If the invoice date is later than the actual delivery date of the product, the warranty period shall be calculated from the actual delivery date. The repaired or replaced products shall continue to enjoy the warranty for the rest of the warranty period, but not less than thirty (30) days. For warranty application, please contact the manufacturer or distributor of the product and follow the instructions. When applying for warranty, an accurate, complete and clear valid sales invoice should be provided.
The above warranty does not apply to failure, malfunction or damage caused by: (a) misuse, abuse or improper transportation, maintenance or storage, such as but not limited to use, storage or maintenance under improper temperature, humidity or other improper environmental conditions; (b) force majeure or accidents, network or power interruption and other reasons beyond our reasonable control: (c) repair or removal without authorization from the manufacturer; (d) the way in which damage has been caused by any third party products or services shall be specified (purposes other than those for which the product has been designated or intended: (f) using the product in violation of the product instructions: (g) using the product for commercial purposes; or (h) the accumulated mileage recorded by the scooter body has exceeded 2000 km. Normal wear and tear or aging, scratches, abrasions and problems caused by the use of coatings, solvents or other chemicals during general use of the product do not fall within the scope of the warranty. If the original identification label of the product is changed or damaged, this warranty will be invalid. The integrity and completeness of the products and of the attached materials are not within the scope of the warranty .. You should inspect the products on the spot when receiving them and object immediately to any ascertained discrepancies/ies. The above warranty statement applies to our products. This warranty grants specific legal rights and other rights you may have according to the law. Nothing in this document affects your rights in a fashion that is not susceptible of exclusion or restriction in accordance with law.
Warranty information for the product
This product is the same as any mechanical parts. The scooter can bear high stress and wear. Various materials and components scooter’s machinery, axle) may react differently to wear or fatigue. If the component have reached the expected service life, they may break suddenly, causing the risk of injury. If any problem is found, please repair and replace the parts in time. If there are cracks, scratches and discoloration in the area under high load, it indicates that the component has exceeded its service life. Please contact the manufacturer or dealer to replace the component as soon as possible. Navee provides warranty service according to local regulations, but different parts have different warranty periods. For details, please consult the official Navee or local dealer.
Warranty card
When purchasing the product, we recommend that you clearly fill in the following information and affix the sales seal to protect your legitimate rights and interests:
For more information & after-sales support, contact us via service@navee.tech/www.naveetech.com
Safety Warning
-
Danger!
- Read user manual before use.
- For indoor use only (for the charger).
-
WARNING
- Crush Hazard
-
WARNING
- Mind Your Hand
-
WARNING
- No step!
-
WARNING
- Read carefully and keep for future reference.
-
WARNING
- Hot Surface! Do not touch the surface near this symbol.
-
WARNING
- Sharp Edges. Do not touch the sharp edges or corner.
-
WARNING
- Pinch Point
-
WARNING
- Do Not Disassemble
Innovation, Science and Economic Development Canada (ISED) Caution
This device complies with Innovation, Science and Economic Development Canada (ISED) licence exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement.