Cisco MT0 Hardware Routing Configuration User Manual

: June 5, 2024
: Cisco

Table of Contents

Cisco MT0 Hardware Routing Configuration
Features
Hardware Integration
FCC Compliance Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Cisco MT0 Hardware Routing Configuration

Features

Bluetooth 5, JEEE 802.15.4-2006, 2.4 GHz transceiver

95 dBm sensitivity in 1 Mbps Bluetooth low energy mode
103 dBm sensitivity in 125 kbps Bluetooth low energy mode (long range)
20 to +8 dBm TX power, configurable in 4 dB steps
On-air compatible with nRF52, nRF51, nRF24L, and nRF24AP Series
Supported data rates:
- Bluetooth 5-2 Mbps, 1 Mbps, 500 kbps, and 125 kbps
- IEEE 802.15.4-2006 250 kbps
- Proprietary 2.4 GHz -2 Mbps, 1 Mbps
Single-ended antenna output (on-chip balun)
128-bit AES/ECB/CCM/AAR cO-processor (on-the-fly packet encryption)
4.8 mA peak current in TX (0 dBm)
4.6 mA peak current in RX
RSSI (1 dB resolution)

ARM Cortex -M4 32-bit processor with FPU, 64 MHz

212 EEMBC CoreMark score running from flash memory
52 A/MHz running CoreMark from flash memory
Watchpoint and trace debug modules (DWT, ETM, and ITM)
Serial wire debug (SWD)

Rich set of security features

ARM TrustZone Cryptocell 310 security subsystem
NIST SP800-90A and SP800-908 compliant random number generator
AES-128-ECB, CBC, CMAC/CBC-MAC, CTR, CCM/CCM
Chacha20/Poly1305 AEAD supporting 128- and 256-bit key size
SHA-1, SHA-2 up to 256 bits
Keyed-hash message authentication code (HMAC)
RSA up to 2048-bit key size
SRP up to 3072-bit key size
ECC support for most used curves, including P-256 (secp256r1) and
Ed25519/Curve25519
Application key management using derived key model

Secure boot ready

Flash access control list (ACL)
Root-of-trust (RoT)
Debug control and configuration
Access port protection (CTRL-AP)

Secure erase

Flexible power management

1.7 V to 5.5 V supply voltage range
- On-chip DC/DC and LDO regulators with automated low Current modes
1.8 V to 3.3 V regulated supply for external components
Automated peripheral power management
Fast wake-up using 64 MHz internal oscillator
0.4 A at 3V in System OFF mode, no RAM retention
1.5 uA at 3V in System ON mode, no RAM retention, wake on RTC

1 MB flash and 256 k8 RAM

Advanced on-chip interfaces

USB 2.0 full speed (12 Mbps) controller
QSPI 32 MHz interface
High-speed 32 MHz SPI
Type 2 nearfield communication (NFC-A) tag with wake-on field
- Touch-to-pair support
Programmable peripheral interconnect (PPI)
48 general-purpose 1/0 pins
EasyDMA automated data transfer between memory and peripherals
Nordic SoftDevice ready with support for concurrent multiprotocol
12-bit, 200 ksps ADC-8 configurable channels with programmable gain
64 level comparator
15 level low-power comparator with wake-up from System OFF mode
lemperature sensor
4x four channel pulse width modulator (PWM) unit with EasyDMA
Audio peripherals – 1’s, digital microphone interface (PDM)
5x 32-bit timer with counter mode
Up to 4x SPI master/3x SPI slave with EasyDMA
Up to 2x 1fC compatible two-wire master/slave
2x UART (CTS/RTS) With EasyDMA
Quadrature decoder (QDEC)
3x real-time counter (RTC)
Single crystal operation
Package variants
- aQFN 73 package, 7 x 7 mm
- QFN48 package, 6 x 6 mm
- WICSP nackage 3 544 y 3 607 mm

Hardware Integration

The MT0, Nordic based chipset, shall be integrated into the host board according to the following specifications in this guide: https://infocenter.nordicsemi.com/pdf/nRF52840_PS_v1.7.pdf *please visit nordicsemi.com for the most current specifications and integration instructions.

Pin Assignments
The nRF52840 device provides flexibility regarding GPIO pin routing and configuration. However, some pins have limitations or recommendations for pin configurations and uses.

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This de-vice may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution
Any changes or modifications not expressly approved by Meraki could void the user’s authority to operate this equipment. This Transmitter must not be co- located or operation in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement
This device complies with RSS -247 of the Industry Canada Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.