GeekSmart L-B201 Fingerprint Door Lock User Manual

GeekSmart L-B201 Fingerprint Door Lock User Manual

How To Use

Specifications

Welcome
GeekSmart bids you welcome to a world of smart home devices, smart locks, and smart surveillance. We at GeekSmart strive to explore and develop the the smart home industry for the good of all. We combine bridge cutting-edge technologies to develop products fit and ready for the market. Please visit our website www.geektechnology.com

• Before installing, please scan the QR codes to watch our easy step-by-step installation video.
• If you have questions regarding the installation process please contact us by mail support@geektechnology.com or by phone 1-844-801-8880.

GeekSmart APP

GeekSmart Youtube Channel

GeekSmart Technical Support

Product Description\

Product Description Preparing For Installation

A. Front handle

B. Rear handle

C. Latch

D. Strike parts

E. Keys & Key hole cover pin

F. Screws B x4

G. Screws A x4

H. Rubber Gasket

Check the door’s dimensions

Step 1 : Measure to confirm that the door is between (35mm~55mm) thick
Step 2: Measure to confirm that the hole in the door is 2″(55 mm)
Step 3: Measure to confirm that the backset is either – (60-70mm)
Step 4 : Measure to confirm that the hole in the door edge is 1″ (25 mm)

Installing Latch and Strike Plate

1. Install latch on the door. Make sure the latch angle faces door jamb.
2. Install the strike on the door frame, ensuring you allow for the bolt to be centered in the strike
   

Installing Exterior Handle

Remember to attach rubber gasket to handle before insertion.

Installing Interior Handle

1. Connect the cable from inside spindle of exterior handle with interior handle.
   

2. Insert interior handle into door, secure it using screw B into the exterior handle

Lock Operation
Use a microfiber cloth and wipe across the fingerprint reader surface.

NOTE : THE FIRST 2 FINGERPRINTS ADDED ARE ADMINISTRATOR. When 2 admin- user fingerprints have  been collected, adding new fingerprints will prompt normal-user fingerprint collection.

Adding fingerprints

Method 1 : Use pin to press the “settings-button” on the interior handle shortly. You’ll be asked to scan your fingerprint. Scan your fingerprint 6 times in sequence. Upon completion, LED will light blue for 2 seconds and lock will prompt “Addition Success”.

Method 2 : Hold your fingerprint to scanner for about 10 seconds until you hear “add administrator fingerprint”. Scan new fingerprint 6 times. Upon completion, LED will light blue for 2 seconds and lock will prompt “Addition Success”.

• Please note the following factors may affect the fingerprint identification.

  1. Fingers are too dry, wet, oily or dirty.
  2. There is direct sunlight on the sensor.

Passage mode
In passage mode the lock will will stay unlocked for convenient free passage.

Enable Passage Mode

Method 1 : Press the mode-switching button on the interior handle to change between modes.
Method 2 : Admin scans fingerprint for 17 seconds until you hear”set to normally open”. LED light flashes 3 times. Lift finger.

Disable Passage Mode
Press the mode-switching button on the interior handle to change between modes.

Delete all fingerprints (Factory Reset)
Use pin to hold press the pin-button on the interior handle for 5-6 seconds. After prompting “initialization success” the lock has been reset and ALL FINGERPRINTS (INCLUDING ADMINS).

Additional Information & notices

a. Upon failed fingerprint verification, LED flashes red for 4 seconds.
b. Upon timed out or abnormal operation, LED lights for 2 seconds.
c. Please take care of your keys and always have a method to open your door.
d. If the fingerprint scanner fails to recognize your fingerprints, try to wipe the scanner and your fingers.

Specifications

Geektechnology Ltd.
1278 Bloomfield Ave
Fairfield, NJ 07004
Toll Free
1-844-801-8880

References

• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>