SounDigital 800.4 Evo X 2 Channel Amplifier Owner’s Manual

: June 5, 2024
: SOUNDIGITAL

Table of Contents

INTRODUCTION
SAFETY INSTRUCTIONS
TECHNOLOGIES
ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER
ELECTRICAL DIMENSIONING AND AUDIO INPUTS
INSTALLATION SEQUENCE
WIRING DIAGRAM
WIRING DIAGRAM / GAIN SETTING
CROSSOVER SET UP
TECHNICAL SPECS
Documents / Resources

YOUR MUSIC. YOUR POWER.
OWNER´S MANUAL
800.4 EVOX₂

INTRODUCTION

DEAR CUSTOMER,
CONGRATULATIONS ON ACQUIRING A PRODUCT WITH THE HIGHEST QUALITY AND TECHNOLOGY!
You have just purchased a SounDigital product of the highest technology and quality, so we thank you for your confidence.
SounDigital products are made with raw materials of the highest quality standards, and the most modern processes, equipment, and technology are used in their production.
On this manual, you will learn about the product, its features, and characteristics, in order to obtain the best result and to be able to enjoy your music with SounDigital quality and power.
To better understand and take advantage of all the functions of the product and use it safely, read this manual carefully and if you have any questions, consult our support by email info@soundigitalusa.com.

PACKAGE CONTENTS

01 800.4 EVOX2 Amplifier
01 Installation quick guide with warranty card
01 Allen wrench 2.0mm
02 Cables for high-level input
01 Promotional sticker

SAFETY INSTRUCTIONS

To prevent injuries to the user or damage to the amplifier, read all safety instructions written in this manual;
If you are insecure about the installation of this equipment, get in touch with our tech support or with a professional specializing in-car audio/vessel audio installation;
Before proceeding with the installation of any electric equipment on your vehicle/vessel, unplug the negative (-) terminal of the battery to avoid fires, injuries, or damages;
Use your sound system safely. The continuous exposure to sound pressures over 85dB may cause irreversible hearing damage; This equipment is for use in DC voltage batteries between 12.6 and 14.4 volts. Before installing the equipment, check the voltage of the batteries; Choose a ventilated place to install the amplifier; Mount the amplifier in a secure way. Avoid mounting it on metallic parts of the vehicle/vessel, because it may cause ground looping (noise); Make sure that the location chosen for the amplifier installation does not affect the operation of the vehicle/vessel; Please select a dry location to mount your amplifier. The products are designed to operate in humid environments but direct contact with water can damage the amplifier.
When passing cables through metallic walls, use rubber O-rings to avoid cable cutting and short-circuits. Clean the amplifier periodically with a brush or dry cloth to assure the thermal efficiency of the heatsink. This product may reach temperatures over 60°C/140°F. Make sure it is cold before touching it; Be careful when making holes in the vehicle/vessel. Make sure you are not making holes in the fuel tank, brake lines, boat hull or electrical cables of the vehicle/vessel; Make sure the cables are properly secured throughout the installation; Wear gloves, safety glasses and all necessary PPE during the installation of SounDigital amplifiers.

Warning! THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THIS INSTRUCTION MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.

TECHNOLOGIES

DYNAMIC THERMAL MANAGEMENT – DTM®

The DTM* is a dynamic thermal recovery system that always maintains the high efficiency of the amplifier by accelerating the thermal exchange of electronic components with the heatsink.

Patent. Required

ULTRA-COMPACT PCB
An intelligent layout, with great use of the P C B a r e a n d t h e u s e o f m o d e r n components with reduced structure guarantee SounDigital products a compact design, at the same time robust and with excellent thermal efficiency.

ROBUST CONSTRUCTION
Thinking about the application of power sports, the product has an extremely robust assembly, both the fixing points and the layout of the PCB were designed to withstand high vibrations, bumps, and impacts.

I – POWER SUPPLY
SounDigital amplifiers are known for their low consumption of batteries, and this feature was improved on the EVOPS Line. The new I-POWER SUPPLY is even more modern, which replaces the old toroidal transformers with a new generation of “E-E” core transformers that deliver efficiency above 90% , ensuring more hours of sound without battery recharge.
Efficiency measured at power supply only

ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER

The plastic covers have the function of finishing and hiding the amplifier fixing screws. To disassemble and assemble them, follow the instructions below.
DISASSEMBLING OF THE PLASTIC COVER

| |
---|---|---
1. Carefully pull out the top of the plastic cover to release the upside latches, as shown in picture 1.
2. Slide up the plastic cover in a continuous movement to remove it.

ASSEMBLING THE PLASTIC COVER

|
---|---
1. To fit the plastic cover back, carefully insert point A of the plastic cover into point B of the amplifier, slowly sliding it down.
2. Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until you hear a clicking noise.

PANELS DESCRIPTION

1
2| CH1/CH2
CH3/CH4| Variable crossover control – 45Hz to 850Hz
---|---|---
3
4| CH1/CH2
CH3/CH4| High Level audio input
(To connect to the speaker output of the headunit)
5
6
7
8| CH1
CH2
CH3
CH4| Audio input – RCA connectors
9
10| CH1/CH2
CH3/CH4| Crossover Switch
Low Pass – Full – High Pass
11
12| CH1/CH2
CH3/CH4| Variable Gain Control

13	CH1	Positive speaker connector
14	CH1	Negative speaker connector

Negative speaker connector
15| CH2| Positive speaker connector
16| CH2| Negative speaker connector
17| CH3| Positive speaker connector
18| CH3| Negative speaker connector
19| CH4| Positive speaker connector
20| CH4| Negative speaker connector
21| –| Positive power supply connector (+12DC)
22| –| Remote power supply connector (REM)
23| –| Negative power supply connector (GND)
24| –| Power ON LED indicator (Blue)

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING
For proper operation of your SounDigital amplifier, you need the proper dimensioning of the electrical system and the cables used.
The table below shows the minimum section of GND cables, +12VDC cables, and speaker output cables according to the power generated by the amplifier.

2400
WRMS| POWER CABLE
GROUND CABLE| 10mm² – 7 AWG
---|---|---
| SPEAKER CABLE| 2 x 1.5mm² – 15 AWG

We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the installation of our products.

AUDIO INPUTS

RCA Inputs

High signal inputs

High input must be used when the main unit does not have RCA outputs.
When hi inputs is used, no remote connection is required, and the amplifier recognizes the audio signal and switches on.
If your source unit is not able to turn on the amplifier through the high- level input, the remote input should be connected normally.

Warning! RCA AND HIGH INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY DAMAGE THE AMPLIFIER.

INSTALLATION SEQUENCE

Warning!
BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM ALL OF THE BATTERIES, TO AVOID FIRE, DAMAGE TO THE AMPLIFIER AND THE USER HIMSELF

Mount the amplifier in such a way you have access to the connectors;
Install the power cables in the vehicle/vessel properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, and install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “Off” position.

Warning! THE MAX: DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS ONE FOOT (30 CM) AWAY FROM THE BATTERY

Connect the power cables to the amplifier, observing the polarity. Connect all the positive cables from the fuse holder or circuit breaker to the positive conector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
The ground cable must be as short as possible and must be connected to the negative the connector of battery or vehicle chassis in case of metallic chassis;

Install the signal input cables in a proper way, distant from the power cables;
Connect the RCA or the high signal input cables to the head unit and amplifiers;
Install the audio output cables with the appropriate section, distant from the power and audio input cables;
Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
Install the remote cable with the power cables, using a 1.5mm² (15 AWG) cable or thicker;
Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output (when not using the high-level signal inputs);
Before powering the system, verify all the connections and make sure there are no
mistakes or short-circuits on the power and ground cables;
Reconnect the ground of the batteries ;
Check if the head unit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
Turn on the main unit and the amplifier will turn on the “On” LED indicating that it is in operation.

WIRING DIAGRAM

4 CHANNELS WIRING DIAGRAM

* Check the minimum speaker impedance at the specs table

3 CHANNELS WIRING DIAGRAM

* Check the minimum speaker impedance at specs table

WIRING DIAGRAM / GAIN SETTING

2 CHANNELS WIRING DIAGRAM

* Check the minimum speaker impedance at specs table

GAIN SETTING
Necessary equipament:

Digital AC voltmeter;
Media with sine wave test tone 60Hzrecorded at 0db;
Screwdriver 1/8″ ( for the gain set)

Set up procedure

This procedure is the same for both gain controls;
Turn the gain control all the way down.
Disconnect the output cables from the amplifier outputs;
Turn off all processing (bass, treble, loudness, EQ, etc.);
Set the source unit volume to 3/4 of full volume.
Set the source unit’s fader control to the center position;
Set the Low Pass switch to “OFF”;
Use a 60 Hz sine wave;
Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and –);
Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);
Once you have adjusted the amplifier to its correct voltage output, turn off the s o u r c e u n i t a n d r e c o n n e c t t h e speaker(s) D o w n l o a d t h e t r a c k s f o r s e t u p i n https://soundigitalusa.com/tracks-for-setup/

MODEL| STEREO / POWER| BRIDGE / POWER| STEREO OUTPUT VOLTAGE| BRIDGE OUTPUT VOLTAGE
---|---|---|---|---
800.4EVOX₂| 2 Ω/ 200W| 4Ω/ 400W| 20.0 V| 40.0 V

CROSSOVER SET UP

“F” All the frequencies are reproduced; “LP ” Set in the variable control on Low Pass Function; “HP ” Set in the variable control on High Pass Function.

Change the switch to “F” position (Full Range): All the frequencies are reproduced.
Change the switch to “HP” position – Set in the variable control between 45Hz and 850Hz (“A”) where you want to perform the high pass cut filter.
Change the switch to “LP” position – Set in the variable control between 45Hz and 850Hz (“B”) where you want to perform the low pass cut filter.

TECHNICAL SPECS

PARAMETERS	800.4 EVOX₂
RMS Power Bridge @ 8Ω*	2 x 264W
RMS Power Bridge @ 4Ω*	2 x 400W
RMS Power @ 4Ω*	4 x 132W
RMS Power @ 2Ω*	4 x 200W
Frequency Response (-3dB)	5Hz ~ 22kHz
Low Pass filter (12dB/oct)	45Hz ~ 850Hz
High Pass filter (12dB/oct)	45Hz ~ 850Hz
Operating Voltage	8V ~ 16V
SNR	95dB
Input Sensitivity	0.2 ~ 4V
Current Draw (Music)	35A
Current Draw (Max)	70A
Total Efficiency	80%
Damping Factor	200
Stereo Minimum Impedance	2Ω
Bridge Minimum Impedance	4Ω
Fuse (music)	40A
Minimum Recommended Battery	50Ah