Laserliner Cubus G Fully Automatic Rotary Laser User Manual

: June 5, 2024
: Laserliner

Laserliner Cubus G Fully Automatic Rotary Laser

Fully automatic rotary laser with red or green laser technology

90° Laser modes: spot, scan, rotary and hand receiver mode.
All functions can be controlled remotely.
Accuracy 0.15 mm / m, 4° self levelling range.

General safety instructions

The device must only be used in accordance with its intended purpose and within the scope of the specifications. The measuring tools and accessories are not toys. Keep out of reach of children. Modifications or changes to the device are not permitted, this will otherwise invalidate the approval and safety specifications. Do not expose the device to mechanical stress, extreme temperatures or significant vibration. The device must no longer be used if one or more of its functions fail or the battery charge is weak. Use only original accessories. Using other accessories invalidates the warranty.

Safety instructions Using class 2 lasers

Laser radiation

Do not stare into the beam! Class 2 laser < 1 mW · 635 nm EN 60825-1:2014/AC:2017.
Do not stare into the beam! Class 2 laser < 1 mW · 515 nmEN 60825-1:2014/AC:2017.

Attention
Do not look into the direct or reflected beam. Do not point the laser beam towards persons. If a person‘s eyes are exposed to class 2 laser radiation, they should shut their eyes and immediately move away from the beam. Under no circumstances should optical instruments magnifying glass, microscope, binoculars be used to look at the laser beam or reflections. Do not use the laser at eye level 1.40 1.90 m. Reflective, specular or shiny surfaces must be covered whilst laser devices are in operation. In public areas shield off the laser beam with barriers and partitions wherever possible and identify the laser area with warning signs. Dealing with electromagnetic radiation. The measuring device complies with electromagnetic compatibility regulations and limits in accordance with the EMC Directive 2014/30/EU. Local operating restrictions for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.

Information on maintenance and care

Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Store the device in a clean and dry place.

Special product features and functions

The rotary laser aligns itself automatically. It is set to the required initial position (to within an operating angle of ± 4° and the automatic system then performs the necessary fine adjustment, with three electronic measurement sensors detecting the X, Y and Z axes. The anti-drift system (ADS) prevents erroneous or inaccurate measurements. How it works: continuous monitoring of the alignment of the laser is activated 30 seconds after the ADS is switched on. If the device moves due to the influence of external factors or the laser loses its height reference, the laser will come to a standstill. Additionally, the laser flashes and the tilt LED is lit continuously. To continue working, press the tilt button again or switch the device off then on again. Erroneous and inaccurate measurements are thus prevented simply and reliably.The ADS is not active following switch-on. Once the device has been set up, press the tilt button to activate the ADS, enabling you to protect the laser from changes in position caused by the device being disturbed by external factors. The tilt LED flashes to indicate that the ADS function is active. The ADS does not activate the monitoring function until 30 seconds after the laser levelling procedure has been completed (set-up phase). The tilt LED flashes every second during the set-up phase, rapid flashing, when ADS is active.

ADS function

Laserliner Cubus G Fully Automatic Rotary Laser 1

Transport LOCK

The device is protected by a special motor brake during transport.The device characterised by specific protection against dustand rain.

Space grids

These show the laser planes and functions auto Automatic alignment / man: Manual alignment.

Horizontal levelling

Vertical levelling

Inclined plane

90° angle

90° reference function.

Battery charging

Use the power supply/charger unit only in closed rooms; do not expose to moisture or rain otherwise risk of electric shock. Charge the device‘s battery completely prior to use. Connect the power pack/charger to the mains power supply and socket (G). Only use the power pack/charger supplied. Using any other power pack/charger will invalidate the warranty. The LED on the power pack/charger (H) lights red while the battery is charging. When the LED changes to green, charging is complete. The LED on the power pack/charger (I) flashes when the laser is not connected to the power pack/charger. The battery can also be charged while using the device. The status indicator (4) flashes when the battery charge is low. Disconnect the power pack from the mains when the device is not in use. Do not remove the red battery insulation from the battery.

Insert batteries into the remote control

Laserliner Cubus G Fully Automatic Rotary Laser 8

Stand and wall bracket

Laserliner Cubus G Fully Automatic Rotary Laser 9

Observing the correct polarity.

A Reference laser outlet.
B Prism head / laser beam outlet.
C Infrared signal receptor.
D Control pane.
E 5/8“ thread.
F Battery compartment.
G Connection socket for power pack/charger.
H Power pack/charger.
.I Operation indicator red: battery is charging
- Green: charging process complete.

Control panel Cubus

Remote control

Laserliner Cubus G Fully Automatic Rotary Laser 13

Auto/slope function.
Auto/slope function LED: LED off: automatic alignmen LED.
Operation indicator LowBat: LED flashes.
Tilt function LED.
Tilt function.
Infrared signal recepto.
Infrared signal emitte.
Operation indicator.
Rotary speed for selection 600 / 330 / 30 / 0 rp
Scan mode 10° / 45° / 90° / 180°
Positioning button rotate to the right.
Positioning button rotate to the left.

Horizontal levelling and vertical levelling

Horizontal

Position the device on a level surface or on a tripod.

Vertical

Place the device on its side with the stand and wall bracket fitted. The operator panel should be at the top. The device with the stand and wall bracket can be mounted on a tripod for
vertical use. Press the ON/OFF switch

auto/slope function LED OFF: Automatic alignment

The device levels itself automatically to within a range of ± 4°. During the set-up phase, the laser flashes and the prism head remains stationary. When levelling is complete, the laser lights up continuously and rotates at maximum speed. If the device has been placed on a surface with a slope of more than 4°, the prism head will remain stationary and the laser as well as the auto/slop LED will start to flash. The device must then be placed on a more even surface.

Slope function

Steeper slopes can be set using the angle plate, which is available as an optional extra.

TIP
Allow the device to align itself automatically and set the angle plate to the zero position. Then press the auto/slope button to switch the automatic sensor off. Finally, incline the device to the angle you require.Auto/slope function LED ON.Auto/slope function LED ON.

LASER LINER Laser modes

Rotary mode

The following speeds can be set using the rotary button: 0, 30, 330, 600 rpm

Spot mode

You access spot mode by pressing the rotary button repeatedly until the laser stops rotating. The laser can then be rotated to the required position using the positioning buttons.

Scan mode

The scan button can be used to activate and set a lightintensive segment in 4 different widths. You position the segment via the direction buttons.

Hand receiver mode

Working with the laser receiver available as an optional extra. Set the rotary laser to maximum speed and switch on the laser receiver.

Working with the reference laser

The device has one reference laser. In vertical mode the reference laser is used to align the device. Align the reference laser parallel to the wall for this purpose. This aligns the vertical laser plane at a right angle to the wall.

Technical data Subject to technical alterations. 20W47

Self-levelling range| ± 4°
Accurancy| ± 0.15 mm / m
Levelling| automatic horizontal vertical levelling with electronic levels and motors
Self-levelling alignment time| approx. 30 seconds over the entire operating angle
Rotation speed| 0, 30, 330, 600 rpm
Laser wavelengths Reference beam red / green| 635 nm / 515 nm
Laser class| 2 / < 1 mW (EN 60825-1:2014/AC:2017
Power supply| 4 x 1.2V HR6 (AA) NiMH
Operating time red / green| approx. 16 h /approx. 10 h
Charging time| approx. 4 h

Operating conditions

| -10° TO 50°C, max. humidity 80% rH, no condensation, max. working altitude 4000 m above sea level
Storage conditions| -10°C TO 70°C,

max. humidity 80% rH

EU directives and disposal
This device complies with all necessary standards for the free movement of goods within the EU. This product is an electric device and must be collected
separately for disposal according to the European Directive on waste electrical and electronic equipment. Further safety and supplementary notices at: http://laserliner.com/info?an=ABO