Apex Cinema Gear Easy XY Fine Adjustment Bracket Installation Guide

Apex Cinema Gear Easy XY Fine Adjustment Bracket

Specifications

• Easy XY Install Instructions
• Included Hardware:
  • A. 1 Easy XY
  • B. 1 Eyebolt
  • C. 1 Ball Stud
  • D. 2 3/8-16 Hex Bolts
  • E. 2 #10 Truss Head Screws
  • F. 2 3/8-16 Square Nuts
  • G. 2 Round Delrin Washers
  • H. 2 Square Delrin Washers
• Tools Needed:
  • Flat Head Screwdriver
  • 5/32 T-Handle Hex Wrench

Product Usage Instructions

• Start by locating either the eyebolt or ball stud, as well as the round Delrin washers. Slide a round washer over the threads and to the top shoulder of the bolt.
• Next, insert the eyebolt or ball stud into the top channel of the Easy XY, ensuring that the Delrin washer stays in place.
• Then, carefully flip over the Easy XY and slide a square Delrin washer over the stud, followed by the 3/8-16 square nut. Hand-tighten the eyebolt or ball stud into the square nut by twisting from the top.
• Next, locate the #10 truss head safety screw and screw it into the stud of the eyebolt or ball stud. Ensure this is secure to prevent accidentally backing the threads out too far.
• Lastly, locate the two 3/8-16 hex bolts and thread them into the two channels. These bolts are captive so you can leave them screwed in and won’t have to worry about losing them!
• Now you’re ready to screw the fully assembled Easy XY onto any camera top handle of your choosing and dial in the perfect balance!

WARNING: Failure to secure the #10 truss head safety screw properly before use will in no event render Apex Cinema Gear liable for any direct, indirect, or special consequential damages whatsoever arising out of or connected with use or misuse of its products.

FAQ

• Q: Can I use Easy XY with any camera?
• A: Yes, you can attach Easy XY to any camera top handle for balance adjustments.
• Q: What should I do if I lose a component?
• A: Contact customer support for replacement parts.

INCLUDED HARDWARE

• A. 1 EASY XY
• B. 1 EYEBOLT
• C. 1 BALL STUD
• D. 2 3/8”-16 HEX BOLTS
• E. 2 #10 TRUSS HEAD SCREWS
• F. 2 3/8”-16 SQUARE NUTS
• G. 2 ROUND DELRIN WASHERS
• H. 2 SQUARE DELRIN WASHERS

TOOLS NEEDED

• FLAT HEAD SCREWDRIVER
• 5/32” T-HANDLE HEX WRENCH

Installation Instructions

STEP 1

• Start by locating either the eyebolt or ball stud, as well as the round Delrin washers. Slide a round washer over the threads and to the top shoulder of the bolt.

STEP 2

• Next, insert the eyebolt or ball stud into the top channel of the easy xy, ensuring that the delrin washer stays in place.

STEP 3

• Then, carefully flip over the easy xy and slide a square Delrin washer over the stud, followed by the 3/8”-16 square nut. Hand-tighten the eyebolt or ball stud into the square nut by twisting from the top.

STEP 4

• Next, locate the #10 truss head safety screw and screw it into the stud of the eyebolt or ball stud. Ensure this is secure to prevent accidentally backing the threads out too far.

STEP 5

• Lastly, locate the two 3/8”-16 hex bolts and thread them into the two channels. These bolts are captive so you can leave them screwed in and won’t have to worry about losing them!

STEP 6

• Now you’re ready to screw the fully assembled Easy XY onto any camera top handle of your choosing and dial in the perfect balance!

Happy Flying!

WARNING- FAILURE TO SECURE THE #10 TRUSS HEAD SAFETY SCREW PROPERLY BEFORE USE WILL IN NO EVENT RENDER APEX CINEMA GEAR LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL CONSEQUENTIAL DAMAGES WHATSOEVER ARISING OUT OF OR CONNECTED WITH USE OR MISUSE OF ITS PRODUCTS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>